View
271
Download
11
Category
Tags:
Preview:
Citation preview
SERVICE MANUALDOCUMENTATION TECHNIQUETECHNISCHE DOKUMENTATIONDOCUMENTAZIONE TECNICADOCUMENTACION TECNICA
No copying, translation, modification on other use authorized. All rights reserved worldwide. • Tous droits de reproduction, de traduction, d'adaptation et d'exécution réservés pour tous les pays. • Sämtliche Urheberrechte an diesen Texten und Zeichnungen stehen uns zu. Nachdrucke,Vervielfältigungen - auch auszugsweise - nur mit unserer vorherigen Zustimmung zulässig. Alle Rechte vorbehalten. • I diritti di riproduzione, di traduzione, e esecuzione sono riservati per tutti i paesi. • Derechos de reproduccion, de traduccion, de adaptacion y de ejecucion reservados para todos los paises.
WARNING : Before servicing this chassis please read the safety recommendations.ATTENTION : Avant toute intervention sur ce châssis, lire les recommandations de sécurité.
ACHTUNG : Vor jedem Eingriff auf diesem Chassis, die Sicherheitsvorschriften lesen.ATTENZIONE : Prima di intervenire sullo chassis, leggere le norme di sicurezza.IMPORTANTE : Antes de cualquier intervención, leer las recomendaciones de seguridad.
- 0603
42WM02L
TV
Plasma
Indicates critical safety components, and identical components should be used for replacement. Only then can theoperational safety be garanteed.
Le remplacement des éléments de sécurité (repérés avec le symbole ) par des composants non homologués selon laNorme CEI 65 entraine la non-conformité de l'appareil. Dans ce cas, la responsabilité du fabricant n'est plus engagée.
Wenn Sicherheitsteile (mit dem Symbol gekennzeichnet) nicht durch Original - Ersatzteile ersetzt werden, erlischt dieHaftung des Herstellers.
La sostituzione dei componenti di sicurezza (evidenziati con il segno ) con componenti non omologati secondo lanorma CEI 65 comporta la non conformitá dell'apparecchio. In tal caso è "esclusa la responsabilità " del costruttore.
La sustitución de elementos de seguridad (marcados con el simbolo ) por componentes no homologados segun lanorma CEI 65, provoca la no conformidad del aparato. En ese caso, el fabricante cesa de ser responsable.
MEASUREMENT CONDITIONS - CONDITIONS DE MESURES - MESSBEDINGUNGENCONDIZIONI DI MISURA - CONDICIONES DE MEDIDAS
RICEVITORE :In UHF, livello d'entrata 1 mV, monoscopio barre :- PAL, norma G. bianco 100%.
Via SCART, livello d'entrata 1 Vpp, monoscopio barre :
Colore, Contrasto, Luminositá media, Suono minimo.Programma selezionato PR 01.
Tensioni continue rilevate rispetto alla massa con un voltmetro digitale.
RECEIVER : On UHF,input level : 1 mV, bar test pattern :- PAL, I standard, 100% white.
Via the scart socket, input level : 1 Vpp, bar test pattern :
Colour, contrast and brightness at mid-position, sound at minimum.Programme selected : PR 01.
DC voltages measured between the point and earth using a digital voltmeter.
EMPFÄNGER : Bei UHF Eingangspegel 1 mV, Farbbalken :- PAL, Norm G, Weiss 100%.
Über die Scartbuchse : Eingangspegel 1 Vss, Farbbalken :
Farbe, Kontrast, Helligkeit in der Mitte des Bereichs, Ton auf Minimum.Zugeordnetes Programm PR 01.
Gleichspannungen mit einem digitalen Voltmeter zur Masse gemessen.
RECEPTEUR : En UHF, niveau d'entrée 1 mV mire de barres- SECAM, Norm L, Blanc 100%.
Par la prise Péritélévision, niveau d'entrée 1 Vcc, mire de barres .
