Quality-Assurance System for Manufacturer of Materials€¦ · AD 2000-Merkblatt W0 Audit report no.: 811/Q-00 0025 Area of validity: Seamless tubes, see annex to certificate Manufacturing

TÜV Rheinland Industrie Service GmbH E-008-D-Rev22 Notifizierte Stelle für Druckgeräte, Kennnummer: 0035 Am Grauen Stein, D-51105 Köln

Certificate

Quality-Assurance System

for Manufacturer of Materials

acc. to Directive 2014/68/EU Certificate no.: 01 202 811/Q-00 0025 Name and address of the manufacturer:

Salzgitter Mannesmann Stainless Tubes Deutschland GmbH Bahnstraße 61 D - 42859 Remscheid

Herewith we certify that the material manufacturer has established and applies a Quality Management System. The system was audited according to the European Directive 2014/68/EU, Annex I, Par. 4.3, with regard to the materials as listed in the scope of approval.

Tested acc. to Directive 2014/68/EU:

QM System acc. to EN 764-5, article 4.2 and AD 2000-Merkblatt W0

Audit report no.:

811/Q-00 0025

Area of validity:

Seamless tubes, see annex to certificate

Manufacturing plant:

Salzgitter Mannesmann Stainless Tubes Deutschland GmbH Bahnstraße 61 D - 42859 Remscheid

Valid until:

January 31, 2023

Cologne, February 26, 2020 Dipl.-Ing. (FH) Roman Alexander Meyers

Annex to Certificate No. : 01 202 811/Q-00 0025

Formblatt 8 Rev. 22

Scope according to

Directive 2014/68/EU Annex I §4.3

EN 764-4 AD 2000-Merkblatt W0

FPC, Regulation (EU) No. 305/2011(System 2+)

Manufacturer Work Nationality Date Page No..

Name : Salzgitter Mannesmann Stainless Tubes Deutschland GmbH Remscheid 15.01.2020 1 TÜV Rheinland

Bahnstraße 61 Area Germany Industrie Service

Location : 42859 Remscheid Stainless steel pipe manufacturing Rev.:1 von : 12 GmbH

Cur Materials-term Materials-No.

Material Specification

Delivery Cond.

Article Type of Product

Dimensions Weight max

Technical Specifications

Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg

Technical Regulations

from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 8a 8b 9 10

1. Materials according to harmonized European standards (hEN) and European Approval for Materials (EAM) acc. Directive 2014/68/EU The use of the materials according to Directive 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the

particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

1 1.4301 (X 5 CrNi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 When using the materials 2 1.4306 (X 2 CrNi 19-11) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 after column 2 to 4 are the 3 1.4307 (X 2 CrNi 18-9) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 Definitions and limits of 4 1.4311 (X 2 CrNiN 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 Pressure Equipment Directive or 5 1.4401 (X 5 CrNiMo 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 the to observe the respective 6 1.4404 (X 2 CrNiMo 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 regulations 7 1.4424 (X 2 CrNiMoSi 18-5-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 8 1.4429 (X 2 CrNiMoN 17-13-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 9 1.4435 (X 2 CrNiMo 18-14-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5

10 1.4436 (X 5 CrNiMo 17-13-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 11 1.4462 (X 2 CrNiMoN 22-5-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 12 1.4466 (X 2 CrNiMoN 25-22) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 13 1.4501(X 2CrNiMoCuWN 25-7-4) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 14 1.4529 (X 1 NiCrMoCuN 25-20-6) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 15 1.4539 (X 1 NiCrMoCuN 25-20-5) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 16 1.4541 (X 6 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 17 1.4550 (X 6 CrNiNb 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 18 1.4558 (X 2 NiCrAlTi 32-20) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 19 1.4571 (X 6 CrNiMoTi 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5

Remarks +AT = solution annealed +NT = normalized and tempered a = PMA for the use in pressure equipment +AR = as rolled +QT = quenched and tempered in Directive 2014/68/EU neccessary +M = thermo mechanical treated +S = soft annealed +N = normalized or normalizing formed +SR = stress relieved


Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

1. Materials according to harmonized European standards (hEN) and European Approval for Materials (EAM) acc. Directive 2014/68/EU The use of the materials according to Directive 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of

the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

20 1.4580 (X 6 CrNiMoNb 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 When using the materials 21 1.4910 (X 3 CrNiMoN 17-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 after column 2 to 4 are the 22 1.4912 (X 7 CrNiNb 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 Definitions and limits of 23 1.4940 (X 7 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 Pressure Equipment Directive or 24 1.4941 (X 8 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 the to observe the respective 25 1.4948 (X 6 CrNi 18-11) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 regulations 26 1.4958 (X 5 NiCrAlTi 31-20) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 27 1.4959 (X 8 NiCrAlTi 32-21) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 28 1.4961 (X 8 CrNiNb 16-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 29 1.4981 (X 8 CrNiMoNb 16-16) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 30 1.4988 (X 8 CrNiMoVNb 16-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 EN 10216-5 31 1.0254 (P235TR1) EN 10216-1 +N Seamless pipes 4 30 80 385 EN 10216-1 32 1.0255 (P235TR2) EN 10216-1 +N Seamless pipes 4 30 80 385 EN 10216-1 33 1.0258 (P265TR1) EN 10216-1 +N Seamless pipes 4 30 80 385 EN 10216-1 34 1.0259 (P265TR2) EN 10216-1 +N Seamless pipes 4 30 80 385 EN 10216-1 35 1.0345 (P235GH) EN 10216-2 +N Seamless pipes 4 30 80 385 EN 10216-2 36 1.0425 (P265GH) EN 10216-2 +N Seamless pipes 4 30 80 385 EN 10216-2 37 1.7218 (25CrMo4) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 38 1.0488 (P275NL1) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

1. Materials according to harmonized European standards (hEN) and European Approval for Materials (EAM) acc. Directive 2014/68/EU The use of the materials according to Directive 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of

the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

39 1.1104 (P275NL2) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 When using the materials 40 1.0562 (P355N) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 after column 2 to 4 are the 41 1.0565 (P355NH) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 Definitions and limits of 42 1.0566 (P355NL1) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 Pressure Equipment Directive or 43 1.1106 (P355NL2) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 the to observe the respective 44 1.8905 (P460N) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 regulations 45 1.8935 (P460NH) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 46 1.8915 (P460NL1) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 47 1.8918 (P460NL2) EN 10216-3 +N Seamless pipes 4 30 80 385 EN 10216-3 48 1.8876 (P620Q) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 49 1.8877 (P620QH) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 50 1.8890 (P620QL) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 51 1.8879 (P690Q) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 52 1.8880 (P690QH) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 53 1.8881 (P690QL1) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 54 1.8888 (P690QL2) EN 10216-3 +QT Seamless pipes 4 30 80 385 EN 10216-3 55 1.0451 (P215NL) EN 10216-4 +N Seamless pipes 4 30 80 385 EN 10216-4 56 1.0453 (P265NL) EN 10216-4 +N Seamless pipes 4 30 80 385 EN 10216-4



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

2. Materials according to the AD 2000-Code The use of the materials according to DGR 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

57 1.4301 (X 5 CrNi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 When using the materials 58 1.4306 (X 2 CrNi 19-11) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 after column 2 to 4 are the 59 1.4307 (X 2 CrNi 18-9) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Definitions and limits of 60 1.4311 (X 2 CrNiN 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Pressure Equipment Directive or 61 1.4401 (X 5 CrNiMo 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 the to observe the respective 62 1.4404 (X 2 CrNiMo 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 regulations 63 1.4424 (X 2 CrNiMoSi 18-5-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 64 1.4429 (X 2 CrNiMoN 17-13-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 65 1.4435 (X 2 CrNiMo 18-14-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 66 1.4436 (X 5 CrNiMo 17-13-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 67 1.4462 (X 2 CrNiMoN 22-5-3) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 68 1.4466 (X 2 CrNiMoN 25-22) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 69 1.4501(X 2CrNiMoCuWN 25-7-4) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 70 1.4529 (X 1 NiCrMoCuN 25-20-6) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 71 1.4539 (X 1 NiCrMoCuN 25-20-5) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 72 1.4541 (X 6 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 73 1.4550 (X 6 CrNiNb 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 74 1.4558 (X 2 NiCrAlTi 32-20) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 75 1.4571 (X 6 CrNiMoTi 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

