Upload
jprakashus
View
253
Download
0
Embed Size (px)
Citation preview
7/27/2019 Level Instrument manual
1/36
D
E
F
KA180F/00/a3/12.0652010984
SchwimmschalterFTS20
FllstandgrenzschalterLevel Limit Switch
Dtecteur de niveau
7/27/2019 Level Instrument manual
2/36
2 Endress + Hauser
D
Sicherheitshinweise
Der Schwimmschalter FTS20 darf nur als Fllstandgrenzschalter in geeigneten Flssigkeiteneingesetzt werden. Bei unsachgemem Einsatz knnen Gefahren von ihm ausgehen.Das Gert darf nur von qualifiziertem und autorisiertem Personal unter besonderer Beachtung dieser Kompaktanleitung, der einschlgigen Normen, der gesetzlichen Vorschriften und der Zertifikate (je nach Ausfhrung und Anwendung)
eingebaut, angeschlossen und in Betrieb genommen werden.
Sicherheitssymbole
# Warnung!Warnung deutet auf Aktivitten oder Vorgnge, die wenn sie nicht ordnungsgem durchgefhrtwerden zu Verletzungen von Personen oder zu einem Sicherheitsrisiko fhren knnen. BeachtenSie die Arbeitsanweisungen genau und gehen Sie mit Sorgfalt vor.
!Hinweis!Hinweis deutet auf Vorgnge, die wenn sie nicht ordnungsgem durchgefhrt werden einen Einfluss auf den Betrieb haben oder eine unvorhergesehene Gertereaktion auslsen knnen.
7/27/2019 Level Instrument manual
3/36
Endress + Hauser 3
D
Gertevarianten
Bestellcode Kabellnge Schaltertyp
N
A
M
U
R
Initiator mit Schaltkugel fr den Einsatz im Ex-Bereich2-Leiter nach EN 60947-5-6 (NAMUR)Einsatz mit Trennverstrker; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
mit Kabelmaterial PVC (fr Wasser, Abwasser)
5201012071035517
5 m20 m
mit Kabelmaterial PUR (fr Kraftstoffe und le)
5201012171035518
5 m20 m
mit Kabelmaterial CSM (fr Suren und Laugen)
A
C
/
D
C
Mikroschalter mit Schaltkugel fr den Standardeinsatz,
3-Leiter, Wechsler fr max. 250 V AC / 150 V DC5201012271035520
5 m20 m
mit Kabelmaterial PVC (fr Wasser, Abwasser)
5201012371035521
5 m20 m
mit Kabelmaterial PUR (fr Kraftstoffe und le)
5201012471035522 5 m20 m mit Kabelmaterial CSM (fr Suren und Laugen)
Zubehr
Nivotester FTL325N Trennschaltverstrker
7/27/2019 Level Instrument manual
4/36
4 Endress + Hauser
DFunktion
Ein im Schwimmschalter eingebautes Schaltelement schaltet bei Abweichung aus der Waagerechten.
Der Schaltvorgang wird durch die Bewegung einer Stahlkugel ausgelst und je nach Ausfhrung
durch einen induktiven Initiator oder einen Mikroschalter ausgefhrt.Als Schaltausgang stellt der induktive Initiator ein Schaltsignal nach EN 60947-5-6 (NAMUR) zur Ver-fgung. Die Ausfhrung mit Mikroschalter einen Wechselkontakt.
Merkmale
sichere Grenzwerterfassung von Fllstnden in Flssigkeiten elektrische Anschlsse nach NAMUR fr den Ex-Bereich (bis Zone 1) oder Wechsler (AC/DC)
fr den universellen Standardeinsatz verschiedene Kabelmaterialien fr unterschiedliche Medien kleiner Durchmesser fr einfache Montage durch Gewindebohrung G1A
52010125 Stopfbuchsverschraubung G1A, PVC
52010126 Gegenmutter G1A, PVC
52010127 Beschwerungsgewicht (Polyamid beschichtet)
7/27/2019 Level Instrument manual
5/36
Endress + Hauser 5
D
Anwendungen
Pumpen und Ventile mit einem Schalter steuern oder Fllstandhhe bzw. -grenze signalisieren
7/27/2019 Level Instrument manual
6/36
6 Endress + Hauser
D
Einbau
Der Schwimmschalter kann wie folgt montiert werden: Der Schwimmschalter kann von auen durch eine Gewindebohrung G1A in den Behlter
eingefhrt und mit der Stopfbuchsverschraubung (G1A) verschraubt werden Bei Montage von oben sollte das Beschwerungsgewicht verwendet werden
! Hinweis! Der Drehpunkt des Kabels soll immer waagerecht liegen
Die Kabellnge zwischen Befestigung und Schwimmkrper ist abhngig vom Kabeltyp(siehe Technische Daten)
Bei Verwendung des Beschwerungsgewichtes mu hinter der Stopfbuchsverschraubung auf der Auenseite des Behlters eine zustzliche Zugentlastung (z.B. ein Knoten im Kabel)angebracht werden