Couleur, contraste, lumière à mi-course, son minimum.Programme affecté PR 01.
Tensions continues relevées par rapport à la masse avec un voltmètre numérique.
RECEPTOR :En UHF, nivel de entrada 1 mV, mira de barras : - PAL, norma G, blanco 100%.
Por la toma Peritelevision, nivel de entrada 1 Vpp mira de barra.
Color, Contraste, luz a mitad de carrera, Sonido minimo.Programa afectado PR 01.
Tensiones continuas marcadas en relacion a la masa con un voltimetro digital.
Do not disconnect modules when they are energized! Repairs on power supply section are to be carried out only with isolating transformer.
Ne pas retirer les modules lorsqu' ils sont sous tension. N'effectuer les travaux de maintenance sur la partie reliée au secteur (Switch Mode) qu'au travers d'un transformateur d'isolement.
Module nicht bei eingeschaltetem Gerät entfernen! Servicearbeiten am Netzteil nur unter Verwendung eines Regeltrenntrafos durchführen.
Non scollegare le piastre quando sono alimentate!Per le riparazioni sulla sezione alimentatore, utilizzare un trasformatore isolatore.
No desconectar los módulos cuando están activados. Las reparaciones en la sección de alimentación de energía deben ser ejecutadas solamente con un transformador de separación.
- 2 -
CONTENTS
Contents ................................................................................................................. 2
Safety Precautions ............................................................................................3
Specifications ..................................................................................................... 4
Control Descriptions ........................................................................................ 5
Adjustment Instructions ............................................................................... 9
Trouble Shooting ............................................................................................... 11
Block Diagram .................................................................................................... 13
Exploded View .................................................................................................. 16
Exploded View Parts List ..............................................................................17
Replacement Parts List ................................................................................ 18
SVC. Sheet ................................................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitary that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on positioin, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each esposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
SPECIFICATIONS Note : Specification and others are subject to change without notice for improvement.
O MONITOR
O Video receiving system:PAL SECAM NTSC-M NTSC 4.43
O Input Voltage : 42PZ17 : AC 200~240V, 50/60HzO Input Voltage : 42PZ15 : AC 110~240V, 50/60Hz
O Power consumption : 300WStand-By : 5W
O PDP Module : PDP42WVSN3
O Speaker Impedance : 8 ohm
O Sound output : 10W max
O Feature : AV Input (Bottom)Component Input (Bottom)RGB Input (Bottom,D-Sub 15pin)External SPK Out (Bottom,SPK Jack) RS-232C
O Funtion : PIP DRP
O External Interface
AV/COMPONENT Output
COMPONENT Mode ( Y,Cb/Pb,Cr/Pr)
- 4 -
ITEM
AV Video in
AV SYNC in
AV Burst in
AV Video in,L/R
AV Audio in,L/R
Component Video in
RGB/HV in
MIN
0.85
0.24
0.14
0.47
0.47
0.6
0.6
TYP
1.00
0.29
0.28
0.63
0.63
0.7
0.7
MAX
1.15
0.32
0.35
0.79
0.79
0.8
0.8
UNIT
Vpp
Vppz
Vpp
V
V
Vpp
Vpp
PIn No123456789
Spec.NC
3.0~4.5Vpp3.0~4.5Vpp4Vpp !0.5
GNDHigh/Low
NCNCNC
Pin NameDCDRXDTXDDTRGNDDSRRTSCTS
RI
REsolution640*480704*4801280*7201280*7201920*10801920*1080
H-Freq(Khz)15.7331.4745.0044.9633.7533.72
V-Freq(hz)60
59.9460
59.9460
59.94
ProposedSDTV,DVD 480I
SDTV 480PHDTV 720PHDTV 720PHDTV 1080IHDTV 1080I
RS-232C Signal
- 5 -
CONTROL DESCRIPTIONS
ON/OFF INPUT VOLUMESELECT
ON/OFF
VOLUMEINPUTSELECT
<Front Panel>
MAIN POWER BUTTONSwitchs On or Off
INPUT SELECT BUTTON
REMOTE CONTROL SENSOR
POWER/STANDBY INDICATORIlluminates red in standbyIlluminates green when the Monitor is switched on
POWER BUTTONStandbyStart
VOLUME (FF,GG) BUTTON
To preserve your W ysius ™ screen Your Wysius ™ could be damaged if a bright fixedpicture is displayed on its screen for too long. Theplasma screen of your Wysius ™, like any televisionor computer monitor screen, could be permanentlyimprinted with this fixed image. It is thereforerecommended to avoid displaying the same fixedpicture (like a DVD or a VCR menu) for more than 10minutes.
