Upload
john-arllan-diestro
View
216
Download
0
Embed Size (px)
Citation preview
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
1/13
878
Rittal Catalogue 30/System accessories
One Model No.for thebase/plinth trimat the sides.
A complete base/plinth.
One Model No.for thebase/plinthcomponentsfront and rear.
Regardless of the enclosure depth,the base/plinth components at the frontand rear, pre-configured with cornerpieces, are always the same for the
chosen width.The side trim panels are simply
selected according to the enclosuredepth and the required base/plinthconfiguration. The modular conceptproduces exceptional advantages interms of cost and function.
Assembly on the enclosure isconveniently carried out from the outside.The enclosure interior offers diverseopportunities for mounting levels for cablemanagement.
Stabilisation of bayed base/plinthwith a base/plinth trim rotatedthrough 90.
The connection between the base/plinth component and the base/plinth trim, as well as between theenclosure and the base/plinth, isconveniently carried out from theoutside. Simply snap the cover capinto position, and its ready!
3 options for base/plinthfixing From the outside, with the
cover cap removed From the inside, directly
onto a bracket on thecorner piece of the base/plinth component
From the inside, with theseparate base assemblyplate. In this case, there isno need to move theenclosure for the holes inthe base.
Ideal positioning of a cable clamprail in bayed, 200 mm high base/plinths.
Tubes, e.g. for cable diversion, aresimply attached between twobrackets or spacers (PS 4199.000),see page 984.
A mounting level in this case a Crail may also be assembled in thedepth with support brackets.
The quick-assembly block allowsparticularly versatile positioning ofC rails and cross rails.see page 984.
s
The modular base /plinth concept
s
One step ahead with detail
aus TS8, Seite 56
B A S E / P L I N T H
for TS 8
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
2/13
879
Rittal Catalogue 30/System accessories
for TS 8
B A S E / P L I N T H
Base/plinth
Thanks to the logical breakdown of theentire base/plinth into two ordering units,all dimensional variants are achieved withminimum stock levels.
Other advantages include easierassembly, versatile cable entry facilitiesand the stabilising baying connection.
Basic form Cable gland options
100 mm
Stabilisation of bayed base/plinth
200 mm
Fewer parts, more possibilities, lessprocurement costs, stockkeeping andassembly the formula for the newmodular base/plinth system.
The following table illustrates five out of awide range of possible solutions on threebayed base/plinths with 200 mm height,and also demonstrates the potential savingson trim panels compared with a complete200 mm base/plinth system with two trimpanels of 100 mm height at the side in eachcase.
Example New supply includes Functional advantage Savings potential insteadof 12 trims with 100 mm
3 packs of base/plinth components
1 pack of base/plinth trim200 mm high
Continuous cable chamber 2 trims with 200 mm
3 packs of base/plinth components
1 pack of base/plinth trim200 mm high
1 pack of base/plinth trim100 mm high
Base/plinth baying bracketsTS 8601.100, see page 881
Additional stabilisationfor transportation purposes withbase/plinth trim rotated through90.
2 trims with 200 mm2 trims with 100 mm
3 packs of base/plinth components2 packs of base/plinth trim
200 mm high
Shielding of the base/plinthsfrom one another 4 trims with 200 mm
3 packs of base/plinth components
1 pack of base/plinth trim200 mm high
1 pack of base/plinth trim100 mm high
Additional connection of thebase/plinth
2 trims with 200 mm2 trims with 100 mm
Other options:
Side cable entry by fitting a 100 mm base/plinth trim panel (top or bottom).
Cable entry from the rear by dismantling one or more trim panels of the base/plinth components.