2. Materials according to the AD 2000-Code The use of the materials according to DGR 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the

applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

76 1.4580 (X 6 CrNiMoNb 17-12-2) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 When using the materials 77 1.4910 (X 3 CrNiMoN 17-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 after column 2 to 4 are the 78 1.4912 (X 7 CrNiNb 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Definitions and limits of 79 1.4940 (X 7 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Pressure Equipment Directive or 80 1.4941 (X 8 CrNiTi 18-10) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 the to observe the respective 81 1.4948 (X 6 CrNi 18-11) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 regulations 82 1.4958 (X 5 NiCrAlTi 31-20) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 83 1.4959 (X 8 NiCrAlTi 32-21) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 84 1.4961 (X 8 CrNiNb 16-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 85 1.4981 (X 8 CrNiMoNb 16-16) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 86 1.4988 (X 8 CrNiMoVNb 16-13) EN 10216-5 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 87 1.4577 (X 3 CrNiMoTi 25-25) SEW 400 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10



Formblatt 8 Rev. 22

Scope according to









Material Specification Delivery

Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4


88 2.4360 (NiCu 30 Fe) VdTÜV 263 +S Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 When using the materials 89 2.4816 (NiCr 15 Fe) VdTÜV 305 +S;+A Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 after column 2 to 4 are the 90 2.4068 (LC-Ni 99) VdTÜV 345 +S Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Definitions and limits of 91 2.4819 (NiMo 16 Cr 15 W) VdTÜV 400 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Pressure Equipment Directive or 92 1.4439 (X 2 CrNiMoN 17 13 5) VdTÜV 405 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 the to observe the respective 93 1.4876 (X 10 NiCrAlTi 32 20) VdTÜV 412 +S;+A Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 regulations 94 1.4466 (X 2 CrNiMoN 25 22) VdTÜV 415 / 2 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 95 1.4462 (X 2 CrNiMoN 22 5 3) VdTÜV 418 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 96 1.4539 (X 1 NiCrMoCu 25 20 5) VdTÜV 421 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 97 2.4610 (NiMo 16 Cr 16 Ti) VdTÜV 424 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 98 2.4858 (NiCr 21 Mo) VdTÜV 432 / 2 +S Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 99 1.4876 H (X 10 NiCrAlTi 32 20 H) VdTÜV 434 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 100 2.4602 (NiCr 21 Mo 14 W) VdTÜV 479 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 101 1.4563 (X 1 NiCrMoCuN 31 27 4) VdTÜV 483 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 102 2.4663 (NiCr 23 Co 12 Mo) VdTÜV 485 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 103 1.4877 (X 5 NiCrCeNb 32 27) VdTÜV 497 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 104 2.4856 (NiCr 22 Mo 9 Nb) VdTÜV 499 +S Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 105 1.4529 (X 1 NiCrMoCuN 25 20 6) VdTÜV 502 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10



