High speed steel Carbide tools Bud welded · KIM Komeetstaal HIGH-SPEED-STEEL TOOL/HOLDERS Catalogue 2008 Page 4 Holder Level of cuttingedge Length Section SW16 16 130 17x19 SW20

Cataloguskomcateng

01-2008

KIM KomeetstaalPostbus 51 - 7000 AB Doetinchem Fabriekstraat 42 - 7005 AR DoetinchemTel: (0314) 343000 Fax: (0314) 332471E-mail: [email protected] Site: www.komeetstaal.nl

The Netherlands

High speed steelCarbide tools

Bud welded

Table of contentsDescription tool per page Pag. Description tool alphabetic Pag. Type alphabetic Pag.Horizontal rough-turning tool/holder HR 2 Adjustable boring tool/holder VBH 5 105 13Vertical rough-turning tool/holder VR 2 Assortiment case AS10VOL 4 106 13Finish-turning tool/holder HM 2 Assortiment case AS14VOL 4 113 13Vertical knife tool/holder VM 2 Assortiment case AS16VOL 6 114 13Grooving tool/holder AZ 3 Assortiment case AS20VOL 6 127 15Grooving tool/holder AH 3 Bent roughertool 113 114 213 214 13 137 15Grooving tool/holder RA 3 Bent roughing tool 72 HM 10 138 15Flexible parting-off tool/holder VA 3 Boring head AB 6 139 15Parting-off tool/holder SW 4 Boring rod BST 6 140 15Flexible threading tool/holder VD 4 Boring tool 73 HM 10 149 14Toolbit holder EM 4 Boring tool 73RO HM 10 155 14Toolbits EM14 4 Boring tool 74 HM 11 163 16Toolbits AM10 4 Boring tool 74RO HM 11 164 16Assortiment case AS10VOL 4 Boring toolholder 180 17 171 17Assortiment case AS14VOL 4 Boringtool side/face 171 173 17 173 17Toolbit holder TR 5 Cutting speeds for carbide tools 12 180 17Fixed boring tool/holder BH6 5 Detachable boring tool/holder BH 6 181 17Fixed boring tool/holder BH8 5 Diamond nose tool 127 227 15 185 17Adjustable boring tool/holder VBH 5 External threading tool 187 189 16 187 16Fixed boring tool VB 5 Facing tool 79 HM 10 189 16Detachable boring tool/holder BH 6 Finish-turning tool/holder HM 2 201 13Boring rod BST 6 Fixed boring tool VB 5 202 13Boring head AB 6 Fixed boring tool/holder BH6 5 205 13Assortiment case AS16VOL 6 Fixed boring tool/holder BH8 5 206 13Assortiment case AS20VOL 6 Flexible parting-off tool/holder VA 3 213 13Toolbits square 7 Flexible threading tool/holder VD 4 214 13Toolbits round 7 Form tool 76 HM 10 225 16Toolbits rectangle 7 Grooving tool 155 255 256 14 227 15Keyway toolbits 7 Grooving tool/holder AH 3 237 15

Grooving tool/holder AZ 3 238 15Selection chart HSS 9 Grooving tool/holder RA 3 239 15Straight roughing tool 71 HM 10 Horizontal rough-turning tool/holder HR 2 240 15Bent roughing tool 72 HM 10 Inside threading 82 HM 11 249 14Form tool 76 HM 10 Internal recessing tool 83 HM 11 250 14Facing tool 79 HM 10 Internal threadingtool 181 185 17 255 14Knife tool 80 HM 10 Keyway toolbits 7 256 14Parting off tool 81 HM 10 Keyway-tool 8 263 16Boring tool 73 HM 10 Knife tool 137 138 237 238 15 264 16Boring tool 73RO HM 10 Knife tool 80 HM 10 401 18Boring tool 74 HM 11 Outside threading 75 HM 11 407 18Boring tool 74RO HM 11 Parting off tool 81 HM 10 425 18Single point tool 75 HM 11 Parting-off tool 149 249 250 14 449 18Outside threading 75 HM 11 Parting-off tool/holder SW 4 7100 10Inside threading 82 HM 11 Recessingtool 175 17 7200 10Internal recessing tool 83 HM 11 Roughtool HSco 105 106 201 202 205 206 13 7300 10Vee-pulley grooving tool 85 HM 11 Selection chart HSS 9 7400 10Cutting speeds for carbide tools 12 Side tool 139 140 239 240 15 7500 11Roughtool HSco 105 106 201 202 205 206 13 Single point tool 75 HM 11 7500 11Bent roughertool 113 114 213 214 13 Slotter tool 76000 18 7600 10Parting-off tool 149 249 250 14 Square nose finishing tool 225 16 7900 10Grooving tool 155 255 256 14 Straight roughing tool 71 HM 10 8000 10Diamond nose tool 127 227 15 Swan-necked planing tool 401 407 425 449 18 8100 10Knife tool 137 138 237 238 15 Swan-necked tool 163 164 263 264 16 8200 11Side tool 139 140 239 240 15 Toolbit holder EM 4 8300 11Square nose finishing tool 225 16 Toolbit holder TR 5 8500 11External threading tool 187 189 16 Toolbits AM10 4 76000 18Swan-necked tool 163 164 263 264 16 Toolbits EM14 4 AB 6Boringtool side/face 171 173 17 Toolbits rectangle 7 AH 3Recessingtool 175 17 Toolbits round 7 AM10 4Internal threadingtool 181 185 17 Toolbits square 7 AS10 14 4Boring toolholder 180 17 Vee-pulley grooving tool 85 HM 11 AS16 20 6Swan-necked planing tool 401 407 425 449 18 Vertical knife tool/holder VM 2 AZ 3Slotter tool 76000 18 Vertical rough-turning tool/holder VR 2 BH 6