Cable clamp rail fitted on the 100 mm high trim panel.
s
Modular base/plinth diversity
s
Function and cost benefits
aus TS8, Seite 57
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
3/13
Rittal Catalogue 30/System accessories
880
B1
B2
B3
B4
17.5
47.5
92.5
62.5
32.5
80
62.5
22
50
9.4
30
30
100
200
B3
T4
T3
T2
T1
18 x 14
15 x 10
14
T5
B5
aus TS8, Seite 58
Base/plinth componentsfront and rear for TSBase/plinth component consisting of onetrim panel and two pre-configured cornerpieces. In 200 mm high base/plinth
elements, one trim panel is in two parts forcable entry.
Supply includes:1 set =2 base/plinth components,4 cover caps,4 screws and captive nuts M12for attachment to the enclosure.
Accessories:
Base assembly plates SO 2817.000,see page 886.
For enclosurewidthmm
P. ofset
Model No. TS
100 mmhigh
200 mmhigh
400 1 8601.400 8602.400
500 1 8601.500 8602.500
600 1 8601.600 8602.600
800 1 8601.800 8602.800
1000 1 8601.000 8602.000
1200 1 8601.200 8602.200
Base/plinth trim, side for TS
For mounting between the base/plinthcomponents. With 200 mm height, two100 mm base/plinth trims may also beused. Base/plinth trim (100 mm high) maybe installed rotated through 90 in order tostabilise bayed base/plinth components.
Material:Sheet steel
Colour:RAL 7022(umbra grey)
Supply includes:1 set =2 base/plinth trim panels, includingmaterial for attaching on the base/plinth
components.
Accessories:
Assembly bolts for cable clamp railsSO 2819.000,see page 887.
Also required:
Base/plinth baying bracketsTS 8601.100, see right-hand page, whenfitted rotated through 90, to stabilisebayed base/plinth components.
Possible alternative:
Base/plinth, RAL 7035,base/plinth, vented,see page 882.
For enclosure
depthmm
P. ofset
Model No. TS
100 mmhigh
200 mmhigh
400 1 8601.040 8602.040
500 1 8601.050 8602.050
600 1 8601.060 8602.060
800 1 8601.080 8602.080
* Model No. see page 882
Base/plinth components front/rear Base/plinth trim, side
Width mm B1 B2 B3 B4 B5 Depth mm T1 T2 T3 T4 T5
400 400 335 275 215 370 400 369 334 274 244 368
500 500 435 375 315 470 500 469 434 374 344 468
600 600 535 475 415 570 600 569 534 474 444 568800 800 735 675 615 770 800 769 734 674 644 768
1000 1000 935 875 815 970 900* 869 834 774 744 868
1200 1200 1135 1075 1015 1170 1000* 969 934 874 844 968
Material Colour
Base/plinth Sheet steel RAL 7022
Trim panel Plastic RAL 9005
Description of the hole patternsB1/T1 = External dimensionB2/T2 = For screw-fastening in the
thread of the enclosure cornerpiece from below
B3/T3 = For screw-fastening with cap-tive nuts to the enclosure basefrom below or above
All holes (B2 B4 / T2 T4) may beused for screw-fastening to the base.
B A S E / P L I N T H
for TS 8
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
4/13
Rittal Catalogue 30/System accessories
881
for TS 8
B A S E / P L I N T H
Base/plinth
Connecting plinth trim for TS
For covering gaps in the case of back toback or corner enclosure suites. Simplypush in between the trim panel and thecorner piece before tightening the screws.
Material:Sheet steel
Colour:Black, RAL 7022 (umbra grey)
For base/plinthheight mm
Packsof
Model No. TS
100 2 8601.110
200 2 8601.120
Base/plinth baying bracketsfor TS
Necessary if the trim panels are fittedrotated by 90 in order to additionallystabilise enclosures that have beenbayed for transportation.
Material:Sheet steel, zinc-plated, passivated.
Supply includes:Baying brackets, screws M8 x 16 mm
Packs of
Model No. TS
20 8601.100
aus TS8, Seite 59
Transport castors
For locating into the base/plinth cornerpiece, 100 or 200 mm high, by lifting ortilting.Ground clearance: approx. 100 mm.