- 6 -
AC INPUTRGB PC INPUT(VGA/SVGA/XGA)
(+) ( ) (+)( )
EXTERNAL SPEAKER
R L R
AUDIO INPUT RS-232C
L
(+) ( ) (+)( )
AC INPUTEXTERNAL SPEAKER
R L R
AUDIO INPUT RS-232C
L
RGB PC INPUT(VGA/SVGA/XGA)
PB RY P
AV INPUT S-VIDEO
R LAUDIO <MONO> VIDEO
COMPONENT (480i/480p)(DVD INPUT)
PBY RP
AV INPUT S-VIDEO (DVD INPUT)COMPONENT (480i/480p)
R LAUDIO VIDEO(MONO)
<Back Panel>
EXTERNALSPEAKER (8Ω)KNOBS
AV INPUT /COMPONENT (480i/480p)DVD INPUT SOCKETSG The Interface board VB02L is optional (not supplied).
RGB PC INPUT(VGA/SVGA/XGA) /AUDIO INPUT / RS-232C SOCKET
POWER INPUTSOCKETThis Monitor operateson an AC mains supply,the voltage is as indicat-ed as inside back coverof this manual. Neverapply DC power to theMonitor.
Tips• The RS-232C socket is for production purpose only. Do not connect anything on it.
- 7 -
Accessories
D-sub 15 pin cable
Manuel d ’u t i l isat ion
User manual
Bedienungsanle i tung
Manuale d i u t i l i zzaz ione
Manual de ut i l izac ión
42 WM 02 L - 42 WM 02 LU
User Manual
Power cord Remote control handset
Optional Extras
- Optional extras can be changed or modified for quality improvement without any notification newoptional extras can be added.
- Contract your dealer for buying these items.
VB02L (Interface board)
PB
Y
RP
RL
AUDIO
VIDEO(MONO)
AV INPUT
S-VIDEO(DVD INPUT)COMPONENT (480i/480p)
ACC912(Wall mounting bracket)
TBST4292(Desktop stand)
ACC143(Speakers)
SCART/RCA cable
- 8 -
Illuminates the keys of the remote control.
Standby Start
Navigating Up in a menu.
Navigating Down in a menu.
Validation.
Right / Left selection in the menus.
Selection of connected devices (connectors).
Accessing (menu ) and quitting (exit ) themenus.
The remote control of your Wysius ™ controls your monitor aswell as the functions of other devices described on page 9.
To control the monitor, switch this
key to the plasma position.
Video S-V ideo
RGB Component
To select pictures from a PC.
To select the Sleep Timer.
Format control.
To go back to your preferred Soundsettings.
To go back to your preferred Picturesettings.
4/3 16/9 Zoom
- 9 -
1. Application ObjectThese instructions are applied to all of the PDP monitor, NF-01DC.
2. Notes(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 220/230V,50/60Hz in adjusting.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
1) After receiving 100% white pattern, the receiver must beoperate prior to adjustment.(Or white condition in HEAT-RUN mode)
2) Enter into HEAT-RUN mode - Select the HEAT-RUN by pressing ADJ button on
Remote Control for adjustment.- Press the VOL + button in HEAT-RUN OFF.(OSD display HEAT-RUN WHITE and screen display100% full WHITE PATTERN)
3) Set is activated HEAT-RUN without SET TOP BOX orsignal generator in this mode.