Formblatt 8 Rev. 22

Scope according to









Material Specification Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

2. Materials according to the AD 2000-Code The use of the materials according to DGR 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular

material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

106 1.4410 (X 2 CrNiMoN 25-7-4) VdTÜV 508 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 When using the materials 107 1.4562 (X 1 NiCrMoCu 32 28 7) VdTÜV 509 / 2 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 after column 2 to 4 are the 108 Esshete 1250 VdTÜV 520 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Definitions and limits of 109 1.4952 (X6rNinbN25-20) VdTÜV 546 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 Pressure Equipment Directive or 110 1.4908 (X8CFrNi19-11) VdTÜV 547 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 the to observe the respective 111 1.4907 (Super 304 H) VdTÜV 550 +AT Seamless pipes 1,5 50 20 219,1 AD 2000 W2/ W10 regulations 112 1.0258 (P265TR1) DIN EN 10216-1 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 113 1.0259 (P265TR2) DIN EN 10216-1 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 114 1.0345 (P235GH) DIN EN 10216-2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 115 1.0425 (P265GH) DIN EN 10216-2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 116 1.7218 (25CrMo4) DIN EN 10216-2 +QT Seamless pipes 4 30 80 385 AD2000 W4/ W10 117 1.0488 (P275NL1) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 118 1.1104 (P275NL2) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 119 1.0562 (P355N) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 120 1.0565 (P355NH) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 121 1.0566 (P355NL1) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 122 1.1106 (P355NL2) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10



Formblatt 8 Rev. 22

Scope according to









Material Specification Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4


123 1.8905 (P460N) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 When using the materials 124 1.8935 (P460NH) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 after column 2 to 4 are the 125 1.8915 (P460NL1) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 Definitions and limits of 126 1.8918 (P460NL2) DIN EN 10216-3 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 Pressure Equipment Directive or 127 1.0451 (P215NL) DIN EN 10216-4 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 the to observe the respective 128 1.0453 (P265NL) DIN EN 10216-4 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 regulations 129 1.0488 (P275NL1) VdTÜV 352/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 130 1.1104 (P275NL2) VdTÜV 352/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 131 1.0562 (P355N) VdTÜV 354/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 132 1.0565 (P355NH) VdTÜV 354/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 133 1.0566 (P355NL1) VdTÜV 354/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 134 1.1106 (P355NL2) VdTÜV 354/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 135 1.8905 (P460N) VdTÜV 357/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 136 1.8935 (P460NH) VdTÜV 357/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 137 1.8915 (P460NL1) VdTÜV 357/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10 138 1.8918 (P460NL2) VdTÜV 357/2 +N Seamless pipes 4 30 80 385 AD2000 W4/ W10



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

3. Materials according to international standards ( e. g. ASTM, ASME, IBR etc. ) The use of the materials according to DGR 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the


139 1.0308 (E235) EN 10297-1, a +N; +QT Seamless pipes 4 30 80 385 EN 10297-1 When using the materials 140 1.0580 (E355) EN 10297-1, a +N; +QT Seamless pipes 4 30 80 385 EN 10297-1 after column 2 to 4 are the 141 1.1151 (C22E) EN 10297-1, a +N; +QT Seamless pipes 4 30 80 385 EN 10297-1 Definitions and limits of 142 1.1181 (C35E) EN 10297-1, a +N; +QT Seamless pipes 4 30 80 385 EN 10297-1 Pressure Equipment Directive or 143 1.1191 (C45E) EN 10297-1, a +QT Seamless pipes 4 30 80 385 EN 10297-1 the to observe the respective 144 1.1221 (C60E) EN 10297-1, a +QT Seamless pipes 4 30 80 385 EN 10297-1 regulations 145 1.7218 (25CrMo4) EN 10297-1, a +QT Seamless pipes 4 30 80 385 EN 10297-1 146 1.7220 (34CrMo4) EN 10297-1, a +QT Seamless pipes 4 30 80 385 EN 10297-1 147 1.7225 (42CrMo4) EN 10297-1, a +N Seamless pipes 4 30 80 385 EN 10297-1 148 1.6580 (30CrNiMo8) EN 10297-1, a +N Seamless pipes 4 30 80 385 EN 10297-1 149 1.1141 (C15E) EN 10297-1, a +N Seamless pipes 4 30 80 385 EN 10297-1 150 1.7131 (16MnCr5) EN 10297-1, a +N Seamless pipes 4 30 80 385 EN 10297-1 151 1.7139 (16MnCrS5) EN 10297-1, a +N Seamless pipes 4 30 80 385 EN 10297-1 152 1.4006 (X 12 Cr 13) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 153 1.4301 (X 5 CrNi 18-10) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 154 1.4306 (X 2 CrNi 19-11) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 155 1.4307 (X 2 CrNi 18-9) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 156 1.4311 (X 2 CrNiN 18-10) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 157 1.4401 (X 5 CrNiMo 17-12-2) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 158 1.4404 (X 2 CrNiMo 17-12-2) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 159 1.4424 (X 2 CrNiMoSi 18-5-3) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4