Max. permissible static load:100 kg per twin castor
Supply includes:1 set =4 castors,4 twin castors,
2 x with, 2 x without brake.
Colour:RAL 7022 (umbra grey)
Packs of
Model No. TS
1 set
8800.390
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
5/13
882
Rittal Catalogue 30/System accessories
Base/plinth adaptor forlevelling feet and twin castorsConnection component for attachment oflevelling feet PS 4612.000, see page 891, tothe base/plinth.
Material:Sheet steel, zinc-plated, passivated.
Packs of Model No. TS
4 8800.220
Base/plinth componentsfront and rear for TSBase/plinth component consisting of onetrim panel and two pre-configured cornerpieces.Design with solid or vented trim panel.Height: 100 mm
Material:Base/plinth = Sheet steel, spray finishedTrim panel = Plastic
Colour:RAL 7035
Supply includes:1 set =
2 base/plinth components,4 trim panels,4 screws and captive nuts M12for attachment to the enclosure.
Accessories:
Filter mat for trim panel, vented,see right-hand page.
Base assembly plate SO 2817.000,see page 886.
Base/plinth dimensions,see page 880
Forenclosurewidthmm
Packsof
Model No.TS
Trim panel,solid
Model No.DK
Trim panel,vented
600 1 set
8601.605 7825.601
800 1 set
8601.805 7825.801
B A S E / P L I N T H
for TS 8
Side base/plinth trim for TS
For mounting between the base/plinthcomponents.In order to stabilise bayed base/plinthcomponents, base/plinth trims may befitted rotated through 90.Height: 100 mm
Material:Sheet steel, spray finished
Colour:RAL 7035
Supply includes:1 set =2 base/plinth trims including parts forattaching to the base/plinth components.
Also required:
Base/plinth baying bracket TS 8601.100,see page 881, when fitted rotated through90, to stabilise bayed base/plinthcomponents.
Forenclosure width
mm
Packs
of
Model No. TS
600 1 set
8601.065
800 1 set
8601.085
900 1 set
8601.095
1000 1 set
8601.015
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
6/13
883
Rittal Catalogue 30/System accessories
for TS 8
B A S E / P L I N T H
Base/plinth
aus IT-News, Seite 32
Filter mat for base/plinthcomponent, vented
To conceal the trim in the base/plinthcomponent.The mounting frame is simply pushed into
the base/plinth trim.Filter class G3 to DIN EN 779.
Supply includes:Filter mat with mounting frame.
Spare filter mats supply includes:
Filter mats without mounting frames forbase/plinth trims up to 800 mm wide.
Forenclosure
widthmm
Forbase/plinthcomponentModel No.
Packsof
Model No.DK
600 7825.601 1 7561.500
800 7825.801 1 7581.500
Packsof
Model No.DK
Spare filter mats 5 7582.500
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
7/13
884
Rittal Catalogue 30/System accessories
2
98
98
200
9
8
1
00
32.5 32.5
100
125
100
125
62.5 62.5
8.5
14
30
18 x 14
37.5
12.5
T
22.5 52.5
25
52.5
25
37.5
12.5
30
50
B
Base/plinths for PS/ ES/PC/AP universal console
For enclosures Model No. SO
Width mm Depth mm 100 mm high 200 mm high
400 500 2873.200 2874.200
400 600 2883.200 2884.200
600 400 2804.200 2805.200600 500 2807.200 2808.200
600 600 2813.200 2814.200
600 800
2846.200 2847.200
800 400
2823.200 2824.200
800 500
2829.200 2830.200
800 600
2833.200 2834.200
800 800 2848.200 2849.200
1000 400
2909.200 2910.200
1000 500
2914.200 2915.200
1000 600
2916.200 2917.200
1200 400
2836.200 2837.200
1200 500
2839.200 2840.200
1200 600
2844.200 2845.200
1200 800
2853.200 2854.200
1600 400
2905.200 2906.200
1800 500
2903.200 2904.200
Base/plinth, complete
Consisting of:Trim panels front and rear with fitted cornerpieces and trim panels at the side.
