DE/EN
06/05
EzOPC 4
Handbuch
Manual
Lizenzvereinbarung/Haftungsausschluss
Die Nutzung von EzOPC ist nur lizenziert, wenn die Software mit einem
Produkt von Festo Didactic wie FluidSIM®, COSIMIR® oder EasyPorts
erfolgt. Die Nutzung von EzOPC erfolgt ohne jegliche Gewährleistung,
insbesondere nicht beim Einsatz für eine industrielle Anwendung.
Licence agreement/Exclusion of liability
The use of EzOPC is licensed only when the software is used with a
product from Festo Didactic, such as FluidSIM®, COSIMIR® or EasyPorts.
No warranty whatsoever is provided for the use of EzOPC. This exclusion
of warranty applies in particular with regard to use for an industrial
application.
Benennung: MANUAL
Bezeichnung: D:EZOPC-HB-DE/EN
Stand: 06/05
Autor: Ulrich Karras
Layout: 29.06.05, Beatrice Huber
© Festo Didactic GmbH & Co. KG, 73770 Denkendorf, Germany, 2004
Internet: www.festo.com/didactic
E-Mail: [email protected]
Weitergabe sowie Vervielfältigung dieses Dokuments, Verwertung und
Mitteilung seines Inhalts verboten, soweit nicht ausdrücklich gestattet.
Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte
vorbehalten, insbesondere das Recht, Patent-, Gebrauchsmuster- oder
Geschmacksmusteranmeldungen durchzuführen.
The copying, distribution and utilization of this document as well as the
communication of its contents to others without expressed
authorization is prohibited. Offenders will be held liable for the payment
of damages. All rights reserved, in particular the right to carry out
patent, utility model or ornamental design registration.
© Festo Didactic GmbH & Co. KG • EzOPC 3
Lizenzvereinbarung/Haftungsausschluss ________________________ 2
Wozu EzOPC?_______________________________________________ 4
Was ist OPC? _______________________________________________ 4
Voraussetzungen____________________________________________ 4
Installation_________________________________________________ 5
Warnung __________________________________________________ 5
Konfiguration_______________________________________________ 6
Beispiele _________________________________________________ 13
Licence agreement/Exclusion of liability _________________________ 2
What is the purpose of EzOPC?________________________________ 23
What is OPC? ______________________________________________ 23
Requirements _____________________________________________ 23
Installation________________________________________________ 24
Note _____________________________________________________ 24
Configuration______________________________________________ 24
Examples _________________________________________________ 32
Handbuch/Manual EzOPC
Deutsch
English
Handbuch EzOPC
4 © Festo Didactic GmbH & Co. KG • EzOPC
EzOPC ist ein OPC Server, der zwei Datenverbindungen bereitstellt:
• Zu einer „EasyPort EA Baugruppe“ von Festo Didactic
• Zu einem „STEP 7 Simulator“ von Siemens PLCSIM 5.1 oder höher.
Die Daten können von jedem OPC 2.x konformen OPC-Client
geschrieben bzw. gelesen werden.
OPC steht für open connectivity via open standards und ist eine
etablierte Standardschnittstelle in der Automatisierungstechnik. Sie
sorgt für einen effizienten Datenfluss zwischen Windows-Applikationen
und Automatisierungsgeräten.
OPC definiert Interfaces und die Interoperabilität zwischen
Anwendungen und Kommunikationssystemen verschiedener Hersteller.
Dadurch werden Aufgaben wie Visualisierung, Messdatenerfassung
oder Steuerung herstellerübergreifend ermöglicht. OPC versteht sich
somit als offener Standard und ist damit unabhängig von der konkreten
Anwendung.
Nähere Informationen finden Sie auch unter
http://www.opcfoundation.org
• Microsoft 32 Bit Betriebssystem 98, ME, NT, 2000, XP
• 128 MB Hauptspeicher
• Mindestens 300 Mhz CPU
• 1 RS232 Schnittsstelle
Wozu EzOPC?
Was ist OPC?