BH6 - 8 5BST 6EM 4

EM14 4HM 2HR 2

KIM Komeetstaal HIGH-SPEED-STEEL TOOL/HOLDERS Catalogue 2008 Page 2

KIM KomeetstaalPostbus 517000 AB Doetinchem The NetherlandsFabriekstraat 427005 AR Doetinchem The NetherlandsTel.: ++31(0) 314 343000Fax.:++31(0) 314 332471E-mail: [email protected]: www.komeetstaal.nl

HR - HORIZONTAL ROUGH-TURNING TOOL/HOLDERIts rigid design makes this horizontal rough-turnig tool particularly suited for heavy metal-removal both on a lathe and on a planing machine.One end is ground as RIGHT-HAND (RH) tool and theother end as a LEFT-HAND (LH) tool. The tool shouldbe “short”clamped, which prevents chattering and tool breakage.

VR - VERTICAL ROUGH-TURNING TOOL/HOLDERA vertical rough-turning tool which permits heavymetalremoval. The tool can also be detached forbeing reground, (top side only) without unclampingthe holder.

Holder level of Cuttingedge Length SectionHR16 16 125 21x22HR20 20 150 23x25HR25 25 180 26x32

Tool Length SectionHR16d 125 10x10x10HR20d 150 12x12x12HR25d 180 15x15x15

HM - FINISH-TURNING TOOL/HOLDERThe horizontal knife tool/holder can be used both for right handand left hand turning. It is extremely practable for generalpurpose and precision finish-turning service. To obtain a mostefficient use of the tool, it is advisable to regrind the front only,so that its profile, top and side rake remain unchanged, whichprovides you with an excellent cutting edge.

Holder Level of cuttingedge Length SectionVR16 16 adjustable 150 14x16VR23 23 adjustable 180 19x23

Tool Length SectionVRM16d 45 5x9x20VRM23d 50 6x11x28

Holder Level of cutting edge Length SectionAZ12 12 100 11x16AZ14 14 125 11x18HM16 16 125 18x22,5HM20 20 150 19x26,5HM23 23 180 20x30,5HM26 26 210 21x32,5

VM - VERTICAL KNIFE-TOOL/HOLDERA rigid tool holder with a vertically adjustable knife tool,which allows turning as far as up to the chuck or collet.The tool can easily be adjusted or removed withoutunclamping the holder.

Tool Length SectionHM12d 75 8x3HM14d 100 10x4HM16d 125 12x7HM20d 150 16x7,5HM23d 180 18x8HM26d 210 20x8,5

Holder Level of cuttingedge Length SectionVM16 16 adjustable 150 14x16VM23 23 adjustable 180 19x23

Tool Length SectionVRM16d 45 5x9x20VRM23d 50 6x11x28

AZ - GROOVING TOOL/HOLDERThis type has the advantage that the tool is fittedinto the side of the holder. Grooving or cutting offclose to the chuck or collet is therefore possible.The tool can be re-adjusted without unclampingthe holder.


AH - GROOVING TOOL/HOLDERThis more rigid AH holder is particularly suited forheavy grooving.The tool can be re-adjusted without unclampingthe holder.

Holder level of Cuttingedge Length SectionAZ12 12 100 11x16AZ14 14 125 11x18AZ16 16 135 12x22

Tool Length SectionAZ12d 75 8x2x1,5AZ14d 100 10x2,5x2AZ16d 125 12x3,5x3

Holder level of Cuttingedge Length SectionAH16 16 125 16-19x24AH20 20 150 17-21x27,5AH25 25 150 17-22x33

RA - GROOVING TOOL/HOLDEROwing to its shape the RA - holder can be clamped shortand may be used for grooving/cutting-off workpieces‘on the chuck’. the tapered clamping prevents lateral springingand permits grooving as far as up to the chuck or clooet.The tool can be re-adjusted without unclampingthe holder.