Material:Sheet steel
Colour:RAL 7022
Base/plinths for AE/AK/AP
Accessories:
Fastening bolts for cable clamp rails,see page 887.
Base assembly plate,see page 886.
For enclosures/consolesPlinth
depth mm
Model No. SO
Width mm Depth mm100 mm
high200 mm
high
600 300 279
2816.200 2826.200
600 400 370
2911.200 2912.200
800 300 279
2818.200 2828.200
800 400 370
2901.200 2902.200
800 500 440
2841.200 2842.200
1000 300 279
2801.200 2802.200
1000 400 370
2891.200 2892.200
1200 400 370
2921.200 2922.200
1200 500 440
2851.200 2852.200
1600 400 370
2961.200 2962.200
1600 500 440
2863.200 2864.200
T = Enclosure depth 50 mmB = Enclosure width
Assembly parts including 4 screws andM12 captive nuts for mounting on theenclosure.
Supplyincludes
Height
100 mm 200 mm
Corner pieces 4 4
Trim panels,
front/rear
21 x 200 mm
2 x 100 mmTrim panels,side
2 4
aus HB 29, Seite 662
B A S E / P L I N T H
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
8/13
885
Rittal Catalogue 30/System accessories
100
98
30
14 x 14
9.4
62.5 62.5
14 x 18
100 100
32.5 32.5
B
12.5
37.5 2
5
25
50
50
25
50
T
12.5
37.5
30
14 x 14
9.4
62.5 62.5
14 x 18
100 100
32.5 32.5
B
12.5
37.5 2
5
25
50
50
25
50
T
12.5
37.5
98
2
98
200
B A S E / P L I N T H
Base/plinth
aus HB 29, Seite 663
Stainless steel base/plinth,completeConsisting of:Trim panels front and rear (for height200 mm with corner pieces and removabletrim panel on one side) and trim panels atthe side.
Material:Stainless steel 1.4301 (V2A)
Surface finish:Brushed
Base/plinth 100 mm high Base/plinth 200 mm high
T = Enclosure depth 50 mmB = Enclosure width
Transport castors
For base/plinth, complete (see oppositepage). For locating onto the base/plinthcorner piece, 100 or 200 mm high,by raising or tilting.
Ground clearance: approx. 60 mm.
Max. permissible static load:100 kg per twin castor
Supply includes:1 set =4 castors,4 twin castors,
2 x with, 2 x without brake.
Colour:RAL 7022 (umbra grey)
Packs of
Model No. PS
1 set
4570.000
* Corner pieces with removable trimpanel, for optional mounting at the frontor rear.
Assembly parts including 4 screws andM12 captive nuts for mounting on theenclosure.
Supply includes
Height100 mm 200 mm
Corner pieces 2*
Trim panels front/rear 2 2
Trim panels, side 2 4
Accessories:
Levelling feet,see page 887.
Perforated plates,see page 886.
Base/plinths for PS/ES/PC/AP universal console
For enclosures
Model No. SO
Width mm Depth mm 100 mm high 200 mm high
600 400
2865.000 2875.000
600 500
2868.000 2876.000
600 600
2855.000 2877.000
800 400
2869.000 2878.000
800 500
2866.000 2879.000
800 600
2856.000 2880.000
1000 400
2867.000 2885.000
1200 400
2870.000 2886.000
1200 500
2860.000 2887.000
1200 600
2857.000 2888.000
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
9/13
886
Rittal Catalogue 30/System accessories
Perforated plateFor cable entry in the stainless steel base/plinth, complete (see page 885), e.g. whenusing levelling feet, see opposite page.A perforated plate segment is 175 mm
wide. The system punchings willaccommodate cable ties SZ 2597.000, fortidy cable routing, see page 1010.
Material:Stainless steel 1.4301
Packs of 4
* For universal console, stainless steel.