Hinweis
Voraussetzungen
Rechneranforderungen
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 5
Zur Kommunikation mit einer externen Hardwareeinheit: EasyPort
Anschaltung
• 1 EasyPort D16 (Bestell-Nr. 167 121) oder DA (Bestell-Nr. 193 930)
• 1 Serielles Anschlusskabel (1:1) (Bestell-Nr. 162 305)
• 1 Externe 24 Volt Spannungsquelle
Zur Kommunikation mit PLCSIM:
• 1 STEP 7 Basispaket Version 5.x
• 1 STEP 7 PLCSIM Version 5.1 oder 5.2
• Für die Installation von EzOPC benötigen Sie Administratorrechte.
• Sie können EzOPC als EzOPC._setup491.exe vom Internet unter
http://www.festo.de/didactic herunterladen.
• Zur Durchführung der Installation folgen Sie den Anweisungen.
• Das Setup installiert die EzOPC Anwendung und die notwendigen
OPC Treiberkomponenten.
Es kann vorkommen, dass die Installation der Treiberkomponenten
nicht vollständig durchgeführt wird. Sie erhalten beim Aufruf von EzOPC
eine Fehlermeldung über fehlende OPC Komponenten. Diese
Schwierigkeit können Sie wie folgt umgehen:
Sie finden im Installationsverzeichnis von EzOPC die Datei
OPC_DA20_Components.exe. Sie starten die Anwendung und danach ist
die Installation vollständig.
Installation
Warnung
Handbuch EzOPC
6 © Festo Didactic GmbH & Co. KG • EzOPC
Nach der Installation müssen Sie die Kommunikationsparameter und
die in ihrem System vorhandenen Komponenten konfigurieren. Hierzu
starten Sie im Startmenü EzOPC.
Bild 1: EzOPC Aufruf
• Sie müssen EzOPC nur zur Konfiguration der Kommunikations-
parameter und der einzelnen Komponenten Ihres Systems manuell
starten.
• Später wird beim Aufbau einer OPC Verbindung die EzOPC
Anwendung automatisch gestartet.
Wollen Sie eine Hardwarekomponenten mit dem PC verbinden, so
benötigen Sie mindestens ein EasyPort. Das Easyport wird über die
serielle Schnittstelle mit dem PC verbunden. Zur Konfiguration wählen
Sie das Menü Konfiguration � Serielle Schnittstelle.
Bild 2: Konfiguration/Serielle Schnittstelle
Konfiguration
Konfiguration
Serielle Schnittstelle
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 7
In diesem Dialog können Sie einstellen, an welche Schnittstelle der
EasyPort angeschlossen werden soll.
Die grauen Felder dienen dabei nur Ihrer Information und können
gegebenenfalls nur durch einen Supportmitarbeiter von Festo Didactic
verändert werden.
Sie haben die Möglichkeit, mit verschiedenen Server Komponenten zu
kommunizieren. Hierzu müssen Sie die Kommunikation mit diesen
Komponenten konfigurieren. Starten Sie EzOPC und wählen Sie das
Menü Konfiguration � Kommunikationseinstellungen.
Bild 3: Kommunikationseinstellung
Konfiguration EasyPort
Handbuch EzOPC
8 © Festo Didactic GmbH & Co. KG • EzOPC
In der Sektion EasyPort bestimmen Sie , welchen Typ (digital, analog)
und wie viele EasyPorts angeschlossen werden.
In der nachfolgenden Abbildung sehen sie eine Beispielkonfiguration
mit einem EasyPort.
Bild 4: Konfigurationsbeispiel
In der obersten Zeile wird die serielle Schnittstellenkonfiguration
angezeigt. Die Information offline zeigt Ihnen an, dass Sie noch keine
Verbindung zum EasyPort hergestellt haben.