160 1.4429 (X 2 CrNiMoN 17-13-3) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 When using the materials 161 1.4435 (X 2 CrNiMo 18-14-3) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 after column 2 to 4 are the 162 1.4436 (X 5 CrNiMo 17-13-3) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 Definitions and limits of 163 1.4460 (X 3 CrNiMoN 27-5-2) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 Pressure Equipment Directive or 164 1.4462 (X 2 CrNiMoN 22-5-3) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 the to observe the respective 165 1.4466 (X 2 CrNiMoN 25-22) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 regulations 166 1.4501(X 2 CrNiMoCuWN25-7-4) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 167 1.4529 (X 1 NiCrMoCuN 25-20-6) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 168 1.4539 (X 1 NiCrMoCuN 25-20-5) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 169 1.4541 (X 6 CrNiTi 18-10) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 170 1.4550 (X 6 CrNiNb 18-10) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 171 1.4558 (X 2 NiCrAlTi 32) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 172 1.4571 (X 6 CrNiMoTi 17) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 173 1.4580 (X 6 CrNiMoNb 17) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 174 1.4845 (X 12 CrNi 25) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 175 1.4878 (X 12 CrNiTi 18) EN 10297-2, a +AT Seamless pipes 1,5 50 20 219,1 EN 10297-2 176 2.4066 (Ni 99,2) DIN 17740, a +SR Seamless pipes 1,5 50 20 219,1 DIN 17740 177 2.4068 (LC-Ni 99) DIN 17740, a +SR Seamless pipes 1,5 50 20 219,1 DIN 17740 178 2.4642 (NiCr 29 Fe) DIN 17740, a +G; +AT Seamless pipes 1,5 50 20 219,1 DIN 17742



Formblatt 8 Rev. 22

Scope according to










Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4



179 2.4816 (NiCr 15 Fe) DIN 17742, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17742 When using the materials 180 2.4817 (LC-NiCr 15 Fe) DIN 17742, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17742 after column 2 to 4 are the 181 2.4851 (NiCr 23 Fe) DIN 17742, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17742 Definitions and limits of 182 2.4951 (NiCr 20 Ti) DIN 17742, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17742 Pressure Equipment Directive or 183 2.4375 (NiCu 30 Al) DIN 17743, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17743 the to observe the respective 184 2.4610 (NiMo 16 Cr 16 Ti) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 regulations 185 2.4619 (NiCr 22 Mo 7 Cu) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 186 2.4650 (NiCo 20 Cr 20 MoTi) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 187 2.4660 (NiCr 20 CuMo) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 188 2.4663 (NiCr 23 Co 12 Mo) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 189 2.4858 (NiCr 21 Mo) DIN 17744, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17744 190 2.4066 (Ni 99,29) DIN 17751, a +SR Seamless pipes 1,5 50 20 219,1 DIN 17751 191 2.4068 (LC-Ni 99) DIN 17751, a +SR Seamless pipes 1,5 50 20 219,1 DIN 17751 192 2.4360 (NiCu 30 Fe) DIN 17751, a +SR Seamless pipes 1,5 50 20 219,1 DIN 17751 193 2.4610 (NiMo 16 Cr 16 Ti) DIN 17751, a + AT Seamless pipes 1,5 50 20 219,1 DIN 17751 194 2.4619 (NiCr 22 Mo 7 Cu) DIN 17751, a + AT Seamless pipes 1,5 50 20 219,1 DIN 17751 195 2.4642 (NiCr 29 Fe) DIN 17751, a + AT Seamless pipes 1,5 50 20 219,1 DIN 17751 196 2.4660 (NiCr 20 CuMo) DIN 17751, a + AT Seamless pipes 1,5 50 20 219,1 DIN 17751 197 2.4816 (NiCr 15 Fe) DIN 17751, a + AT Seamless pipes 1,5 50 20 219,1 DIN 17751