Tool Length SectionAH16d 125 12,0x3,0x2,2AH20d 150 14,5x4,0x3,0AH25d 150 17,5x5,0x4,0

Holder level of Overall Sectioncuttingedge length holder

RA16 16 120 10x20RA19 19 140 12x25RA22 20 150 13x26RA24 24 160 14x30RA30 30 180 16x38

Tool Overall Section length of tool

RA16d 115 12,3x3x2RA19d 130 14,5x4x2,6RA22d 140 16x4,2x2,7RA24d 145 19x4,5x2,8RA30d 160 22x5x3

Seegerring tool suitable for RA22RA14d -,-- seegerring available:0,9 - 1,10 - 1,30 - 1,60 - 1,85 - 2,152,15 - 2,65 - 3,15 - 4,15 - 5,15For using RA14d tool 0,9 - 2,15useadaptor for RA22 ====>> RA14d-E

VA - FLEXIBLE PARTING-OFF TOOL/HOLDERThis toolholder is made of a superior spring-steel.It has thefollowing convincing advantages:

1. Owing to the slot in the head of the toolholder the parting-offtool is adequately flexible.

2. The well known chattering is eliminated.

3. The springing keeps the workpiece from running into the tooland consequently eliminates the causes of the majority ofbreakages in parting-off tools.

4. The tool is “backed off” lengthwise.

Holder level of Cuttingedge Length SectionVA12 12 115 10X13VA16 16 150 13X22VA20 20 195 15,5X27VA25 25 220 18,8X35

Tool Length SectionVA12d 100 10,0x2,5x2,0VA16d 125 14,5x3,0x2,0VA20d 150 19,0x3,5x2,2VA25d 150 22,0x3,5x2,2


Holder Level of cuttingedge Length SectionSW16 16 130 17x19SW20 20 130 18x25

Tool Length SectionSW16d 125 16x4,0x2,6SW20d 150 20x4,5x3,1

SW - PARTING-OFF TOOL/HOLDERThe SW parting-off tool/holder has been made very rigid inorder to reduce vibrations to a minimum.

The SW tools are ground HIGHLY BICONICALLY, whichensure that materials which are difficult to be machinedare cut off extremely well.

VD - FLEXIBLE THREADING TOOL/HOLDERThe VD holder is extremely suited for thread-cutting in any material.The springing head prevents the tool from clogging. The level of thecutting edge and the lead angle can be adjusted over a wide range,without removing the tool.If the point off the tool has become dull, only the top is to bere-grind.

DO NOT GRIND A TOP RAKE, OR IN THE FLANKS !

Holder level of Cuttingedge Length SectionVD14 14 120 16X16VD16 16 140 16X22VD20 20 170 20X29VD24 24 220 25X32

Tool 55º OR 60º Length SectionVD14d.. 33 3,5x7x18VD16d.. 45 3,5x7x18VD20d.. 55 5x9,5x23VD24d.. 65 6x11,5x25

EM - TOOLBIT holderOther toolbits can be exchanged without unclamping the holder.

In this holder the boring tools with 8mm diameter shanks can beclamped (VB3 - VB12 see page 4).

Holder Level of cutting edge Overall length Section of holder / shankEM14 14 120 12x20

Tool ==> EM14DVR EM14DVL EM14DMR EM14DML EM14DP EM14D60 EM14DALength 55 55 55 55 55 55 55Section 10X10 10X10 10X10 10X10 10X10 10X10 10X10

Tool ==> AM10DVR AM10DVL AM10DMR AM10DML AM10DP AM10D60 AM10DALength 55 55 55 55 55 55 55Section 10X10 10X10 10X10 10X10 10X10 10X10 10X10

Also available as set in wooden case.Toolsetnr. AS10VOL(BH6+AM10D serie+ VB7D-B-60-55-KToolsetnr. AS14VOL(EM14+EM14D serie+ VB9D-B-60-55-K

VR =rough-turning tool RH. VL =rough-turningtool LH.MR =knife tool RH ML =knife tool LHP =single point tool 80º 60 =threading tool 60ºA =parting off tool

For round turning toolbits use toolholder type BH6(page 5)


TR - TOOLBIT HOLDERThe tool is at an angle of 3º in the holder.It is advisable to use a long toolbit in the holder, so thatwastage is minimized.As compared with butt-welded tools this combinationeffects a very large saving.

Holder Level of cutting edge Length Section Suitable for toolbitTR12 12 110 10,0x12 5x5x 63TR14 14 125 11,0x18 6x6x100TR16 16 145 12,5x20 8x8x160TR20 20 165 14,0x26 10x10x160TR23 23 180 16,0x30 12x12x160

BH - FIXED BORING TOOL/HOLDERThese holders and tools are particularly suited for precisionturning. They are in service in practically all kinds oflaboratories and mechanical workshops.