Darunter werden symbolisch die konfigurierten EasyPorts grafisch
dargestellt. In dem in Bild 4 dargestellten Beispiel sind zwei EasyPorts
konfiguriert, wobei das zweite EasyPort ein analoges EasyPort mit 8
digitalen Ein- und Ausgängen darstellt. Die rot durchgestrichenen Felder
zeigen an, dass Sie noch keine Verbindung zu diesen Geräten
hergestellt haben.
Es gibt zwei weitere Komponenten, zu der eine Kommunikation via
EzOPC möglich ist, die virtuelle SPS (VirtualPLC) und die SOFT-SPS
PLCSIM von der Firma Siemens.
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 9
Der Text unterhalb der EasyPort Symbolfelder besagt, dass beide
Komponenten nicht konfiguriert sind.
Easyport darf nur installiert werden, wenn auch ein EasyPort an den PC
verbunden werden soll, andernfalls erhalten Sie einen Kommunikations-
fehler im realen Betrieb.
Zur Konfiguration wählen Sie wieder das Menü Konfiguration �
Kommunikationseinstellungen.
Bild 5: PLCSIM Konfiguration
Hinweis
Konfiguration PLCSIM
Handbuch EzOPC
10 © Festo Didactic GmbH & Co. KG • EzOPC
In der Sektion PLCSIM wählen Sie zunächst die Option installiert bei
der Komponente STEP 7 PLCSIMV5.x. Als weitere
Konfigurationsmöglichkeit können sie das Anfangsbyte und Endbyte in
der SOFT-SPS festlegen. Damit können Sie die Kommunikation auf Ihre
Bedürfnisse optimieren. Andernfalls würden stets alle Datenbytes bei
der Kommunikation übertragen werden.
Bild 6: Konfigurationsbeispiel PLCSIM
Im obigen Beispiel werden die konfigurierten Bytes von 0 – 4 grafisch
angezeigt. Diese Anzeige ist dynamisch, d.h. wenn eine Kommunikation
stattfindet, dann werden die passenden LED’s aktiviert. Somit haben Sie
auch auf dieser Ebene eine Visualisierung der Kommunikation.
Die Komponente PLCSIM darf nur aktiviert werden, wenn auch die STEP
7 Software mit PLCSIM installiert ist. Andernfalls erhalten Sie einen
Kommunikationsfehler und müssen EzOPC neu starten.
Hinweis
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 11
Die Konfiguration der virtuellen SPS ist nur notwendig, wenn Sie mit der
Soft-SPS PLCSIM Hardware ansteuern oder mit dem Softwarepaket
COSIMIR® PLC von Festo Didactic arbeiten wollen.
Bild 7: Kommunikationseinstellung VirtualPLC
Es gibt verschiedene Optionen zur Konfiguration:
• EasyPort
• PLCSIM
• Loopback
Konfiguration VirtualPLC
Handbuch EzOPC
12 © Festo Didactic GmbH & Co. KG • EzOPC
Sie wollen mit der PLCSIM z.B. eine MPS Station von Festo Didactic
ansteuern. Dann müssen Sie die Station mit EasyPort verdrahten und
EasyPort wie oben erwähnt entsprechend konfigurieren. Ebenso muss
PLCSIM konfiguriert sein. Da aber PLCSIm eine Server Komponente
darstellt , fehlt noch die aktive Client Komponente zur Steuerung der
Kommunikation. Diese Rolle übernimmt die Komponente VirtualPLC.
Wählen Sie die Option EasyPort im obigen Konfigurationsfenster, vgl.
Bild 7.
Sie wollen mit PLCSIM ein Prozessmodell in COSIMIR® PLC ansteuern.
Dann konfigurieren Sie die VirtualPLC mit der Option PLCSIM. Die
virtuelle SPS bildet das feste Ein- und Ausgangsmodell eines
Prozessmodells in COSIMIR® PLC auf ein beliebiges Ein- und
Ausgangsmodell der PLCSIM ab.