Formblatt 8 Rev. 22

Scope

according to

Directive 2014/68/EU

Annex I §4.3

EN 764-4 AD 2000-

Merkblatt W0

FPC, Regulation (EU)

No. 305/2011(System 2+)







Delivery Cond.




Remarks

Thick-ness

Requirements

mm mm 1=t / 2=kg


from

Up to

from Up to

1 2 3 4 5 6a 6b 7a 7b 1 2 3 4

3. Materials according to international standards ( e. g. ASTM, ASME, IBR etc. ) The use of the materials according to DGR 2014/68/EU is bound to the publication of Harmonized European Standards or to the qualification by a European material approval or to the particular material appraisal. With that the manufacturing reliability for equivalent material grades according to other standards (e.g. BS, AFNOR, ASME) is proved. The requirements and limits of the applicable code respectively the PED must be observed for the use of material grades listed in column 2 to 4.

198 2.4817 (LC-NiCr 15 Fe) DIN 17751, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17751 When using the materials 199 2.4851 (NiCr 23 Fe) DIN 17751, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17751 after column 2 to 4 are the 200 2.4858 (NiCr 21 Mo) DIN 17751, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17751 Definitions and limits of 201 2.4951 (NiCr 20 Ti) DIN 17751, a +AT Seamless pipes 1,5 50 20 219,1 DIN 17751 Pressure Equipment Directive or 202 1.3912 (Ni 36) SEW 385, a +AT Seamless pipes 1,5 50 20 219,1 SEW 385 the to observe the respective 203 1.3920 (Ni 46) SEW 385, a +AT Seamless pipes 1,5 50 20 219,1 SEW 385 regulations 204 1.4558 (X 2 NiCrAlTi 32-20) SEW 400, a +AT Seamless pipes 1,5 50 20 219,1 SEW 400 205 1.4562 (X 1 NiCrMoCu 32-28-7) SEW 400, a +AT Seamless pipes 1,5 50 20 219,1 SEW 400 206 1.4828 (X 15 CrNiSi 20-12) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 207 1.4841 (X 15 CrNiSi 25-20) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 208 1.4845 (X 12 CrNi 25-21) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 209 1.4864 (X 12 NiCrSi 36-16) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 210 1.4876 (X 10 NiCrAlTi 32-20) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 211 1.4878 (X 12 CrNiTi 18-9) SEW 470, a +AT Seamless pipes 1,5 50 20 219,1 SEW 470 212 1.0212 (E215) EN 10305-1, a +N Seamless pipes 4 30 80 385 EN 10305-1 213 1.0308 (E235) EN 10305-1, a +N Seamless pipes 4 30 80 385 EN 10305-1 214 1.0580 (E355) EN 10305-1, a +N Seamless pipes 4 30 80 385 EN 10305-1 215 1.0308 (E235) EN 10305-1, a +N Seamless pipes 4 30 80 385 EN 10305-1 216 1.0225 (E275) EN 10305-2, a +N Seamless pipes 4 30 80 385 EN 10305-1 217 1.0580 (E355) EN 10305-2, a +N Seamless pipes 4 30 80 385 EN 10305-1


Documents

Quality-Assurance System for Manufacturer of Materials€¦ · AD 2000-Merkblatt W0 Audit report no.: 811/Q-00 0025 Area of validity: Seamless tubes, see annex to certificate Manufacturing