Holder Level of cutting edge Overall length Section of holder BoringBH6 6 100 12x12 8 mm both sideBH8 7,5 125 15x15 8mm and 10 mm

VBH - ADJUSTABLE BORING TOOL/HOLDERThe VBH adjustable boring holder is suited for all VB fixed boring tools.The level of the cutting edge is adjustable between 9mm and 21mmwithout unclamping the holder. To be used for boring tool VB3-VB14.

Holder Level of cutting edge Overall length Section shankVBH18 9 through 21 120 9,5x16

VB - FIXED BORING TOOLThe VBH adjustable boring holder is suited for all VB fixed boring tools.The level of the cutting edge is adjustable between 9mm and 21mmwithout unclamping the holder. To be used for boring tool VB3-VB14.

D -BORINGTOOLS FOR THROUGH HOLESB -BORINGTOOLS FOR BLIND HOLES60º -INSIDE THREADING TOOL55º -INSIDE THREADING TOOLK -INTERNAL RECESSING TOOLS -INTERNAL GROOVING TOOL

ALL VB BORING TOOLS ARE DELIVERABLEWITH EXTENDED SHANKS. ( TYPE VS)

Tool Version types Length Length Section of shank min boring Type K Type S normal type VS type diameter width-depth width-depth

VB3…. D-B 60 125 8 3 - -VB5….. D-B-60º-55º 60 125 8 5 - -VB7…. D-B-60º-55º-K-S 65 125 8 7 2x2 1,1x2VB9…. D-B-60º-55º-K-S 75 125 8 9 2,4x2,4 1,1x2,4VB12… D-B-60º-55º-K-S 80 125 8 12 2,7x2,7 1,1x2,7VB14… D-B-60º-55º-K-S 95 125 10 14 3x2 1,1x3

Example of ordering: holder 3 pcs. BH8 / tool 5 pcs. VB12-B or 5 pcs. VB12-BVS


DETACHABLE BORING TOOL/HOLDERThe detachable boring tools should be properly tightened down tothe shoulder of the boring rods.

In this split boring toolholder the boring rod can beset to the boring depth to reduce vibrations to a minimum.

Holder -----------------------> BH10 BH14 BH14 BH20 BH20 BH24 BH24 BH28*Level cutting edge 10 14 14 20 20 23,5 23,5 27,5Overall length 110 150 150 180 180 210 210 210Section of holder 20x20 23x28 23x28 30x40 30x40 42x47 42x47 47x55Boring rod -----------------> BST14 BST18 BST22 BST26 BST30 BST35 BST44* BST54*Length excl.thread 165 190 245 275 325 375 385 450Section rodshank 10 13 13 20 20 28 28 32Tool D-B-60-55-K-S -----> AB14.. AB18.. AB22.. AB26.. AB30.. AB35.. AB44..* AB54..*Length D,B-60,55,K-S 21-18-15 25-22-18 28-24-21 32-26-22 36-31-26 43-35-29 47-40-33 55-45-38To be used for boringof …..mm and over 14 18 22 26 30 35 44 54Width and depth K 3x3 3,5x3,5 4x4 4,5x5 6x6 8x6,5 9x8 10x11Width and depth S 1,1x3 1,3x3 1,6x4 1,85x5 2,15x6 2,65x6 3,15x8 4,2x11*= outselling product * All types deliverable with carbide tipExample of ordering 3x AB14D 1x BST14 1x BH10

ASSORTIMENT CASEAS16VOLHR16-HR16d-HM16-HM16dVA16-VA16d-RA16-RA16dVD16-VD16d60-VD16d55VBH18 - Inbuskey 3mmVB9D-B-60-55-KVB14D-B-60-55-KBH14-BST22-AB22D-B-60-55-K

AS20VOLHR20-HR20d-HM20-HM20dVA20-VA20d-RA20-RA20dVD20-VD20d60-VD20d55VBH18 - Inbuskey 3mmVB9D-B-60-55-KVB14D-B-60-55-KBH20-BST30-AB30D-B-60-55-K


TOOLBITS HSCo 1.3207 Hrc.66 9% Co

Ref. size Ref. size Ref. size Ref. size4x4x63 7x7x200 10x10x100 14x14x2005x5x63 8x8x63 10x10x160 16x16x2006x6x63 8x8x100 10x10x200 18x18x2006x6x100 8x8x160 12x12x100 20x20x2006x6x160 8x8x200 12x12x160 25x25x2006x6x200 10x10x63 12x12x200 32x32x200

Ref. size Ref. size Ref. size Ref. size2x50 4x100 10x100 18x2002x100 5x100 10x160 20x2002,5x50 6x100 10x200 22x2002,5x100 6x160 12x100 25x2003x100 7x160 12x200 30x2003,5x100 8x100 14x2004x63 8x160 16x200