7/27/2019 Level Instrument manual
7/36
Endress + Hauser 7
D
Elektrischer Anschluss
# Warnung!
Beachten Sie den Schaltertyp!
Initiator mit Schaltkugel(NAMUR)Bestellcodes:52010119, 5201012052010121, 7103551671035517, 71035518
AnschlusskennungL+ = Schwarz oder BraunL- = Blau
(Schlieend beim Aufschwimmen)
Wechselkontakt(AC/DC)Bestellcodes:
52010122, 5201012352010124, 7103552071035521, 71035522
Kabelfarben:Schwarz + Braun = Kontakt geffnet
Schwarz + Blau = Kontakt geschlossen(Kontaktelage beim Aufschwimmen)
7/27/2019 Level Instrument manual
8/36
8 Endress + Hauser
D
Technische Daten FTS20 (NAMUR)
Messsystem Bestehend aus Schwimmschalter FTS20 und einem Trennschaltverstrker,z.B. Endress+Hauser Nivotester FTL325N
Schaltelement Induktiver Nherungsschalter mit Schaltkugel, aufschwimmend schlieendHilfsenergie 8,2 V 2 V
Betriebsstrom 2,1 mA geschaltet
Verpolschutz Ja
Schaltwinkel Schaltpunkte oben/unten 12, gegen die Waagerechte gemessen
Umgebungstemperatur Abhngig vom Kabelmaterial;PVC, PUR und CSM: -20 +70 C
Schutzart DIN EN 60529, IP68 (20 m untertauchen / zeitlich ohne Begrenzung)
Umgebungsdruck 3 bar
Dichte Schwimmschalter 0,8 g/cm3
Material Schwimmkrper Polypropylen (PP)
Material Kabel PVC, CSM: Standardlngen 5 m und 20 m, Querschnitt 2 x 0,75 mm2PUR: Standardlngen 5 m und 20 m, Querschnitt 2 x 0,50 mm2
Einsatzbereiche und Mindest-kabellnge zwischen Befesti-gung und Schwimmkrper
PVC: 50 mm, bevorzugt fr Wasser, Schmutzwasser, leicht aggressive MedienPUR: 100 mm, bevorzugt fr Kraftstoffe, Heizle, lhaltige FlssigkeitenCSM: 100 mm, bevorzugt fr Suren und Laugen
Ex-Zulassung TV 01 ATEX 1709
Ex-Schutzart 0 II 2G EEx ia II B T5
Ex-Daten T5 (Ta = 70 C) T4 (Ta = 70 C)Spannung Ui 16 V 16 VStrom Ii 52 mA 72 mALeistung Pi 180 mW 242 mWInduktivitt Li 1 mH 1 mH
Kapazitt Ci 153 nF 153 nF
7/27/2019 Level Instrument manual
9/36
Endress + Hauser 9
D
Technische Daten FTS20 (AC/DC)
Normen EN 60947-5-2, EN 50014:1997, EN 50020:1994
Messsystem bestehend aus einem Schwimmschalter FTS20
Schaltelement Mikroschalter mit Schaltkugel
Schaltfunktion Wechsler
Schaltspannung AC: max. 250 V; DC: max. 150 V
Schaltstrom max. 3 A (AC), max. 1 A (DC)
Schaltwinkel oberer Schaltpunkt: + 25 6,unterer Schaltpunkt: +14 3, gegen die Waagerechte gemessen
Umgebungstemperatur abhngig vom Kabelmaterial;PVC: +5 +70 C, PUR und CSM: -20 +85 C
Schutzart DIN EN 60529, IP68 (20 m untertauchen / zeitlich ohne Begrenzung)
Umgebungsdruck 3 barDichte Schwimmschalter 0,8 g/cm3
Material Schwimmkrper Polypropylen (PP)
Material Kabel PVC, CSM: Standardlngen 5 m und 20 m, Querschnitt 2 x 0,75 mm2
PUR: Standardlnge 5 m und 20 m, Querschnitt 2 x 0,50 mm2
Einsatzbereiche und Mindest-kabellnge zwischen Befesti-gung und Schwimmkrper
PVC:
50 mm, bevorzugt fr Wasser, Schmutzwasser, leicht aggressive MedienPUR: 100 mm, bevorzugt fr Kraftstoffe, Heizle, lhaltige FlssigkeitenCSM: 100 mm, bevorzugt fr Suren und Laugen
7/27/2019 Level Instrument manual
10/36
10 Endress + Hauser
D
Abmessungen
Schwimmschalter FTS20
Stopfbuchsverschraubung Beschwerungsgewicht
(Mae in mm)
135
29,
2
G1A
SW 41
190
32,5
7/27/2019 Level Instrument manual
11/36
Endress + Hauser 11
D
7/27/2019 Level Instrument manual
12/36
12 Endress + Hauser
D
7/27/2019 Level Instrument manual
13/36
EE
KA180F/00/en/12.0652010984
Floating SwitchFTS20
FllstandgrenzschalterLevel Limit Switch
Dtecteur de niveau
7/27/2019 Level Instrument manual