[ Single color pattern of HEAT-RUN mode uses to checkPANEL.(RED/BLUE/GREEN)
[Caution] If you turn on a still screen more than 20 minutes, aafterimage may be occur in the black level part of thescreen.
3. POWER PCB Assy V oltage Adjustment[ Replace PDP Module or Power Board, adjust certainly Power
PCB Assy Voltage.
3-1. Test EquipmentD.M.M 1EA
3-2. Connection Diagram for MeasuringRefer to Fig 1.
3-3. Adjustment Method
(1) Va Adjusment(Address Voltage Adjusment)1) Connect pin 1 of CN806 or CN811 to (+) jack of D.M.M.2) After turning the VR351(Va Adj), voltage of D.M.M
adjustment as same as Va voltage which on label ofpanel right/top.(Deviation : ±0.5V)
(2) Vs Adjustment1) Connect pin 1 of CN803 to (+) jack of D.M.M.2) After turning the VR551(Vs Adj), voltage of D.M.M adjust
as same as Vs voltage which indicated on label of panelright/top.(Deviation : ±0.5V)
(3) V-y Adjustment1) Connect pin 1 of CN802 to (+) jack of D.M.M.2) After turning the VR751(V-y Adj), voltage of D.M.M
adjust as same as Vs voltage which indicated on labelof panel right/top.(Deviation : ±0.5V)
(4) Vsetup Adjustment1) Connect pin 5 of CN802 to (+) jack of D.M.M.2) After turning the VR651(Vsetup Adj),voltage of D.M.M
adjust as same as Vs voltage which indicated on labelof panel right/top.(Deviation : ±0.5V)
(5) 5V Adjustment1) Connect pin 3 of CN809 to (+) jack of D.M.M.2) Adjust the voltage data of D.M.M to 5.1V by
turning.(Deviation : ±0.05V)
(6) STBY-5V Adjustment1) Connect pin 3 of CN808 to (+) jack of D.M.M.2) Check the voltage(5V) of D.M.M.3) Adjust the voltage data of D.M.M so that voltage data of
D.M.M is 5V.(Deviation : ±0.05V)
ADJUSTMENT INSTRUCTIONS
Vs
Va CTL
- Vy CTL
VR751
Vsetup CTL
VR651
- VyVsetup
Vs
- Vy CTL
VR751
Vsetup CTL
VR651
- VyVsetup
Va
CN811
CN809
CN808
5V
CN806
CN802 CN803
STBY 5V
VR 351
Va CTL
VR 253
5V
VR 151
STBY 5V
Va CTL
VR 551
Vs CTL
<Fig 1> Connection Diagram of Power Adjustment for Measuring
Refer to Typical Voltage
Va
Vs
Vy
Vsetup
60 ~ 75V
170 ~ 185V
-60 ~ -90V
210 ~ 240V
- 10 -
4. Adjustment of White Balance
4-1. Required EquipmentColor analyzer(CA-100 or same production)
4-2. Connection Diagram of Equipment forMeasuring
[ After stop the Micom by pressing IN-START Key on RemoteControl, insert the P1002 with automatic adjustment ofconnector. After remove connector, move the Micom by pressing ENTERKey.
4-3. Adjustment of White Balance• White Balance should be done after RGB cut-off become
adjustment.• Operate the Zero-calibration of the CA—100, then stick
sensor to PDP module surface when you adjust.
(1) Select WHITE PATTERN of HEAT RUN mode by pressingADJ button on Remote Control for adjustment then operateHEAT RUN more than 15 minute.