Ref. size Ref. size Ref. size Ref. size6x4x100 10x6x200 12x10x200 20x10x2008x2x100 10x8x200 14x6x200 20x12x2008x4x100 12x3x100 14x8x200 20x15x20010x3x100 12x5x100 15x10x200 25x10x20010x4x100 12x6x160 16x8x200 25x12x20010x5x100 12x6x200 16x10x200 25x20x20010x6x100 12x8x200 20x6x200 32x20x200

KEYWAY TOOLBITS HSCo 1.3207 Hrc.66 9% Co with + tolerance

Ref. size Ref. size Ref. size Ref. sizeSP4x4x100 SP6X6X100 SP10X10X100 SP14X14X100SP5X5X100 SP8X8X100 SP12X12X100 SP16X16X100


SELECTION CHART OF CUTTING SPEEDS FOR HIGH-SPEED STEEL

Cuttingspeed in m/min.Material to be machined at V240 Back-off angle Top rake angle

Rough- and finish-turning

Carbon steel34-50 30 - 50 - 80 5° - 8° 6° - 15°50-60 22 - 40 - 60 4° - 8° 6° - 12°60-70 19 - 32 - 45 5° - 8° 6° - 12°70-85 15 - 26 - 38 5° - 8° 6° - 10°85-100 12 - 20 - 30 5° - 8° 6° - 8°

Alloy steel70-85 14 - 22 - 35 5° - 8° 6° - 8°85-100 12 - 18 - 28 5° - 8° 4° - 6°100-140 10 - 16 - 22 5° - 8° 0° - 4°140-180 8 - 12 - 18 5° - 8° 0° - 4°

Cast steel30-50 20 - 30 - 42 5° - 8° 0° - 6°50-70 16 - 24 - 34 5° - 8° 0° - 6°

Materials short chipsCast iron < 200 Brinell 18 - 25 - 35 5° - 8° 0° - 4°Cast iron > 200 Brinell 10 - 15 - 22 5° - 8° 0° - 2°Brass 120 - 150 - 200 5° - 8° 0° - 6°Bronze 40 - 80 - 100 5° - 8° 0° - 4°

Light materialsAluminium < 50 Brinell 150 - 300 - 450 10°-12° 15° - 30°Silumin (12-14% Sil.) 30 - 70 - 120 5° - 8° 5° - 10°Alusil(18-22% Sil.) 20 - 35 - 60 5° - 8° 5° - 10°

Directions for use

The diagonal which intersects the lineof the cutting speed and the lineof the diameter denotes the number ofrevolutions per minute.

Example: Diameter is 40mmCuttingspeed is 80 m/min

Result: 640 RPM(see dashed line)

KIM Komeetstaal BRAZED CARBIDE TOOLS Catalogue 2008 Page 10

ISO 1 STRAIGHT ROUGHING TOOL AVAILABLE in R.H. and L.H. version (Picture shows R.H.)

Article code Section/length Article code Section/length7100R/L 10x10x100 7103R/L 20x20x1607101R/L 12x12x110 7104R/L 25x25x2007102R/L 16x16x140

Article code Section/length Article code Section/length7200R/L 10x10x100 7203R/L 20x20x1607201R/L 12x12x110 7204R/L 25x25x2007202R/L 16x16x140

ISO 2 BENT ROUGHING TOOL AVAILABLE in R.H. and L.H. version (Picture shows R.H.)

ISO 4 FORM TOOL

Article code Section/length Article code Section/length7601 12x12x110 7603 20x20x1607602 16x16x140

ISO 5 FACING TOOL AVAILABLE in R.H. and L.H. version (Picture shows R.H.)

Article code Section/length Article code Section/length7902R/L 16x16x100 7904R/L 25x25x2007903R/L 20x20x160

ISO 6 KNIFE TOOL AVAILABLE in R.H. and L.H. version (Picture shows R.H.)

Article code Section/length Article code Section/length8000R/L 10x10x100 8003R/L 20x20x1608001R/L 12x12x110 8004R/L 25x25x2008002R/L 16x16x140 8005R/L 32x32x250

ISO 7 PARTING-OFF TOOL AVAILABLE in R.H. and L.H. version (Picture shows R.H.)

Article code Section/length Width of cut Depth of cut8100R/L 10x16x125 4 128101R/L 12x20x140 5 168102R/L 16x25x180 6 208103R/L 20x32x220 8 258104R/L 25x40x280 10 32

ISO 8 BORING TOOL for through holesArticle code Section/length Length Ø Min hole Ø7300 10x10x150 50mm 15mm7301 12x12x180 63mm 18mm7302 16x16x210 80mm 23mm7303 20x20x250 100mm 29mm7304 25x25x300 125mm 37mm

Article code Section/length Length Ø Min hole Ø7300RO 10X150 150mm 15mm7301RO 12X180 180mm 18mm7302RO 16X210 210mm 23mm7303RO 20X250 250mm 29mm7304RO 25X300 300mm 37mm