Sie wollen zwei Windowsanwendungen z.B. FluidSIM® und COSIMIR®
PLC, die jeweils über einen CPC Client kommunizieren können,
miteinander verbinden. Hierzu benötigen Sie einen Server, der die
Anforderungen der beiden Clients umsetzt. Diese Serverrolle kann
ebenfalls von der Komponente VirtualPLC übernommen werden. Wählen
Sie hierzu die Option Loopback im Konfigurationsdialogfenster, vgl.
Bild 7.
Konfiguration
VirtualPLC/EasyPort
Konfiguration
VirtualPLC/PLCSIM
Konfiguration
VirtualPLC/Loopback
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 13
Wählen Sie das Menü Konfiguration � Sprache. Hier können Sie EzOPC
auf eine andere Sprache umstellen. Gegenwärtig sind nur die Sprachen
Deutsch und Englisch verfügbar. Die gewählte Sprache wird bei
Neustart von EzOPC aktiv.
Bild 8: Sprachkonfiguration
Nachfolgend wird beispielhaft mit Hilfe des Standard OPC-Client von
der Firma FactorySoft dargestellt, wie eine OPC Verbindung aufgebaut
wird.
Je nach Integration werden dabei manche Schritte in anderen
Applikationen versteckt bzw. automatisiert.
Der Standard OPC-Client von FactorySoft wird zu Testzwecken
automatisch mit EzOPC installiert.
• Starten Sie den OPC Client
• Wählen Sie nun das Menü OPC � Connect aus
Konfiguration
Spracheinstellung
Beispiele
Standard OPC-Client
Handbuch EzOPC
14 © Festo Didactic GmbH & Co. KG • EzOPC
Bild 9: Verbindungsaufbau zum EzOPC Server
• Es werden im Abschnitt Available servers alle OPC Server
aufgeführt, die auf Ihrem System installiert sind. Der EzOPC Server
heißt FestoDidactic.EzOPC.1. Selektieren Sie diesen Server durch
Mausklick, dann erscheint der Name in dem Datenfeld Server Name.
Bild 10: Serverauswahl
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 15
• Bestätigen Sie Ihre Wahl durch Mausklick auf das OK-
Schaltelement. EzOPC wird jetzt automatisch gestartet. Nach
Verbindungsaufbau mit dem EzOPC Server ändert sich das Menü
des OPC Clients wie folgt:
Bild 11: Menü OPC Client nach Verbindungsaufbau
• Sie müssen jetzt dem Client mitteilen, welche Daten er mit dem
Server kommunizieren soll. In der OPC-Sprache heißt ein solches
Kommunikationselement ein Item. Fügen Sie jetzt ein Item mit dem
Menü OPC � Add Item hinzu.
Bild 12: Auswahl der Anzeige der Kommunikationsvariablen
Handbuch EzOPC
16 © Festo Didactic GmbH & Co. KG • EzOPC
In folgenden Beispiel wurde vom EasyPort1 der InputPort1 ausgewählt.
Bild 13: Anzeige der Kommunikationsvariablen – Items
Selektieren Sie InputPort1 und klicken Sie auf Add Item, um den
Datenwert des InputPort1 anzuzeigen. Falls Sie nur spezielle Bitwerte
vom EasyPort1 anzeigen wollen, klicken Sie im linken Fensterbereich
auf Bits und es erscheint folgende Anzeige:
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 17
Bild 14: Anzeige der Bitvariablen
Sie haben zwei allgemeine Anwendungsmöglichkeiten mit FluidSIM®
und EasyPort:
• Sie wollen einen simulierten Schaltkreis über eine externe SPS
ansteuern.
• Sie wollen mit dem Logikmodul in FluidSIM® eine reale elektrisch
pneumatische Schaltung ansteuern.
• Sie benötigen die FluidSIM® Version 3.6f oder höher.