(2) Supply 10 step gray scale bar signal in pattern generater.(A/V Input)
(3) To adjust Low Light, stick sensor to 9th pattern(Dark),select the W/B by pressing ADJ button on Remote Controlfor adjustment and press the VOL + button enterAdjustment Mode.After select the G cut and B cut, press the VOL +/- Keyand adjust it until color coordination becomes (R cutfixation)color coordination : X=0.270±0.003, Y=0.280±0.003color temperature : 10,000cK ± 500cK
(4) To adjust High Light, stick sensor to 2th pattern(White),select the W/B by pressing ADJ button on Remote Controlfor adjustment and press the VOL + button enterAdjustment Mode.After select the R GAIN and G GAIN, press the VOL +/-Key and adjust it until color coordination becomes (B GAINfixation)color coordination : X=0.270±0.003, Y=0.280±0.003color temperature : 10,000cK ± 500cK
(5) Confirm the result of the High Light adjustment.If the deviation of High Light occur, operate the adjustmentof Low Light and High Light again.
(6) Exit adjustment mode using Enter button.
COLORANALYZER
TYPE; CA-100
Window Pattern
CVBS Signal InputHigh Light85±5cd/m2
Low Light8±3cd/m2
PDP MONITOR
MSPG-2100 orMSTG-5200
<Fig 3> Connection Diagram of Automatic Adjustment
- Vy
Vsetup
Vs
Va
Vsetup ADJ VR8104
Va ADJ VR8105
Vs ADJ VR8102
- Vy ADJ VR8103
<Fig 2> Connection Diagram of POWERWEL Power Adj. for Measuring
- 11 -
TROUBLESHOOTING
1. No Video
2. No Sound
Abnormal Picture
Input PC signal.
Normal
Abnormal
Check CXA2101IC203
Normal
Check ADV7123IC406
Check JAGASMIC501
Check 74F541DIC902~IC905
Check cable of pin 41P902
Normal
Check FLI2220IC404
Normal
Check FLI2200IC403
Normal
Check VPC3230IC201
Normal
Check Input jack & Connector.
Check connector speaker to set.
Check MSP3401IC601
Check LA4282IC603
Check InputJack.
- 12 -
3. No Video
4. No Sound
Nothing output of image.
Check Input of AC.(90~225V)
Normal
Abnormal
Abnormal
Abnormal
Check ST-BY LED ONMain S/W ON.
Normal
Check LED YELLOWSub S/W ON.
Connect plug with the set.
Check AC Line Fuse.
Check OPEN withCN802,CN803,CN804.Check the Vs voltage
and Q603,Q703 short.
AbnormalReplace Q603,Q703
Normal
Check a connective condition and various connector.
Check a connectivecondition of power cable.
Check voltage of soundterminal.
Check Open with F8811Fuse.
Check connectionline of speaker.
- 13 -
BLOCK DIAGRAM1. VSC
MIC
OM
EE
PR
OM
X24
16P
AU
DIO
LR
AU
DIO
AM
PLA
4282
(L &
R)
5R
GB
HV
CO
LOR
DE
CO
DE
R
(VP
C32
30D
)
DE
INT
ER
LAC
E(F
LI22
00)
ME
MO
RY
(4M
-BY
TE
)
EN
HA
NC
ER
(FLI
2220
)
CO
LOR
CO
NT
RO
L&
VID
EO
SW
ITC
H
(CX
A21
01Q
)
3Y
,Pb,
Pr(
MN
T)
SC
ALE
R
(JA
GA
SM
)
ME
MO
RY
(8M
-BY
TE
)
EP
LD
(GE
N. C
LAM
P)
Buf
fer
(74F
574
x 4
)
H V Cla
mp
2H
/V
H
5H
/V/C
LK/
HB
LK/V
BLK
4
H/V
/DE
/CLK
5
RG
BH
V
3R
GB
AU
DIO
SW
ITC
H
(LA
7222
)
2
H/V
PO
RT
EX
P(M
6232
0X4)
RO
M(A
T29
C01
0)
(74H
CT
373)
YC
bCr/
YP
bPr
CV
BS
Y/C
41P
4
4H/V
/F
IELD
/LL
C1
2H
/V
DA
C(A
DV
7123
)5
RG
BH
V16 Y
UV
30RG
B
RG
B
30
YU
V16
24 RG
B
2
Rx,
Tx
Dig
ital L
ine
Ana
log
Line
H/V
/DE
/CLK
24 RG
B
- 14 -
2. POWER
RE
LAY
_ON
5V_M
ON
I
Vs_
ON
AC
_ON
5V (
MA
IN)
GN
D
Va
GN
D
Vs
GN
D
GN
D
Vse
tup
GN
D
-Vy
GN
D
GN
D
15V
GN
D
12V
30V
INP
UT
110~
220V
AC
RE
CT
IFIE
R
FIL
TE
R(F
OR
EM
I)R
EC
TIF
IER
AC
MO
NIT
OR
RE
CT
IFIE
R&
FIL
TE
R
RE
CT
IFIE
R
5VM
ON
ITO
RMIC
OM
5V (
ST
-BY
)
GN
D
DC
/DC
CO
NV
.
