Birkosit tds msds 2012

A.I. Schulze Chemotechnische Fabrik e.K. Alleinhersteller und Vertrieb BIRKOSIT Dichtungskitt

®

A.I. Schulze Chemotechnische Fabrik e.K., Johannes-Robert-Becher-Straße 39, 02827 GÖRLITZ - GERMANY

A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0 Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20 Company address: Account number 4 562 135 800 email: [email protected] Johannes-Robert-Becher-Straße 39 IBAN DE33 8559 1000 4562 1358 00 Web: www.a-i-schulze.com 02827 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden GERMANY VAT ref. no. DE812553785 HRA 7441

BIRKOSIT Dichtungskitt®

for maximum temperature and pressure resistance Product number AIS B010 BIRKOSIT BIRKOSIT Dichtungskitt

®

is a single-component, paste luting agent/sealing material for Description industrial use wherever conditions of temperature combined with pressure on smooth, plane sealing surfaces (butt joints) make extreme demands on the quality of the sealing compound. This applies, in particular, to the sealing of metallic joints in: steam and gas turbines, compressors, generators, expanders, pumps, flange

joints, etc. BIRKOSIT BIRKOSIT Dichtungskitt

®

withstands hot steam and air, hot and cold water, light fuel Temperature oils and lubricants, as well as crude oil and natural gas at temperatures of resistance up to 900 °C. BIRKOSIT The adhesion on sealing surfaces and butt joints is so high that a one hundred Pressure percent seal is guaranteed even for pressures up to 250 bar. resistance The pressure resistance for flanges without sealing rings is guaranteed up to 450 bar, and even up to 550 bar for screw joints. BIRKOSIT When used in accordance with instructions and with regular servicing as required for Service life steam and gas turbines as well as for the application areas stated above, we guarantee a service life for use on machined sealing surfaces (butt joints) of 10 years. BIRKOSIT BIRKOSIT Dichtungskitt

®

is suitable for sealing all surface sizes. The surface quality of Fields of the sealing surfaces complies with milled/scraped surfaces with a finishing accuracy Application of Ra = 0.8 µm to 1.2 µm. Sealing surface damage of ≤ 0.2 mm is compensated with BIRKOSIT Dichtungskitt

®

. For spot repairs on badly damaged areas of ≥ 0.2 mm to 1.0 mm, we recommend

the products FILLING basic®

, FILLING 1000®

and FILLING 2000®

. BIRKOSIT Apply the BIRKOSIT Dichtungskitt

®

to the dry sealing surfaces with a brush or putty knife. Application The layer thickness to be applied is 0.2 mm to 0.3 mm. The product can be

subjected to workloads immediately! It does not cure, will not change its

consistency even after several hours, and remains flexible and elastic.

It is therefore also suitable for butt joint machining. The colour is reddish brown. Heating the tin to room temperature or adding a tenth part of standard linseed oil varnish (AIS B020) from our product range will improve the brushability.

BIRKOSIT Packed in 1 kg tins. If stored correctly, BIRKOSIT Dichtungskitt

®

has a storage life Storage of 5 years in the tin. Its properties are stable and it is flexible in use. Close the tin properly if only a part of the contents is going to be used. Product data sheet as at 01.05.2012. Current download version at www.a-i-schulze.com.

http://www.filling-products.com/

http://www.birkosit-dichtungskitt.com/cms/wp-content/uploads/2012/06/PRODUCTDATASHEET2012_ProductBIRKOSIT_AISchulze_Customers_VEN_oDV.pdf


®




for maximum temperature and pressure resistance Product number AIS B010

In addition to the product information in our product documents, the 2012 product specification sheet and the safety data sheet as per (EU) Nr. 453/2010, we confirm the following additions for our General Agency:

Quality management To ensure the high quality of our products and services and to continually improve our organisation, we regularly perform in-house audits to make sure that our company meets the requirements of the DIN EN ISO 9001 quality standard to which our company is certified.

Service life of the product BIRKOSIT Dichtungskitt®

BIRKOSIT When used in accordance with instructions and with regular servicing as Service required for steam and gas turbines, we guarantee a service life of 10 years life for use on machined sealing surfaces (butt joints) with a finishing accuracy of Ra = 0.8 µm to 1.2 µm as well as incidences of shallow, trough-like corrosion or erosion defects at these sealing surfaces of ≤ 0.2 mm. For high-pressure turbines (H),

medium-pressure turbines (M) and low-pressure turbines (L) we guarantee that the product will withstand hot steam and hot air, hot and cold water, light fuel oils and lubricants as well as crude oil and natural gas up to 900 °C and withstand pressure up

to 250 bar. BIRKOSIT The following information on the tin label of our products ensures reliable Service life data service life monitoring: on the tin Filling date, unopened useable until, service life after opening, opened on (the last detail is to be entered by qualified staff working for the customer) BIRKOSIT Unopened tin Service life data If stored correctly, we guarantee a service life of the product in the tin of 5 years. in storage Opened tins If the tins are resealed correctly after partial use, we guarantee a service life of the

product of 3 years. BIRKOSIT After removal from the tin, we guarantee a product service life of 10 years for the Product use product in use. 1 Storage life certificate as at 01.09.2012. Current download version at www.a-i-schulze.com. Görlitz, 01.09.2012 A.I. Schulze Chemotechnische Fabrik e.K. Company Management