Forenclo-sure
depthmm
Number ofperforated platesrequired for plinth
width*Model No.
SO
600
mm
800
mm
1000
mm
1200
mm400 3 4 5 6 2907.000
500 3 4 5 6 2908.000
600 3 4 5 6 2913.000
Levelling feet, 100 mm highFor mounting on TS, PS and ESenclosures, for easier floor cleaning andto compensate for floor irregularities of 15 mm.Height: 100 mm
Max. permissible static load:350 kg per foot
Supply includes/Material:
1 set =4 feet, brass, nickel-plated,4 threaded bolts, stainless steel 1.4301,4 mounting plates, stainless steel 1.4301,assembly parts for attaching to theenclosure.
Packs of
Model No. SO
1 set
2859.000
Base assembly plate
For fastening the base/plinth to the floorwithout moving the enclosure or the bayedsuite. For screws up to 12 mm .
Material:Sheet steel, zinc-plated, passivated.
German utility model no. G 93 08 162French patent no. 94 06612Dutch patent no. 193 235
Packs of
Model No. SO
10 2817.000
B A S E / P L I N T H
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
10/13
887
Rittal Catalogue 30/System accessories
B A S E / P L I N T H
Base/plinth
Fastening boltsfor cable clamp railsThese lockable fastening bolts allow cableclamp rails or commercially available Crails to be installed in 100 mm plinth trims.
Material:Hexagon section steel, 19 mm across flats,zinc-plated, passivated.
Accessories:
Cable clamp rail,see page 898.
Packs of
Model No. SO
10 2819.000
Levelling feet
For mounting underneath
Base/plinth, complete, see page 884,
Stainless steel base/plinth, complete,see page 885.
For unhindered access e.g. when cleaningthe floor, and to compensate for floorirregularities.
Maximum permissible static load:400 kg/foot
Adjustment range:M12: 55 mm 125 mmM16: 45 mm 120 mm
Material:Stainless steel 1.4301
Supply includes:1 set =4 levelling feet, 4 mounting plates,including assembly parts.
German utility model no. G 94 06 468
Thread Packs of
Model No. SO
M12 1 set
2889.000
M16 1 set
2890.000
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
11/13
888
Rittal Catalogue 30/System accessories
29
T2
T1
B2
B1
T3
19
B4
B3
14
25.5
174
26
200
aus TS8, Seite 60
Cable chamber for TSThe alternative to the base/plinth. Thecable chamber has system punchings inthe depth for PS/TS accessories.The front and rear sheet steel trim panels
are simply inserted at the bottom with aguide, and screw-fastened to the frame atthe top.If required, cable chambers may be bayedat the sides; baying is implemented in thesame way as at the base frame of theenclosure.
Material:Sheet steel
Colour:Textured RAL 7032
Supply includes:Cable chamber with screws for enclosureattachment.
For primed version, please add theextension .XX1 to the order number.
Accessories:
C rail 30/15,
see page 980.Baying system,see page 910 917.
For enclosures Model No.TSWidth mm Depth mm
400 500
8600.450
400 600
8600.460
600 500
8600.650
600 600
8600.660
800 500
8600.850
800 600
8600.860
1000 500
8600.050
1000 600
8600.060
1200 500
8600.250
1200 600
8600.260
Side panels for cable chamber
For finishing off at the side addditional tothe enclosure side panel. They arefastened by simply inserting, lifting up andscrew-fastening.
Material:Sheet steel
Colour:Textured RAL 7032
For primed version, please add theextension .XX1 to the order number.
Supply includes:
Side panels,including assembly parts.