14/36
2 Endress + Hauser
E
Safety instructions
The FTS20 floating switch may only be used as a level limit switch in suitable liquids.Improper use may cause dangerous situations.
The instrument may only be installed, connected and commissioned by qualified andauthorised personnel, paying particular attention to: this compact manual the appropriate standards the statutory regulations and
certificates (depending on version and application)
Safety symbols
# Warning!Warning indicates an action or procedure which, if not performed correctly, can result ininjury or a safety hazard. Read the instructions thoroughly and proceed carefully.
! Note!"Note" indicates processes which if improperly executed could affect operation or trigger
unexpected instrument actions.
7/27/2019 Level Instrument manual
15/36
Endress + Hauser 3
E
Instrument variants
Order Code Cable length Type of switch
N
A
M
U
R
Initiator with switching ball for use in explosion-hazardous areas2-wire to EN 60947-5-6 (NAMUR)Use with isolating amplifier; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
With PVC cable material (for water, wastewater)
5201012071035517
5 m20 m
With PUR cable material (for fuels and oils)
5201012171035518
5 m20 m
With CSM cable material (for acids and alkalis)
A
C
/
D
C
Microswitch with switching ball for standard application,
3-wire, change-over contact for max. 250 V AC / 150 V DC
5201012271035520
5 m20 m
With PVC cable material (for water, wastewater)
5201012371035521
5 m20 m
With PUR cable material (for fuels and oils)
5201012471035522 5 m20 m With CSM cable material (for acids and alkalis)
Accessories
Nivotester FTL325N Isolating amplifier
7/27/2019 Level Instrument manual
16/36
4 Endress + Hauser
E
FunctionAn element built into the floating switch switches when a deviation in the horizontal is detected.The switching process is triggered by the movement of a steel ball and, depending on the version,is carried out by an inductive initiator or a microswitch.The inductive initiator acts as a switching output and provides a switching signal to EN 60947-5-6
(NAMUR). The microswitch version is a two-way switch.
Features
Reliable level limit detection in liquids
Electrical connections to NAMUR for hazardous areas (to Zone 1) or change-over contact(AC/DC) for universal standard application Different cable materials for different media Small diameter for simple installation using tapped hole G1A
52010126 Counter nut G1A, PVC
52010127 Weight (coated with polyamide)
7/27/2019 Level Instrument manual
17/36
Endress + Hauser 5
E
Applications
Controlling pumps and valves with one switch or signal level height or limit
7/27/2019 Level Instrument manual
18/36
6 Endress + Hauser
E
Installation
The floating switch can be installed as follows: The floating switch can be inserted into the tank through a tapped hole G1A and screwed
to the compression gland (G1A). If it is installed from above, use the weight.
! Note! The fulcrum of the cable should always be horizontal.
The cable length between the fixture and the floating body is dependent on the cable type(see "Technical data"). When using the weight, place an extra strain relief (e.g. a knot in the cable) behind the
compression gland on the outside of the tank.
7/27/2019 Level Instrument manual
19/36
Endress + Hauser 7
E
Electrical connection
# Warning!
Note the switch type!