Dieter Bartkowiak

http://www.birkosit-dichtungskitt.com/cms/wp-content/uploads/2012/09/STORAGELIFECERTIFICATE2012_ProductBIRKOSIT_AISchulze_GA_VEN_oDV.pdf


®





Safety data sheet conforming to Regulation (EU) No 453/2010 BIRKOSIT Dichtungskitt

®

Date: 01.09.2012 Page 1 of 10 replaces all previous safety data sheets The latest version may be found on our website: www.a-i-schulze.com The information provided here is based on our knowledge and experience at the current time. The safety data sheet sets out the safety requirements relating to our product and does not constitute a warranty of any particular properties. It is the responsibility of the consignee of our product to observe the existing laws and regulations. SECTION 1: Identification of the substance / mixture and of the company / undertaking 1.1. Product identifier: Registered trade name: BIRKOSIT Dichtungskitt

®

1.2. Relevant identified uses of the substance or mixture and uses advised against Usage: Sealing of metallic joints 1.3. Details of the supplier of the safety data sheet Company: A.I. Schulze Chemotechnische Fabrik e.K. Address: Johannes-Robert-Becher-Straße 39, 02827 GÖRLITZ, GERMANY Contact: Tel. +49 3581 75005-0 Fax +49 3581 75005-20 email: [email protected] 1.4. Emergency telephone number Emergency information service: Tel. +49 3581 75005-10 (24h)

http://www.birkosit-dichtungskitt.com/

mailto:[email protected]


®





Registered trade name: BIRKOSIT Dichtungskitt®

Page 2 of 10 SECTION 2: Hazards identification 2.1. Classification of the substance or mixture Not applicable as it does not meet the criteria for classification under Directive 199/45/EC. 2.2. Label elements The use of the product poses no particular risk as long as it is used in compliance with the standard regulations for industrial hygiene, health and safety. No labelling of the product is required under EC Directives. 2.3. Other hazards The product presents no significant hazard for the environment if it is disposed of in compliance with the standard regulations for waste disposal (cf. section 13). SECTION 3: Composition / information on ingredients 3.2. Mixtures Formulation based on a modified organic resin and a paraffin-base mineral oil. The formulation contains both inorganic and organic additives. The product contains the following relevant components: CAS no. Name REACH EEC no. Index no. Symbols R phrases

8001-26-1 Linseed oil varnish - - - - -

1309-37-1 Synthetic iron oxide 01-2119457614-35-0000 - - - - 3 mg/m3


®






Page 3 of 10 SECTION 4: First aid measures 4.1. Description of first aid measures General information: Inhalation is not a primary route of exposure. The advice given there is of a general nature. In case of contact with eyes: Hold eyelid wide open and rinse the eye out thoroughly with water. Consult an eye specialist if irritation persists. In case of skin contact: Remove the product as far as possible with a clean soft cloth then wash the affected areas of the skin thoroughly with soap and water. In case of ingestion: Arrange medical treatment for the affected person if necessary. In case of inhalation: Help the affected person out into the fresh air. Consult a doctor if nausea persists. 4.2. Most important symptoms and effects, both acute and delayed No known symptoms and effects to date. 4.3. Indication of any immediate medical attention and special treatment required No known special measures to be taken other than the treatment of symptoms. SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media: CO2, powder and foam extinguishers, water spray jet. Unsuitable extinguishing media: Full water jet.


®






Page 4 of 10 5.2. Special hazards arising from the substance or mixture The product is only sold in small containers therefore no particular hazards are to be anticipated as a general rule. The product is combustible. Gases and vapours which are harmful to health and have an irritant effect are released during the incineration or thermal decomposition of the product. 5.3. Advice for firefighters This advice relates to large fires only. Keep containers cool with water spray if they have been exposed to the fire. Use self-contained breathing apparatus and put on protective clothing in the event of a fire. Collect and dispose of firefighting water as far as possible. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Pick up small undamaged containers (tins, tubes, etc.). Take measures to stop the flow from any damaged containers and put on protective equipment before cleaning up any large spillages. 6.2. Environmental precautions Take measures to prevent leakage into the drainage and water systems. 6.3. Methods and material for containment and cleaning up Clean up any spillages with a dry absorbent agent (sand, earth, universal binder, etc.) and dispose of residues as instructed in section 13. Clean the floor thoroughly. 6.4. Reference to other sections See section 13.


