8/13/2019 PL_TB450_2012_07_10 (1)
1/7
PL TB450 PRELIMINARY
Blaue Laser Diode 1.4 W in TO56 BauformBlue Laser Diode 1.4 W in TO56 Package
2012-07-10 1
Besondere Merkmale
Typ. Emissionswellenlnge 450nm Effiziente Strahlungsquelle fr Dauerstrich- und
gepulsten Betriebsmodus TO56 Gehuse Laserdiode isoliert gegen Gehuse
Anwendungen
Projektion Messtechnik Bhnenbeleuchtung
Sicherheitshinweise
Je nach Betriebsart emittieren diese Bauteilehochkonzentrierte, sichtbare Strahlung, diegefhrlich fr das menschliche Auge sein kann.Produkte, die diese Bauteile enthalten, mssengem den Sicherheitsrichtlinien der IEC-Norm60825-1 behandelt werden.
Features
Typ. emission wavelength 450nm Efficient radiation source for cw and pulsed
operation TO56 package Laser diode isolated against package
Applications
Projection Metrology Stage lighting
Safety Advice
Depending on the mode of operation, thesedevices emit highly concentrated visible lightwhich can be hazardous to the human eye.Products which incorporate these devices have tofollow the safety precautions found in IEC 60825-1Safety of laser products.
8/13/2019 PL_TB450_2012_07_10 (1)
2/7
TypType
Opt. AusgangsleistungOptical Output PowerPop(W) (Tcase 25C)
BestellnummerOrdering Code
PL TB450 1.4 Q65111A2303
GrenzwerteBetrieb auerhalb dieser Bedingungen kann das Bauteil schdigenMaximum RatingsOperation outside these conditions may damage the device
BezeichnungParameter
SymbolSymbol
Wert
Values
EinheitUnit
min. max.
Betriebsstrom (TGehuse25C)1)
1) Der Betrieb bei den Grenzwerten beeinflusst die Lebensdauer.Operation at maximum ratings may influence the life time.
2)
2) Eine maximale optische Ausgangsleistung von 1.7W darf nicht berschritten werden.A maximum optical output power of 1.7W may not be exceeded.
Operating Current (TCase25C)1)2) I
F 1.6 A
Betriebstemperatur1)2)Operating Temperature1)2)
TCase 0 + 70 C
LagertemperaturStorage Temperature
Tstg - 40 + 85 C
SperrspannungReverse Voltage
VR 5 V
Lttemperatur max. 10 sec.
Soldering Temperature max. 10 sec.
Tsolder 260 C
Sperrschichttemperatur 1)2)Junction temperature 1)2)
Tj 150 C
2012-07-10 2
PL TB450 - PRELIMINARY
8/13/2019 PL_TB450_2012_07_10 (1)
3/7
Laserkennwerte (Pop = 1.4 W, TGehuse= 25 C)Laser Characteristics (Pop = 1.4 W, Tcase= 25 C)
BezeichnungParameter
SymbolSymbol
Wert
Values
EinheitUnit
min. typ. max.