Beispiele:
FluidSIM®/EasyPort
Handbuch EzOPC
18 © Festo Didactic GmbH & Co. KG • EzOPC
Sie verdrahten die SPS mit Easyport und verbinden das EasyPort mit
dem PC. Sie konfigurieren EzOPC mit der Komponente EasyPort und
schließen EzOPC. Sie starten FluidSIM® und öffnen den gewünschten
Schaltkreis. Aktivieren Sie in FluidSIM® die OPC Kommunikation und
verbinden Sie grafisch die Komponenten FluidSIM® IN und FluidSIM®
OUT mit den entsprechenden Ports vom EasyPort EzOPC wird dann
automatisch gestartet. Starten Sie das Programm in der SPS und die
Kommunikation erfolgt nach Start der Simulation in FluidSIM®.
Bild 15: Aktive Verbindung zum EasyPort
Load = 0 zeigt die momentane Auslastung der seriellen Schnittstelle an.
In diesem Beispiel hat sie den Wert 0, sie ist also zu 0 % ausgelastet.
Sollte dieser Wert größer 90 werden, ist eine Aktualisierung der Ein-
und Ausgänge in Echtzeit nicht mehr möglich, da die maximale
Datenmenge der seriellen Schnittstelle an diesem Punkt überschritten
wird.
Steuerung mit
externer SPS
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 19
Es genügt wieder EasyPort im EzOPC zu konfigurieren. Sie wählen ein
Logikmodul in FluidSIM® und verbinden es ähnlich wie zuvor mit den
entsprechenden Ports vom EasyPort.
Sie wollen einen Schaltkreis in FluidSIM® über die Soft-SPS PLCSIM
steuern. Konfiguration des EzOPC muss dann wie folgt aussehen:
• EasyPort nicht installiert
• PLCSIM installiert und Anfangs- bzw. Endbyte sind festgelegt
• VirtualPLC nicht installiert
Sie konfigurieren die OPC Kommunikation in FluidSIM®, starten die
Simulation und starten Ihr Programm in der PLCSIM.
Sie wollen mit der Soft-SPS PLCSIM eine MPS Station ansteuern. Sie
verdrahten die MPS Station via Syslink Kabel mit dem EasyPort und
verbinden das EasyPort mit dem PC. Konfiguration des EzOPC muss
dann wie folgt aussehen:
• EasyPort installiert
• PLCSIM installiert und Anfangs- bzw. Endbyte sind festgelegt
• VirtualPLC nicht installiert
Steuerung mit FluidSIM®
Beispiele:
FluidSIM®/PLCSIM
Beispiele:
EasyPort/PLCSIM
Handbuch EzOPC
20 © Festo Didactic GmbH & Co. KG • EzOPC
Eine Kommunikation kann noch nicht stattfinden, da PLCSIM eine
Serverkomponente ist. Hierzu starten Sie die Anwendung FdEzPlc , die
mit EzOPC ebenfalls installiert wird:
Bild 16: Konfiguration des Clients FdEzPlc
Sie legen fest, welche Bytes der PLCSIM mit den entsprechenden Ports
des EasyPort verbunden werden. Klicken Sie auf Start , um die
Kommunikation zu starten.
Handbuch EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 21
Sie wollen ein Prozessmodell in COSIMIR® PLC mit der Soft-SPS PLCSIM
steuern. Konfiguration des EzOPC muss dann wie folgt aussehen:
• EasyPort nicht installiert
• PLCSIM installiert und Anfangs- bzw. Endbyte sind festgelegt
• VirtualPLC mit PLCSIM konfiguriert
Starten Sie die Simulation des Prozessmodells und das Programm in der
PLCSIM.
Sie wollen ein Prozessmodell in COSIMIR® PLC mit dem Logikmodul in
FluidSIM® steuern. Konfiguration des EzOPC muss dann wie folgt
aussehen:
• EasyPort nicht installiert
• PLCSIM installiert und Anfangs- bzw. Endbyte sind festgelegt
• VirtualPLC mit Loopback konfiguriert
Bei der Durchführung dieser Kommunikation ist zu beachten, dass die
Ausgänge des Prozessmodells auf die Eingänge von FluidSIM®
abgebildet werden und vice versa.