RE
GU
LAT
OR
DR
IVE
&R
CC
SW
ITC
HIN
G
O.V
.P, U
.V.P
DE
TE
CT
OR
DR
IVE
PF
C
CO
NT
RO
L &
DR
IVE
PF
CS
WIT
CH
ING
RE
CT
IFIE
R&
FIL
TE
RF
ILT
ER
DR
IVE
&F
LYB
AC
KS
WIT
CH
ING
DR
IVE
&F
LYB
AC
KS
WIT
CH
ING
DR
IVE
&F
OR
WA
RD
SW
ITC
HIN
G
DR
IVE
&R
CC
SW
ITC
HIN
G
MEMO
- 15 -
- 16 -
EXPLODED VIEW
301
303
302
200
203
201
202
205
211
204207
208
209
206
400
540
401
550
551
530
560
570
300
212
305
520
580
- 17 -
EXPLODED VIEW PARTS LIST
200 35689470 PDP 42” 16:9 852*480 FOR DND INTER
201 35689540 PWB ASSY,DISPLAY ZCNT ASSY HAND INSERT
202 35689550 PWB ASSY,DISPLAY ZSUS ASSY HAND INSERT
203 35689560 PWB ASSY,DISPLAY ZCNT ASSY HAND INSERT
204 35689570 PWB ASSY,DISPLAY XRRT ASSY HAND INSERT
205 35689580 PWB ASSY,DISPLAY XRLT ASSY HAND INSERT
206 35689590 PWB ASSY,DISPLAY YSUS ASSY HAND INSERT
207 35689600 PWB ASSY,DISPLAY YDRV ASSY SMD BOTTOM INSERT
208 35689610 PWB ASSY,DISPLAY YDRV ASSY SMD TOP INSERT
209 35689620 PWB ASSY,DISPLAY CTRL ASSY HAND INSERT
300 35689710 CABINET ASSY
301 35689720 SUPPORTER ASSY FILTER TOP
302 35689730 SUPPORTER ASSY FILTER BOTTOM
303 35689740 SUPPORTER ASSY FILTER SIDE
305 35689750 FRONT GLASS FILTER
400 35689870 BACK COVER ASSY
520 35689630 PWB ASSY,MAIN
530 35689640 BOARD ASSY,PDP POWER LINE-FILTER
540 35689650 PWB ASSY,MNT CONT
550 35689660 PWB ASSY,MNT POWE
560 35689670 PWB ASSY,MNT SPK
570 35689680 BOARD ASSY,POWER BOARD
No. Part No. Description
P/N: 3854VA0100B-S1(1/2)2002.03.05
P/N: 3854VA0100B-S1(2/2)2002.03.05
P/N: 3854VA0100B-S2(1/2)2002.03.05
P/N: 3854VA0100B-S2(2/2)2002.03.05
Recommended