Inductive proximityswitch with switchingball (NAMUR)Order codes:
52010119, 5201012052010121, 7103551671035517, 71035518
Connection indicationL+ = black or brownL- = blue
(closing when floating)
Change-over contact(AC/DC)Order codes:52010122, 5201012352010124, 7103552071035521, 71035522
Cable colours:black + brown = contact open
black + blue = contact closed(contact position when floating)
7/27/2019 Level Instrument manual
20/36
8 Endress + Hauser
E
Technical data FTS20 (NAMUR)
Measuring system Comprising an FTS20 floating switch and an isolating amplifier, e.g.Endress+Hauser Nivotester FTL325N
Switching element Inductive proximity switch with switching ball, closed when floatingPower supply 8.2 V 2 V
Operating current 2.1 mA switched
Reverse polarity protection Yes
Switching angle Switching points top/bottom 12, measured to the horizontal
Ambient temperature Dependent on cable material;PVC, PUR and CSM: -20 +70 C
Ingress protection DIN EN 60529, IP68 (immension depth: 20 m / without temporal limit)
Ambient pressure 3 bar
Density of floating switch 0.8 g/cm3
Floating body material Polypropylene (PP)
Cable material PVC, CSM: standard length 5 m and 20 m, cross section 2 x 0.75 mm2PUR:standard length 5 m and 20 m, cross section 2 x 0.50 mm2
Areas of application andminimum cable length betweenfixing and floating body
PVC: 50 mm, suitable for water, dirty water, slightly aggressive mediaPUR: 100 mm, suitable for fuels, heating oils, liquids containing oilCSM: 100 mm, suitable for acids and alkalis
Ex approval TV 01 ATEX 1709
Ex ingress protection 0 II 2G EEx ia II B T5
Ex data T5 (Ta = 70 C) T4 (Ta = 70 C)Voltage Ci 16 V 16 VCurrent Ii 52 mA 72 mAPower Pi 180 mW 242 mWInductance Li 1 mH 1 mH
Capacitance Ci 153 nF 153 nF
7/27/2019 Level Instrument manual
21/36
Endress + Hauser 9
E
Technical data FTS20 (AC/DC)
Standards EN 60947-5-2, EN 50014:1997, EN 50020:1994
Measuring system Comprising an FTS20 floating switchSwitching element Microswitch with switching ball
Switching function Change-over contact
Switching voltage AC: max. 250 V; DC: max. 150 V
Switching current Max. 3 A (AC), max. 1 A (DC)
Switching angle Upper switching point: +25 6Lower switching point: +14 3, measured to the horizontal
Ambient temperature Dependent on cable material;PVC: +5 +70 C, PUR and CSM: -20 +85 C
Ingress protection DIN EN 60529, IP68 (immension depth: 20 m / without temporal limit)
Ambient pressure 3 barDensity of floating switch 0.8 g/cm3
Floating body material Polypropylene (PP)
Cable material PVC, CSM: standard length 5 m and 20 m, cross section 2 x 0.75 mm2
PUR:standard length 5 m and 20 m, cross section 2 x 0.50 mm2
Areas of application and minimumcable length between fixing andfloating body
PVC: 50 mm, suitable for water, dirty water, slightly aggressive mediaPUR: 100 mm, suitable for fuels, heating oils, liquids containing oilCSM: 100 mm, suitable for acids and alkalis
7/27/2019 Level Instrument manual
22/36
10 Endress + Hauser
E
Dimensions
FTS20 floating switch
Compression gland weight Weight
(Dimensions in mm)
135
29,2
G1A
SW 41
190
32,5
7/27/2019 Level Instrument manual
23/36
Endress + Hauser 11
E
7/27/2019 Level Instrument manual
24/36
12 Endress + Hauser
E
7/27/2019 Level Instrument manual
25/36
D
E
F
KA180F/00/fr/12.0652010984
Interrupteur flotteurFTS20
FllstandgrenzschalterLevel Limit Switch
Dtecteur de niveau
C i d it
7/27/2019 Level Instrument manual
26/36
2 Endress + Hauser
F
Consignes de scurit
L'interrupteur flotteur FTS20 doit uniquement tre mis en uvre en tant que dtecteur de niveau,dans des liquides appropris. Il peut en rsulter des dangers en cas d'utilisation inapproprie.