Beispiele:
COSIMIR® PLC/PLCSIM
Beispiele:
COSIMIR® PLC/FluidSIM®
22 © Festo Didactic GmbH & Co. KG • EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 23
EzOPC is an OPC server which provides two data links:
• To an “EasyPort EA module Baugruppe” from Festo Didactic
• To a “STEP 7 Simulator” from Siemens PLCSIM5.1 or higher.
The data can be written and read by any OPC 2x-compliant OPC client.
OPC stands for open connectivity via open standards and is an
established standard interface in the field of automation technology. It
ensures an efficient flow of data between Windows applications and
automation devices.
OPC defines interfaces and interoperability between applications and
communication systems from different manufacturers. This enables
tasks such as visualisation, measurement data acquisition or control
functions to be carried out irrespective of the makes of equipment
involved. OPC is thus an open standard which is not tied to any specific
application.
Further information is also available at http://www.opcfoundation.org
• Microsoft 32-bit operating system 98, ME, NT, 2000, XP
• 128 MB main memory
• CPU with at least 300 MHz
• 1 RS232 interface
Manual EzOPC
What is the purpose
of EzOPC?
What is OPC?
Note
Requirements
Computer requirements
Manual EzOPC
24 © Festo Didactic GmbH & Co. KG • EzOPC
For communication with an external hardware unit: EasyPort interface
• 1 EasyPort D16 (order no. 167 121) or DA (order no. 193 930)
• 1 serial connecting cable (1:1) (order no. 162 305)
• 1 external 24 V voltage supply
For communication with PLCSIM:
• 1 STEP 7 basic package, version 5.x
• 1 STEP 7 PLCSIM version 5.1 or 5.2
• You require administrator rights in order to install EzOPC
• You can download EzOPC from the internet as EzOPC._setup491.exe
at http://www.festo.de/didactic.
• Follow the installation instructions.
• The set-up installs the EzOPC application and the necessary OPC
driver components.
It might happen that the driver components will be not completely
installed. If you start EzOPC you get the error message that some OPC
components are missing. Here is a work around:
Select the file OPC_DA20_Components.exe in the installation folder of
EzOPC. Start this application and the installation will be completed.
After installing the software, you must configure the communication
parameters and the components in your system. Begin this procedure in
the EzOPC start menu.
Figure 1: EzOPC start menu
Installation
Note
Configuration
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 25
• You only need to start EzOPC manually in order to configure the
communication parameters and the individual components of your
system.
• The EzOPC will subsequently be started automatically when an OPC
link is established.
If you wish to connect a hardware component to the PC, you will require
at least one EasyPort. The EasyPort is connected to the PC via the serial
interface. To carry out the necessary configuration, select the menu
Config � Serial interface.
Figure 2: Serial Port Settings
In this dialogue box you can define the interface to which the EasyPort
is to be connected.
The grey fields are for information purposes only, and can only be
altered by a member of Festo Didactic’s support personnel, if necessary.
Configuration
Serial interface
Manual EzOPC
26 © Festo Didactic GmbH & Co. KG • EzOPC
You can communicate with various server components. To this end, you
must configure communications with these components. Start EzOPC
and select the menu Config � Communication setup
Figure 3: Communication Setup
In the EasyPort section you define which type of EasyPort (digital,
analogue) and how many EasyPorts are to be connected.
The figure below shows an example configuration with an EasyPort.
Configuration of EasyPort
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 27
Figure 4: Example configuration
The top line shows the serial interface configuration. The status offline
indicates that you have not yet established a connection to EasyPort.
A graphic presentation of the configured EasyPorts in symbolic form
appears below this information. Two EasyPorts are configured in the
example shown in Figure 4, whereby the second EasyPort is an
analogue EasyPort with 8 digital inputs and outputs. The fields which
are crossed out in red indicate that you have not yet established a
connection to these devices.
There are two other components with which communication is possible
via EzOPC - the virtual PLC and the SOFT PLCSIM from Siemens.
The text underneath the EasyPort symbol fields denotes that neither of
the components has been configured.