ISO 8 BORING TOOL for through holes round schank type

ISO grades P20-P30-P40-M20-K10-K20









ISO 9 Boring tool for blind holesArticle code Section/length Width of cut Depth of cut7400 10x10x150 50mm 13mm7401 12x12x180 63mm 16mm7402 16x16x210 80mm 21mm7403 20x20x250 100mm 26mm7404 25x25x300 125mm 32mm7405 32x32x355 160mm 40mm


ISO 9 Boring tool for blind holes round type 74RO


Article code Section/length Length Ø Min hole Ø7400RO 10x150 150mm 13mm7401RO 12x180 180mm 16mm7402RO 16x210 210mm 21mm7403RO 20x250 250mm 26mm7404RO 25x300 300mm 32mm

SINGLE POINT TOOL 80º type 75

Article code Section/length Article code Section/length7500 10x10x100 7503 20x20x1607501 12x12x110 7504 25x25x2007502 16x16x140 ISO grades P20-P30-P40-M20-K10-K20

Article code Section/length Article code Section/length7500.55or 60 10x10x100 7503.55or 60 20x20x1607501.55or 60 12x12x110 7504.55or 60 25x25x2007502.55or 60 16x16x140

OUTSIDE THREADING TOOL 60º or 55º type 75


Article code Section/length Length Ø Min hole Ø8200 10X10X125 32mm 16mm8201 12X12X140 40mm 19mm8202 16X16X180 50mm 24mm8203 20X20X220 80mm 29mm8204 25X25X250 100mm 35mm

INSIDE THREADING TOOL 60º or 55º type 82



Article code Section/length Width of cut Min hole Ø8300 10X10X125 3 16mm8301 12X12X140 3,5 19mm8302 16X16X180 4 24mm8303 20X20X220 5 29mm8304 25X25X250 6 35mm

INTERNAL RECESSING TOOL type 83

VEE PULLEY GROOVING TOOL type 85 Standard angle 38º

ISO grades K20

Article code Section/length Front width Angle º 8512 12x12x110 3,1 388516 16x16x140 4,1 388520 20x20x160 5,3 388525 25x25x200 6,8 38


ISO division —> Group P Group MMax. feed mm/rev. —> 0,8 1,5 3 1,5Grade of carbide —> P20 P30 P40 M20

Tens ile Back- Top White Brown Orange GreenMaterial to be m achined strength off rake

kg/m m 2 angle angle Cutting speeds in m/min.Rough + finish Rough + finish Rough + finish Rough + finish

Carbon steel turning turning turning turningSt41 < 50 5-10º 6-16º 120-180-250 100-150-220 50-75-100 100-150-200St60 50-70 5-8º 6-12º 100-150-220 80-120-180 40-60-80 80-120-180St70 70-85 5-8º 6-10º 80-120-180 60-100-150 30-40-60 60-100-150St85 85-100 0-8º 6-8º 60-100-140 40-70-100 20-30-50 40-70-100Cast steel (use P30 or M20 for impure materials)Stg 40 < 50 5-8º 0-6º 80-140 80-120 30-50-70 40-80-120Stg 50 50-65 5-8º 0-6º 70-120 60-100 20-40-60 30-60-100Stg 65 and harder >65 5-8º 0-6º 50-100 40-80 15-30-50 20-50-80Malleable cas t iron 5-8º 4-8º 50-80-120 50-90-120Alloy steelHeat-treated s teel 70-85 5-8º 6-8º 60-100-150 50-80-120 25-40-60 50-80-120Heat-treated s teel 85-100 5-8º 4-6º 50-70-110 40-60-80 15-30-50 40-60-80Heat-treated s teel 100-140 5-8º 0-4º 25-50-75 25-40-60 15-25-40 25-40-60Heat-treated s teel 140-180 5-8º -4 + 2º 20-40-60 20-30-50 10-20-30 20-30-50Annealed tool s teel 50-80 5-8º 0-6º 80-120-180 60-100-150 30-40-60 60-100-150Stainless steelType 18% Cr. - 8% Ni 7-10º 6-10º 20-40-60 40-60-80Type 12-15% Cr. Low C content 5-8º 6-10º 100-140-180 80-120-140 50-70-100 80-120-140Type 17-18% Cr. Low C content 5-8º 6-10o 100-140-180 80-120-140 50-70-100 80-120-140Type 12-15% Cr. Low C content 4-8º 4-8º 90-120-160 60-90-120 30-50-70 60-90-120Manganesesteel app. 12% Mn 4-6º -6 + 6º 5-15-30Hardened s teel 4-6º 0º 10-30-40ISO division —> Group K Group MGrade of carbide —> K10 K20 M20