L'appareil doit uniquement tre mont, raccord et mis en service par un personnel qualifi etautoris, en respectant tout particulirement cette instruction abrge, les normes en vigueur, les prescriptions lgales, et
les certificats (selon la version et l'application).
Symboles de scurit
# Avertissement !Le symbole Avertissement fait allusion des actions ou processus qui, s'ils ne sont pas excutsde faon conforme, peuvent entraner des blessures sur des personnes ou porter atteinte lascurit. Observez les instructions de travail de faon prcise, et procdez avec soin.
! Remarque !
Le symbole Remarque fait allusion des processus qui, s'ils ne sont pas excuts de faonconforme, peuvent avoir une influence sur le fonctionnement ou dclencher une raction imprvisiblede l'appareil.
V i t d' il
7/27/2019 Level Instrument manual
27/36
Endress + Hauser 3
F
Variantes d'appareils
Numro de
commande
Longueur
par cble
Type de interrupteur
N
A
M
U
R
Initiateur avec bille de commutation pour une mise en uvre en zone explosive2 conducteurs selon EN 60947-5-6 (NAMUR)Utlisation avec amplificateur-sparateur ; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
avec cble en PVC - polychlorure de vinyle (pour eau, eaux uses)
5201012071035517
5 m20 m
avec cble en PUR - polyurthane (pour carburants et huiles)
5201012171035518
5 m20 m
avec cble en CSM - polythylne chlorosulfon (pour acides et bases)
A
C
/
D
C
Micro-interrupteur avec bille de commutation pour utilisation standard,3 conducteurs, inverseur pour max. 250 V c.a. / 150 V c.c.
5201012271035520
5 m20 m
avec cble en PVC polychlorure de vinyle (pour eau, eaux uses)
5201012371035521
5 m20 m
avec cble en PUR polyurthane (pour carburants et huiles)
5201012471035522
5 m20 m
avec cble en CSM polythylne chlorosulfon (pour acides et bases)
Accessoires
Nivotester FTL325N Amplificateur-sparateur
7/27/2019 Level Instrument manual
28/36
4 Endress + Hauser
F
Principe de fonctionnement
Un lment de commutation intgr dans l'interrupteur flotteur commute en cas d'cart par rapport la position horizontale.
Le processus de commutation est dclench par le mouvement d'une bille en acier et excut,suivant la version, par un initiateur inductif ou un micro-interrupteur.L'initiateur inductif met un signal de commande selon EN 60947-5-6 (NAMUR), en tant que sortietout ou rien. La version avec micro-interrupteur possde un contact inverseur.
Caractristiques Dtection sre de seuils de remplissage dans les liquides Connexions lectriques selon NAMUR pour la zone explosive (jusqu' la zone 1) ou inverseur
(AC/DC) pour une utilisation standard universelle Diffrents matriaux de cble pour diffrents fluides
Petit diamtre pour montage simple travers un trou taraud G1A
52010125 Raccord viss presse-toupe G1A, en PVC
52010126 Contre-crou G1A, en PVC
52010127 Lest (revtement en polyamide)
Applications
7/27/2019 Level Instrument manual
29/36
Endress + Hauser 5
F
Applications
Commande de pompes et vannes par interrupteur ou signalisation du niveau ou du seuil de remplissage
Montage
7/27/2019 Level Instrument manual
30/36
6 Endress + Hauser
F
Montage
L'interrupteur flotteur peut tre mont de la faon suivante : L'interrupteur flotteur peut tre insr dans un rservoir par l'extrieur, travers un trou
taraud G1A, et fix l'aide du raccord viss presse-toupe (G1A) Il convient d'utiliser le lest en cas de montage par le haut
! Remarque ! Le point d'articulation du cble doit toujours tre l'horizontale.
La longueur de cble entre la fixation et le flotteur dpend du type de cble(voir caractristiques techniques) En cas d'utilisation du lest, il convient de fixer un dispositif de dcharge supplmentaire
(p. ex. un noeud sur le cble) derrire le raccord viss presse-toupe, sur le ct extrieurdu rservoir