EasyPort may only be installed if an EasyPort is actually to be connected
to the PC, otherwise you will receive a communication error message in
real operation.
Note
Manual EzOPC
28 © Festo Didactic GmbH & Co. KG • EzOPC
To configure this device, select the menu Config � Communication
setup once again.
Figure 5: Configuration of PLCSIM
In the PLCSIM section, first select the installed option for the
component STEP 7 PLCSIMV5.x. As a further configuration option you
can define the start byte and end byte in the SOFT PLC. In this way, you
can optimise communications according to your requirements.
Otherwise, all data bytes would be transmitted in all communications.
Configuration of PLCSIM
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 29
Figure 6: Example PLCSIM configuration
The above example shows a graphic display of the configured bytes
from 0 to 4. This display is dynamic, i.e. the appropriate LEDs are
activated when communication takes place. This provides you with a
visualisation of communications at this level, too.
The PLCSIM component may only be activated when the STEP 7
software is installed with PLCSIM. Otherwise you will receive a
communication error message and will have to restart EzOPC.
Note
Manual EzOPC
30 © Festo Didactic GmbH & Co. KG • EzOPC
The virtual PLC only requires to be configured if you wish to control
hardware via the Soft PLCSIM or work with the COSIMIR® PLC from
Festo Didactic.
Figure 7: Communication Setup for VirtualPLC
Various configuration options are available:
• EasyPort
• PLCSIM
• Loopback
Configuration of VirtualPLC
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 31
If you wish to use the PLCSIM to control an MPS station from Festo
Didactic, for example, you must wire up the station to EasyPort and
configure EasyPort accordingly as stated above. PLCSIM must also be
configured. However, as PLCSIM constitutes a server component, an
active client component is required to control communications. This
function is performed by the VirtualPLC component.
Select the EasyPort option in the above configuration window, cf.
Figure 7.
If you wish to control a process model in COSIMIR® PLC with PLCSIM,
configure the VirtualPLC via the PLCSIM option. The virtual PLC maps
the fixed input and output model of a process model in COSIMIR® PLC
onto any input and output model of the PLCSIM.
If you wish to interconnect two Windows applications such as FluidSIM®
und COSIMIR® PLC, each of which is able to communicate via a CPC
client, you will require a server to implement the requests from the two
clients. Once again, the VirtualPLC component can perform this server
function. To this end, select the Loopback option in the configuration
dialogue window, cf. Figure 7.
Configuration of
VirtualPLC/EasyPort
Configuration of
VirtualPLC/PLCSIM
Configuration of
VirtualPLC/Loopback
Manual EzOPC
32 © Festo Didactic GmbH & Co. KG • EzOPC
Select the menu Config � Language. Here you can switch EzOPC to a
different language. German and English are the only languages which
are available at present. The selected language will be active after
restarting EzOPC.
Figure 8: Language configuration
The procedure for establishing an OPC connection is presented below
by reference to the example of the standard OPC client from the
FactorySoft company.
Depending on the degree of integration, some steps may be concealed
in other applications and/or automated.
The standard OPC client from FactorySoft is installed automatically with
EzOPC for test purposes.
• Start the OPC client.
• Now select the menu OPC � Connect.
Configuration of
language setting
Examples
Standard OPC client
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 33
Figure 9: Establishing a connection with the EzOPC server
• The Available servers section lists all the OPC servers which are
installed on your system. The EzOPC server is called
FestoDidactic.EzOPC.1. After selecting this server via a mouse click,
its name will appear in the Server Name data field.
Figure 10: Server selection
Manual EzOPC
34 © Festo Didactic GmbH & Co. KG • EzOPC
• Confirm your selection by clicking on the OK button. EzOPC will now
be started automatically. After the connection to the EzOPC server
has been established, the menu of the OPC client will alter as
follows:
Figure 11: OPC client menu after establishing connection
• You now need to inform the client as to what data is to be
communicated with the server. In OPC language, such a
communication element is referred to as an item. Now add an item
via the menu OPC � Add Item.