EmissionswellenlngeEmission Wavelength
peak 440 450 460 nm
Spektrale Breite (Halbwertsbreite)Spectral Width (FWHM)
4 nm
SchwellstromThreshold Current
Ith 0.2 0.3 A
Betriebsstrom
Operating CurrentIF 1.2 1.5 A
Betriebsspannung
Operating VoltageVF 6.0 V
Strahldivergenz (FWHM)
Beam Divergence (FWHM) 15 deg
Strahldivergenz (FWHM)
Beam Divergence (FWHM)
18 25 deg
Polarisation Verhltnis
Polarization RatioPR 20:1 TE:TM
Thermischer Widerstand
(pn-bergang zu Gehuse)Thermal resistance (junction to case)
Rth 18 K/W
PL TB450 - PRELIMINARY
2012-07-10 3
8/13/2019 PL_TB450_2012_07_10 (1)
4/7
PL TB450 - PRELIMINARY
2012-07-10 4
Optische AusgangsleistungOptical Output PowerPop= f(IF)
SchwellstromThreshold CurrentIth= f(TCase)
BetriebsspannungOperating VoltageVF= f(IF)
EmissionswellenlngeEmission Wavelength= f(TCase)
8/13/2019 PL_TB450_2012_07_10 (1)
5/7
PL TB450 - PRELIMINARY
2012-07-10 5
Wichtige Hinweise zum Betrieb der
Laserdiode:
a) Elektrischer Betrieb:OSRAMs Laserdioden sind mit dem Ziel hchsterLeistung und Zuverlssigkeit gefertigt. Der Betriebder Laserdiode oberhalb der im Datenblattangegebenen Maximalwerte kann jedoch dieLeistung und die Zuverlssigkeit erheblichbeeintrchtigen.Die Laserdiode ist sehr empfindlich gegenberelektrostatischen Entladungen (ESD).Entsprechende Vorsichtsmanahmen sind zutreffen.
Die Laserdiode sollte mit einer mglichstrauscharmen Stromversorgung betrieben werden.
b) Verarbeitungshinweise:Ein geeignetes Wrmemanagement istausschlaggebend fr eine lange Lebensdauer derLaserdiode. Auf Grund des Designs wird die in derDiode erzeugte Wrme haupschlich ber dieGrundplatte des Gehuses abgefhrt. Es musssichergestellt sein, dass eine ausreichend gutwrmeleitende Verbindung zwischen derDiodengrundplatte und dem Khlkrper besteht.
Important notes of operation for laser diode:
a) Electrical operation:OSRAMs laser diodes are designed for maximumperformance and reliability. Operating the laserdiode above the maximum rating even for veryshort periods of time can damage the laser diodeor reduce its lifetime. The laser diode is verysensitive to electrostatic discharge (ESD). Properprecautions must be taken.The laser diode must be operated with a suitablepower supply with minimized electrical noise.
b) Mounting instructions:In order to maintain the lifetime of the laser diodeproper heat management is essential. Due to thedesign of the laser diode heat is dissipated onlythrough the base plate of the diodes body. Aproper heat conducting interconnection betweenthe diodes base plate and the heat sink must bemaintained.
8/13/2019 PL_TB450_2012_07_10 (1)
6/7
2012-07-10 6
PL TB450 - PRELIMINARY
MazeichnungPackage Outlines
5,6-0,025
0
2 0,15
1 0,15
90
2
0,4
0,1
0,4 0,1
1
2
3
1,2
max.
3x
0,45
0,05
6,5 0,5
1,2 0,1
2,3 0,13
4,2
0,1
3,55
0,05
1,5 0,08
Emission Point
A
Polarization
TE
0.17 A
Mae in mm / Dimensions in mm
PinbelegungPin Connection
Pin 1 LD Anode
Pin 2 CasePin 3 LD Cathode
8/13/2019 PL_TB450_2012_07_10 (1)
7/7
PL TB450 - PRELIMINARY
2012-07-10 7
EU RoHS compliant product
Published byOSRAM Opto Semiconductors GmbH
Leibnizstrasse 4, D-93055 Regensburgwww.osram-os.com
All Rights Reserved.
The information describes the type of component and shall not be considered as assured characteristics.Terms of delivery and rights to change design reserved. Due to technical requirements components may containdangerous substances. For information on the types in question please contact our Sales Organization.PackingPlease use the recycling operators known to you. We can also help you get in touch with your nearest sales office. Byagreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing materialthat is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costsincurred.
Components used in life-support devices or systems must be expressly authorized for such purpose! Criticalcomponents, may only be used in life-support devices or systems with the express written approval of OSRAM OS.A critical component is a component used in a life-support device or system whose failure can reasonably be expectedto cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system.Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintainand sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered.
http://www.osram-os.com/http://www.osram-os.com/