Tens ile Back- Top Yellow/green Yellow GreenMaterial to be m achined strength off rake

kg/m m 2 angle angle Cutting speeds in m/min.Cast ironCast iron soft <200 4-8º 6-10º 60-100-140 60-100-120 45-75-110Cast iron hard >200 4-8º 0-6º 50-100-120 40-80-100 30-55-90Cast iron, alloyed 200-400 4-8º 0-6º 30-50-90 20-40-70 15-30-60Chilled iron <500 3-5º -2 + 2º 6-10-2015 5-9-2012Chilled iron >500 3-5º 0º 2-5-2008Non-ferrous-materialsCopper 6-8º 20-30ºCollector bronze 5-7º 10-15º 200-400 175-350Phosphor bronze 6-8º 6-10º 200-250-350 150-200-300Brass 6-8º 8-12º 250-300-400 200-350-350Lightmetal m anganese alloy 80-100 8-10º 5-10º 150-300-450 150-300-450Duralumin 100-130 6-8º 5-10º 100-250-350 100-250-350Silum in 12-14% St. 6-8º 5-10º 100-200-300 80-150-250 80-150-250

Schank Range of application Carbidecolour Acc. To ISOWhite From light to heavy turning of steel and cast steel at high cutting speeds, P20

medium feeds and favourable operating conditions.Braun Rough-turning of steel and cast steel at relatively high cutting speeds P30

and adverse operating conditions.Orange Rough-turning of steel and cast steel at low speeds and very adverse P40

operating conditions, such as with irregular material, a rough surface,varying depth of cut, shock loads and vibrations (chattering).Suitable for turning stainless steel.

Green Suitable as a general-purpose material. The machining of all kinds of steel, M20cast steel and cast iron. Relatively high cutting speeds.

Yellow Wear-resistant grade for rough- and finishing turning of cast iron K10(with a green band) with a hardness of up to approximately 350 Brinell

Yellow Wear-resistant grade for rough- and finishing turning of cast iron K20with a hardness of up to approximately 250 Brinell, non ferrous materials etc.

Tool right Tool left Section HxWxL201.2516 202.2516 25x16x200201.3220 202.3220 32x20x250201.4025 202.4025 40x25x315

Tool right Tool left Section HxWxL205.1616 206.1616 16x16x140205.2020 206.2020 20x20x160205.2525 206.2525 25x25x200205.3232 206.3232 32x32x250205.2516 206.2516 25x16x200205.3220 206.3220 32x20x250205.4025 206.4025 40x25x315

STRAIGHT ROUGHER 45ºType 201/202

KIM Komeetstaal butt welded HSCo tools Catalogue 2008 Page 13

STRAIGHT ROUGHER 15ºType 205/206

STRAIGHT ROUGHER 15º shortType 105/106

Tool right Tool left Section HxWxL105.1616 106.1616 16x16x140105.2020 106.2020 20x20x160105.2525 106.2525 25x25x200

Tool right Tool left Section HxWxL213.1010 214.1010 10x10x100213.1212 214.1212 12x12x110213.1616 214.1616 16x16x140213.2020 214.2020 20x20x160213.2525 214.2525 25x25x200213.2516 214.2516 25x16x200213.3220 214.3220 32x20x250213.4025 214.4025 40x25x315

BENT ROUGHER 45ºType 213/214


BENT ROUGHER 45º shortType 113/114Tool right Tool left Section HxWxL113.1010 114.1010 10X10X90113.1212 114.1212 12X12X100113.1616 114.1616 16X16X110113.2020 114.2020 20X20X125113.2525 114.2525 25X25X140

Tool right Tool left Section HxWxL-bxl249.1010 250.1010 10x10x00-2x10249.1212 250.1212 12x12x110-2,5x10249.1610 250.1610 16x10x140-3x12249.2012 250.2012 20x12x160-4x16249.2516 250.2516 25x16x200-5x20249.3220 250.3220 32x20x250-6x25249.4025 250.4025 40x25x315-8x32

PARTING OFF TOOLType 249/250

PARTING OFF TOOL SHORTType 149Tool right Section HxWxL-bxl149.1010 10x10x90-2x10149.1212 12x12x100-2,5x10149.1610 16x10x110-3x12149.2012 20x12x125-4x16149.2516 25x16x140-5x20149.3220 32x20x170-6x25

GROOVING TOOLType 255/256

Tool right Tool left Section HxWxL-bxl255.2012 256.2012 20x12x160-8x12255.2516 256.2516 25x16x200-10x16255.3220 256.3220 32x20x250-12x20255.4025 256.4025 40x25x315-6x25

GROOVING TOOL SHORTType 155

Tool right Section HxWxL-bxl155.1610 16x10x110-6x10155.2012 20x12x125-8x12155.2516 25x16x140-10x16


DIAMOND NOSE TOOLType 227

DIAMOND NOSE TOOLType 127

KNIFE TOOL Type 237/238

KNIFE TOOL Type 137/138

SIDE TOOL Type 239/240

Tool Section HxWxL227.1212 12x12x110227.1616 16x16x140227.2020 20x20x160227.2525 25x25x200227.2516 25x16x200227.3220 32x20x250