Raccordement lectrique
7/27/2019 Level Instrument manual
31/36
Endress + Hauser 7
F
Raccordement lectrique
# Avertissement !Veillez au type d'interrupteur !
Dtecteur inductif deproximit avec bille decommutation (NAMUR)N darticle:
52010119, 5201012052010121, 7103551671035517, 71035518
Identification de raccordementL+ = noir ou brunL- = bleu( fermeture au flottage)
Inverseur (AC/DC)N darticle:52010122, 52010123
52010124, 7103552071035521, 71035522
Couleurs des cbles :noir + brun = contact ouvert
noir + bleu = contact ferm(tat des contacts au flottage)
Caractristiques techniques FTS20 (NAMUR)
7/27/2019 Level Instrument manual
32/36
8 Endress + Hauser
F
Caractristiques techniques FTS20 (NAMUR)
Systme de mesure Compos de l'interrupteur flotteur FTS20 et d'un amplificateur-sparateur, p. ex.Endress+Hauser Nivotester FTL325N
lment de commutation Dtecteur inductif de proximit avec bille de commutation, fermeture au flottageAlimentation 8,2 V 2 V
Courant de service 2,1 mA commut
Protection contre l'inversion de polarit Oui
Angle de commutation Points de commutation en haut / en bas 12, mesur par rapport l'horizontale
Temprature ambiante Dpendante du matriau du cble ;PVC, PUR et CSM : -20 +70 C
Degr de protection DIN EN 60529, IP68 (immersion 20 m, pas de limitation de temps)
Pression ambiante 3 bars
Densit l'interrupteur flotteur 0,8 g/cm3
Matriau du flotteur Polypropylne (PP)
Matriau du cble PVC, CSM: longueur standard 5 m et 20 m, section 2 x 0,75 mm2PUR: longueur standard 5 m et 20 m, section 2 x 0,50 mm2
Domaines d'application et longueurminimale de cble entre la fixationet le flotteur
PVC : 50 mm, de prfrence pour l'eau, les eaux uses et les fluides lgrement corrosifsPUR : 100 mm, de prfrence pour les carburants, le fioul, les liquides teneur en huileCSM : 100 mm, de prfrence pour les acides et les bases
Agrment Ex TV 01 ATEX 1709
Type de protection antidflagrante 0 II 2G EEx ia II B T5Donnes Ex T5 (Ta = 70 C) T4 (Ta = 70 C)
Tension Ui 16 V 16 VCourant Ii 52 mA 72 mAPuissance Pi 180 mW 242 mWInductance Li 1 mH 1 mH
Capacit Ci 153 nF 153 nF
Normes EN 60947-5-2 EN 50014:1997 EN 50020:1994
7/27/2019 Level Instrument manual
33/36
Endress + Hauser 9
F
Caractristiques techniques FTS20 (AC/DC)
Normes EN 60947 5 2, EN 50014:1997, EN 50020:1994
Systme de mesure compos d'un interrupteur flotteur FTS20lment de commutation Micro-interrupteur avec bille de commutation
Fonction de commutation inverseur
Tension de commutation AC : max. 250 V ; DC : max. 150 V
Courant de commutation max. 3 A (AC), max. 1 A (DC)
Angle de commutation point de commutation suprieur : +25 6,point de commutation infrieur : +14 3, mesur par rapport l'horizontale
Temprature ambiante dpendante du matriau du cble ;PVC : +5 +70 C, PUR et CSM : -20 +85 C
Degr de protection DIN EN 60529, IP68 (immersion 20 m, pas de limitation de temps)
Pression ambiante
3 barsDensit l'interrupteur flotteur 0,8 g/cm3
Matriau du flotteur polypropylne (PP)
Matriau du cble PVC, CSM: longueur standard 5 m et 20 m, section 2 x 0,75 mm2
PUR: longueur standard 5 m et 20 m, section 2 x 0,50 mm2
Domaines d'application et longueur
minimale de cble entre la fixationet le flotteur
PVC : 50 mm, de prfrence pour l'eau, les eaux uses et
les fluides lgrement corrosifsPUR : 100 mm, de prfrence pour les carburants, le fioul,
les liquides teneur en huileCSM : 100 mm, de prfrence pour les acides et les bases
Dimensions
7/27/2019 Level Instrument manual
34/36
10 Endress + Hauser
F
Dimensions
Interrupteur flotteur FTS20
Raccord viss presse-toupe Lest
(Cotes en mm)
135
29,2
G1A
SW 41
190
32,5
7/27/2019 Level Instrument manual
35/36
Endress + Hauser 11
F
L'attestation d'examen CE de type figure en langue anglaise aux pages 11 et 12.
7/27/2019 Level Instrument manual
36/36
KA180F/00/a3/12.06, 52010984, CCS/FM6 12
www.endress.com/worldwide