®




for maximum temperature and pressure resistance Product number AIS B010 Registered trade name: BIRKOSIT Dichtungskitt

®

Page 5 of 10 SECTION 7: Handling and storage 7.1. Precautions for safe handling Ensure adequate indoor ventilation at all times when using the product. Do not smoke while using the product. Precisely follow the instructions for use. 7.2. Conditions for safe storage, including any incompatibilities These measures relate to the storage of large quantities of the product. Store the product in the sealed original containers in a cool and dry place. Take appropriate measures to prevent the product from entering the drainage or water circulation systems in case of spillage. Do not store the product in the vicinity of food, beverages or feedstuff, and keep out of reach of children. Heed the storage class when storing large quantities or when storing in bulk. Storage class 11 under the classification system developed by the VCI, the German chemical industries association (1991). 7.3. Specific end uses No further recommendations. SECTION 8: Exposure controls / personal protection 8.1. Control parameters No further measures required over and above those set out in section 7. 8.2. Exposure controls Individual protection measures, such as personal protective equipment: Do not eat, drink or smoke in the workplace. Avoid repeated / sustained contact with the product. Change soiled workwear and clean thoroughly before reuse. Do not rub your eyes with dirty hands. Wash your hands after working and before going to the toilet. Respiratory protection: Not required


®





®

Page 6 of 10 Eye protection: Safety glasses with side shields (not mandatory but recommended) Hand protection: Plastic gloves (not mandatory but recommended) Personal protection: Workwear SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Form: Viscous at 20 °C Colour: Coloured Odour: Characteristic 9.2. Other information Density: (25 °C) ~ 1.1 g/cm

3

Bulk density: (20 °C) not applicable Vapour pressure: (20 °C) < 1 hPa Viscosity: (25 °C) no data Solubility in water: (20 °C) virtually insoluble Solubility in fat: Partly miscible with common organic solvents pH: Not applicable Flash point: Non-flammable Ignition temperature: Non-combustible


®





®

Page 7 of 10 Explosion hazards: None Partition coefficient n-octanol/water, log POW: Not applicable SECTION 10: Stability and reactivity 10.1. Reactivity Not relevant. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions No known reactions. 10.4. Conditions to avoid The product is stable at room temperature. 10.5. Incompatible materials Strong oxidants. 10.6. Hazardous decomposition products Carbon monoxide, carbon dioxide and inorganic oxides are formed during the combustion / thermal decomposition of the product.


®





®

Page 8 of 10 SECTION 11: Toxicological information 11.1. Information on toxicological effects The use of the product poses no significant risk as long as it is used in compliance with the standard regulations for industrial hygiene, health and safety. LD/LC50 data relevant to classification: Oral LD50 4986 mg/kg (rat) SECTION 12: Ecological information 12.1. Toxicity Do not allow product to leach into the environment. Decant and treat contaminated waste water before it is discharged into the drainage system. 12.2. Persistence and degradability Not relevant. 12.3. Bioaccumulative potential Not relevant. 12.4. Mobility in soil Not relevant. 12.5. Results of PBT and vPvB assessment Not relevant.


®





®

Page 9 of 10 12.6. Other adverse effects Water hazard class WK 1 (slightly hazardous to waters) (according to VwVwS publication dated 17.05.1999, formerly WK 0 which has now ceased to exist). SECTION 13: Disposal considerations 13.1. Waste treatment methods Make sure the containers (tins, tubes, etc.) are completely empty and recycle them in the normal way. End users can dispose of small quantities of residues in the original packaging at their local hazardous waste disposal facility (mobile hazardous waste collection service). Professional users must dispose of the product in accordance with the waste code number. Waste code number: 559 07 Lute and mastic compounds, not fully hardened SECTION 14: Transport information There are no specific precautions to be taken. 14.1. UN number

- 14.2. UN proper shipping name

- 14.3. Transport hazard classes

- 14.4. Packing group

- 14.5. Environmental hazards

-


®





®

Page 10 of 10 14.6. Special precautions for the user

- 14.7. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code

- SECTION 15: Regulatory information 15.1. Safety, health and environmental regulations / legislation specific for the substance or

mixture The product is not a hazardous substance as defined by the Ordinance on Hazardous Substances and by the relevant EC Directives (67/548/EEC and 88/379/EEC), as amended at the time of issuing the data sheet. 15.2. Chemical safety assessment Not relevant. SECTION 16: Other information Subs. 1: From safety data sheets for the individual components. Safety data sheet as at 01.09.2012.Current download version at www.a-i-schulze.com.

http://www.birkosit-dichtungskitt.com/cms/wp-content/uploads/2012/10/SAFETYDATASHEET2012_ProductBIRKOSIT_AISchulze_EU453_2010_VEN.pdf

Business

Birkosit tds msds 2012