Tool right Section HxWxL127.1212 12x12x100127.1616 16x16x110127.2020 20x20x125127.2525 25x25x140

Tool right Tool left Section HxWxL237.1010 238.1010 10x10x100237.1212 238.1212 12x12x110237.1616 238.1616 16x16x140237.2020 238.2020 20x20x160237.2525 238.2525 25x25x200Tool right Tool left Section HxWxL237.1610 238.1610 16x10x140237.2012 238.2012 20x12x170237.2516 238.2516 25x16x200237.3220 238.3220 32x20x250237.4025 238.4025 40x25x315

Tool right Tool left Section HxWxL137.1010 138.1010 10x10x90137.1212 138.1212 12x12x100137.1616 138.1616 16x16x110137.2020 138.2020 20x20x125137.2525 138.2525 25x25x140137.1610 138.1610 16x10x110137.2012 138.2012 20x12x125137.2516 138.2516 25x16x140

Tool right Tool left Section HxWxL239.1212 240.1212 12x12x110239.1616 240.1616 16x16x140239.2020 240.2020 20x20x160139.2525 240.2525 25x25x200239.2012 240.2012 20x12x160239.2516 240.2516 25x16x200239.3220 240.3220 32x20x250


SIDE TOOLType 139/140

SQUARE NOSE FINISHING TOOLType 225

EXTERNAL THREADING TOOLType 187.55/189.60

SWAN-NECKED PARTING OFF AND GROOVING TOOLType 163/263/164/264

Tool right Section HxWxL139.1616 16x16x110139.2020 20x20x125139.2525 25x25x140

Tool Left Section HxWxL140.1616 16x16x110140.2020 20x20x125140.2525 25x25x140

Tool Section HxWxL225.2020 20x20x160225.2525 25x25x200225.2516 25x16x200225.3220 32x20x250225.4025 40x25x315

Tool 55º Tool 60º Section HxWxL187.1010 189.1010 10x10x90187.1212 189.1212 12x12x100187.1610 189.1610 16x10x110187.2012 189.2012 20x12x125187.2516 189.2516 25x16x140187.3220 189.3220 32x20x170

Tool Right Tool Left Section HxWxL-bxl163.2020 164.2020 20x20x140-6x40163.2525 164.2525 25x25x170-8x50163.2012 - 20x12x125-5x32163.2516 - 25x16x140-6x40263.2516 264.2516 25x16x220-6x40263.3220 264.3220 32x20x280-8x50


SIDE BORING TOOL Type 171

FACE BORING TOOL Type 173

RECESSING TOOL Type 175

THREADING TOOLType 181 55º / 185 60º

BORING TOOLHOLDER Type 180

Tool Section DxL171.6 6x100171.8 8x125171.10 10x150171.12 12x180171.16 16x210171.20 20x250171.25 25x300171.32 32x355

Tool Section DxL173.6 6x100173.8 8x125173.10 10x150173.12 12x180173.16 16x210173.20 20x250173.25 25x300173.32 32x355

Tool Section DxL bxl175.6 6x100-3x4175.8 8x125-4x5175.10 10x150-5x6175.12 12x180-6x8175.16 16x210-8x10175.20 20x250-10x12175.25 25x300-12x16175.32 32x355-16x20

Tool 55º Tool 60º Section DxL bxl181.6 185.6 6x110-3x4181.8 185.8 8x125-3x5181.10 185.10 10x150-3x6181.12 185.12 12x180-4x8181.16 185.16 16x210-5x10181.20 185.20 20x250-6x12181.25 185.25 25x300-8x16

Tool Section DxWxL180.6 6x10x70180.8 8x12x80180.10 10x14x85180.12 12x16x90180.16 16x20x100180.20 20x25x110180.25 25x32x125


SWAN-NECKED PLANING TOOLS (OUTSELLING PRODUCT)

Tool righthand Tool lefthand Section HxBxL bxl401.3220 402.3220 32x20x320407.3220 32x20x320425.3220 32x20x320449.4025 40x25x400 - (449) 12x50449.5032 50x32x500 - (449) 16x63

Tool H B L b L1 U C+0,05

-076003 20 12 250 3 40 5 2076004 20 12 250 4 40 5 2076005 20 12 250 5 40 5 2076006 25 16 300 6 50 6 2576008 25 16 300 8 50 6 2576010 32 20 350 10 60 8 3076012 32 20 350 12 60 8 30

SLOTTER TOOL (OUTSELLING PRODUCT)

Documents

High speed steel Carbide tools Bud welded · KIM Komeetstaal HIGH-SPEED-STEEL TOOL/HOLDERS Catalogue 2008 Page 4 Holder Level of cuttingedge Length Section SW16 16 130 17x19 SW20