Figure 12: Options for the display of communication variables
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 35
In the following example, InputPort 1 of EasyPort1 has been selected.
Figure 13: Display of communication variables – Item
Select InputPort1 and click on Add Item to display the data value of
InputPort1. If you wish to display only specific bit values of EasyPort1,
click on Bits in the left area of the window, whereupon the following
display will appear:
Manual EzOPC
36 © Festo Didactic GmbH & Co. KG • EzOPC
Figure 14: Display of bit variables
Two general applications are available with FluidSIM® and EasyPort:
• You wish to control a simulated circuit via an external PLC.
• You wish to control a real electrical pneumatic circuit with the
FluidSIM® logic module.
• You require FluidSIM® version 3.6f or higher.
Examples:
FluidSIM®/EasyPort
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 37
Wire the PLC up to the EasyPort and connect the EasyPort to the PC.
Configure EzOPC with the EasyPort component and close EzOPC. Start
FluidSIM® and open the desired circuit. Activate OPC communications in
FluidSIM® and, in graphic mode, connect the components FluidSIM® IN
and FluidSIM® OUT to the corresponding ports of EasyPort. EzOPC will
then be started automatically. Start the programme in the PLC and
communications will be effected after starting the simulation in
FluidSIM®.
Figure 15: Active connection to EasyPort
Load = 0 indicates the current workload of the serial interface. In this
example the value is 0, indicating a capacity utilisation of 0 %. Should
this value exceed 90, it will no longer be possible to update the inputs
and outputs in real time, as the maximum data volume for the serial
interface is exceeded at this point.
Control with
external PLC
Manual EzOPC
38 © Festo Didactic GmbH & Co. KG • EzOPC
It is sufficient to configure EasyPort in EzOPC once again. Select a logic
module in FluidSIM® and connect it to the corresponding ports of
EasyPort according to the same procedure as described above.
If you wish to control a circuit in FluidSIM® via the Soft PLCSIM, the
configuration of the EzOPC must be as follows:
• EasyPort not installed
• PLCSIM installed and start and end byte defined
• VirtualPLC not installed
Configure OPC communications in FluidSIM®, start the simulation and
start your programme in the PLCSIM.
To control an MPS system with the Soft PLCSIM, wire the MPS station
up to the EasyPort via Syslink cable and connect the EasyPort to the PC.
The EzOPC configuration must then be as follows:
• EasyPort installed
• PLCSIM installed and start and end byte defined
• VirtualPLC not installed
Control with FluidSIM®
Examples:
FluidSIM®/PLCSIM
Examples:
EasyPort/PLCSIM
Manual EzOPC
© Festo Didactic GmbH & Co. KG • EzOPC 39
No communication can take place yet, as PLCSIM is a server component.
To enable communications, start the FdEzPlc application, which is also
installed with EzOPC:
Figure 16: Configuration of the FdEzPlc client
Define which bytes of the PLCSIM are to be connected to the
corresponding ports of the EasyPort. Click on start to initiate
communications.
Manual EzOPC
40 © Festo Didactic GmbH & Co. KG • EzOPC
If you wish to control a process model in COSIMIR® PLC via the Soft
PLCSIM, the EzOPC configuration must be as follows:
• EasyPort not installed
• PLCSIM installed and start and end byte defined
• VirtualPLC configured with PLCSIM
Start the simulation of the process model and the programme in
PLCSIM.
If you wish to control a process model in COSIMIR® PLC via the logic
module in FluidSIM® , the EzOPC configuration must be as follows:
• EasyPort not installed
• PLCSIM installed and start and end byte defined
• VirtualPLC configured with Loopback
When implementing this communication mode, it is to be ensured that
the outputs of the process model are mapped onto the inputs of
FluidSIM® and vice-versa.
Examples:
COSIMIR® PLC/PLCSIM
Examples:
COSIMIR® PLC/FluidSIM®
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 350 /GrayImageDepth -1 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /Unknown
/Description >>> setdistillerparams> setpagedevice