For enclosuredepth mm
Packsof
Model No. TS
500 2 8600.010
600 2 8600.020
Enclosurewidth
400 600 800 1000 1200
B1 400 600 800 1000 1200
B2 392 592 792 992 1192
B3 275 475 675 875 1075
B4 335 535 735 935 1135
Enclosuredepth
500 600 800
T1 502 602 802
T2 444 544 744
T3 375 475 675
B A S E / P L I N T H
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
12/13
889
Rittal Catalogue 30/System accessories
B2
55
210
300
14
B3
B1
32
45
320
370
400
100
23
18
2
95
60
T1
40
60
185
100
180
75
B1
R 95
R 110
B A S E / P L I N T H
Base/plinth
Base/plinth, 300 mm high
For
compact enclosures AK
Console systems AP (not for universalconsoles)
With angle brackets for cable clamp rails.
Material:Sheet steel
Colour:RAL 7032, textured
Supply includes:Cable plinth with push-in front,including 2 cam locks.Not assembled.
Accessories:
Cable clamp rail,see page 898.
ForenclosureW x D mm
B1mm
B2mm
B3mm
Model No.SO
600 x 400 600 530 400
1656.200
800 x 400 800 730 600
1658.200
1200 x 400 1200 1130 1000
1662.200
Mobile base on castors
For PS/ES/PC (based on PS)/ AP enclo-sures, consisting ofbase, unassembled4 castors,
2 x with, 2 x without brake.
Load capacity per castor:120 kg static load
Overall load capacity:360 kg static load:
Surface finish:Powder coated in RAL 7032 (pebble grey)/RAL 7035 (light grey),Castors RAL 7033 (stone grey)/RAL 5018 (turquoise).
German registered designno. M 92 01 858German patent no. 42 00 315IR registered design no. DM/023580with validity for DE, FR, IT
Mobile base/plinth for TS 8 available onrequest.
Forenclosures
Model No. SO
Wmm
Dmm
RAL7032/7033
RAL7035/5018
600 400
2979.200
600 500
2980.200
600 600
2981.200 2981.235
600 800
2982.200 2982.235
800 400
2983.200
800 500
2984.200
T1 = Enclosure depth +150 mmB1 = Enclosure width
8/22/2019 Seite878 890 HB30englisch Accessories Bases Plinths
13/13
890
1
6
70
100
16
25 16
B C
D
A
D
62.5(475)
F
75
200
75125
662.5
62.5
Transport plinthFor transporting heavy, bayed enclosuresuites. Available in 200 mm increments from2 to 5 m. Transport plinths have 2 tubeswelded in to receive cross-bars for
transportation.Variable punchings to suit all enclosurewidths of 600 mm and above.
Surface finish:Surface treated with rust inhibiting agent,may be overpainted.
Note:Please state the required width and depthof the enclosure suite when ordering.
Version with transport tubes
Version without transport tubes
Colour P. of Model No. SO
Primed inreddish-brown
rust-inhibiting paint1 1228.010
similar to RAL 7022 1 1228.110
similar to RAL 7032 1 1228.210
similar to RAL 7035 1 1228.310
Colour P. of
Model No. SO
Primed inreddish-brown
rust-inhibiting paint1 1228.000
similar to RAL 7022 1 1228.100
similar to RAL 7032 1 1228.200
similar to RAL 7035 1 1228.300
Base/plinth for DK-EL
The base/plinth can be fitted onto all DK-ELand EL enclosures with a centre part depthof 316 mm or 416 mm. Holes must bemade for attaching to the centre part; adrilling template is supplied. These mayadditionally be fitted with castors for use asa mobile base/plinth.
Material:Sheet steel
Colour:RAL 7022
Supply includes:Base/plinth, including 4 levelling feet andassembly parts.
Base/plinth for
centre part depth
Packs
of
Model No.
DK/VR
316 mm 1 7505.300
416 mm 1 7505.400
Additional castorsfor base/plinth
4 3805.500
Enclosuredepthmm
B C
400 369 275
500 469 375
600 569 475
800 769 675
A 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 4200 4400 4600 4800 5000
D 300 300 300 300 300 600 600 600 600 600 600 1000 1000 1000 1000 1000
F 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
Optionally with transport tube,internal diameter 40 mm and wall thickness 3.25 mm
B A S E / P L I N T H