Removing HP Compaq dx2000MT Motherboard€¦ · 步骤 1 — Case Doors Turn off your computer and...

Removing HP Compaq dx2000MT MotherboardRemove the motherboard

撰写者: Logan Pace

Removing HP Compaq dx2000MT Motherboard 草案： 2014-01-28指南 ID： 6701 -

æ ¤æ–‡æ¡£ç”Ÿæˆ äºŽ 2020-01-18 09:59:03 AM (MST)ã€‚

介介绍绍

This guide will show you how to remove the motherboard on your HP Compaq dx2000MT

工具工具:Anti-Static Wrist Strap (1)Flathead Screwdriver (1)Phillips #2 Screwdriver (1)2.5 mm Flathead Screwdriver (1)T15 Torx Screwdriver (1)Tweezers (1)High Content Rubbing Alcohol (1)

步骤步骤 1 — Case Doors

Turn off your computer and removethe power cable by pulling it straightout of its socket.

步骤步骤 2

Remove the two Phillips #2 screws that secure the case door to the device.

步骤步骤 3

Remove the side case door by pushing towards the rear of the device with your hand.

This may take considerable force so keep pushing!

Once you slide the door back, remove it by pulling it outwards from the device.

步骤步骤 4

Remove the side case door by pushing towards the rear of the device with your hand.

Once again, this may take considerable force.

Once you slide the door back, remove it by pulling it outwards from the device.

步骤步骤 5 — Optical (CD) Drive

Remove the IDE data cable and the power cable from the optical drive by pulling away from thedrive.

步骤步骤 6

Remove the 2 Torx T15 screws holding the optical drive in place.

步骤步骤 7

Remove the other 2 Torx T15 screws holding the other side of the drive in place.

步骤步骤 8

Remove the optical drive by sliding it out the front of the device.

步骤步骤 9 — Disassembling HP Compaq dx2000MT Hard Drive

Remove the IDE data and power cables from the hard drive.

步骤步骤 10

Remove the front bezel by pulling upwards and out from below the lowest air vent.

步骤步骤 11

Remove the external drive faceplate by removing the two Torx T15 screws.

步骤步骤 12

Remove the following screws:

Front Torx T15.

Torx T15 mounting the hard drive cage to the optical drive bay.

步骤步骤 13

Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.

步骤步骤 14

Remove the two Torx T15 screws holding this side of the hard drive in place.

步骤步骤 15

Proceed to the other side of the hard drive cage.

Remove the two Torx T15 screws holding this side of the hard drive in place.

步骤步骤 16

Remove the hard drive from the hard drive cage by pulling it outward from the cage.

步骤步骤 17 — Case Fan

Remove the 3 prong power connector from the motherboard by pulling it outwards toward the sideof the device.

步骤步骤 18

Remove the 4 push fasteners from the case by:

Prying them outwards with a small flathead screwdriver and

Pulling them out with tweezers or plyers.

步骤步骤 19

Remove the fan from the case by pulling it towards the front of the device.

步骤步骤 20 — PCI Cards

Remove the Torx T15 screwdriver holding the PCI card in place.

步骤步骤 21

Remove the PCI card by pulling itout towards the side of the device.

Be careful about touching the topand bottom of the card! The staticelectricity in your fingers could shortit. If you can, only touch the metalbracket and the sides of the card.

步骤步骤 22 — RAM

Release the lower portion of the RAM by pushing down on the bottom tab.

步骤步骤 23

Release the upper portion of the RAM by pushing down on the upper tab.

步骤步骤 24

Remove the RAM by pulling it out towards the side of the device

Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity inyour fingers could short it. If you can, only touch the top and bottom of the RAM.

If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise theRAM may not fit or your computer may not start up.

步骤步骤 25 — Power Supply

Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latchand pulling out towards the side of the device.

步骤步骤 26

Remove the 20 pin ATX power connector from the motherboard by pressing down the holdinglatch and pulling out towards the side of the device.

步骤步骤 27

Remove the 4 Torx T15 screws from the rear of the power supply

步骤步骤 28

Slide the power supply towards the front of the device

Keep your hand underneath it! You don't want to drop it!

Then pull the power supply down and remove it from the case.

步骤步骤 29 — Motherboard

Remove any IDE cables from the motherboard by pulling them out towards the side of the device.

步骤步骤 30

Remove the 2 prong speaker connector by pulling out towards the side of the device.

步骤步骤 31

Remove the 16 pin connector from the motherboard by pulling it out towards the side of the device.

步骤步骤 32

Remove the 14 pin USB connector by pulling it out towards the side of the device.

步骤步骤 33

Remove the 8 Torx T15 screws from the motherboard.

步骤步骤 34

Remove the 3 pin power connector by pulling it out towards the side of the device.

步骤步骤 35

Unscrew the 4 Torx T15 screws holding the CPU Cooler in place.

Make sure to hold your cpu cooler when removing the screws. You don't want it to fall!

步骤步骤 36

Remove the cpu cooler by pulling out towards the side of the device.

Make sure you do not touch where the cpu cooler makes contact with the processor! You do notwant to contaminate the thermal paste that separates these components.

When replacing your cpu cooler, make sure you clean the processor contact area on the coolerand processor with isopropyl rubbing alcohol.

We have a guide for reapplying thermal paste that makes this easy.

To reassemble your device, follow these instructions in reverse order.

步骤步骤 37

Remove the motherboard by pushing it forwards and removing it from the case.

Removing HP Compaq dx2000MT Motherboard€¦ · 步骤 1 — Case Doors Turn off your computer and...

Documents

Christina Haberfellner DerNutzenvonForschungs ...klinkhardt.ciando.com/img/books/extract/3781554953_lp.pdf · Th e scales can be used to refl ect own attitudes, to remove fears and

Gesellschaftswagen „Fanzug-Wagen“ 43948€¦ · music file converted on the memory card from other acces-sible formats as described below. Changing the Music 1 Remove the micro-SD

CNAS L6957 Report No. : S-17120136 · 2018-05-14 · Vibration 振动 1.1 Test procedure 测试步骤 Cells and batteries are firmly secured to the platform of the vibration machine

7438 NAV1 Fokker DrI - Eduard · 2016. 10. 20. · 7438 1/72 fokker dr.i optional volba bend ohnout open hole vyvrtat otvor symetrical assembly symetrickÁ montÁŽ remove odŘÍznout

Bedienungsanleitung User’s Manual - seben.com Target.pdf · Detailed instruction how to assemble the Deep Target metal detector: • Remove the big plastic-headed screw (1) on the

Übersetzung von XSEL-Ausdrücken in andere XML-Updatespracheneprints.dbis.informatik.uni-rostock.de › 76 › 1 › XML-Schema_Evolutio… · xupdate:remove : remove entfernt bestehende

SICHERHEITSDATENBLATT MATERIAL SAFETY DATA SHEET …...handling and before break with soap and water. Wear protective personal clothing (section 8.) Remove all contaminated clothes

第八章常见问题解答 - Lenovo · 常见问题解答91 明，打开机箱上盖，检查并确定所有接插件正确牢固插接。二、清除系统配置以下操作引起的故障请按照第四章里的操作步骤，清除系统当前配置，恢复到缺省状态。

Modell der Diesellokomotive 70230 - static.maerklin.de · • Loosen the hex head screw on the rear drive wheel with a traction tire. • Remove the side rods and drive rods. •

37 AGONISTISCHE AUTOANTIKÖRPER ALS …€¦ · he complex therapy including Sujok, classic and auricular acupuncture, moxibustion and Yamo-moto scalp acupuncture can help to remove

10026798 BDA Spanferkelgrill OneConcept · Motor.If necessary, add more coals by lifting the grills with the grills with the tool supplied When fi nished cooking,carefully remove

Stichwortverzeichnis - application.wiley-vch.de · Stichwortverzeichnis – remove 319 – Request 314 doWork 512 dp 160,175,183,563 dpi 563 Drawables 161 DrawerListener 633 Druck

IMPORTANT SAFEGUARDS - Microsoft · Il est possible que l’article sur la photo soit différent du produit réel ... Item da foto pode diferir do produto real ... Remove the battery

Satinelle sensitive - Philips€¦ · With your new Satinelle Sensitive BodyTotal epilator you can remove undesired hair quickly, easily and effectively: not only from your legs,

Windows 8/8.1 Windows 10 Boot Manager Error …...步骤 3 Connect your device. If there is no reaction from Windows for a connected new device, restart the phone. Press and hold the

MD/ME 系列條碼機操作手冊marrisonprinter.com/images/dow/manual/3.pdf · 步驟-05 使用USB 連接，搜尋印表機裝置型號如右圖，點選Marrison MD120 後，選”下一步”

Solid Edge 同步建摸技术介绍 · 2018-11-05 · 同步建模是Solid Edge 的发展方向原型制定 2008 同步技术发布 Solid Edge应用到零件和装配 2009 同步技术应用延

1768 CompactLogix 控制器 - Rockwell Automation...Manual (Logix5000 控制器通用编程步骤手册，出版号：1756-PM001) 旨在指导 Logix5000 控制器项目的开发。它提供了到各个指南的链接。Logix5000

Betriebsanleitung Zubehör IR Detektor VECTRON G05/06 ......Burner VECTRON G05/06 DUO PLUS / VARIO • Remove plastic cap 6 on gas cover. • Remove plastic cap 7 on electrical plate

Der Wal im Windkanal€¦ · Legacy Dependency Hell - explained: ... docker run -v /:/tmp ubuntu rm -rf /tmp/* Which will remove all the files on your system. ... around deploying