1
ã , 2004
Copyright Kohler China Ltd., 2004
368 201419
C
A. Summary Of Key Requirements
Observe all local plumbing codes.
Install the unit to a level subfloor.
Provide properly-dimensioned framing.
!
!
!
! Baths are designed for a variety of installations,
depending upon the model chosen.
A.
!
!
!
!
B. Product Inspection
Uncrate and inspect bath for damage. Leave all
materials in carton during construction to prevent
damage.
B.
1036301-T01-B
BEFORE YOU BEGINBEFORE YOU BEGIN
ACRYLIC BATH
INSTALLATION INSTRUCTIONS
K-18775T/K-18776T
DUO
·
·
·
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-please leave these
instructions for the consumer.
IMPORTANT: All installations must comply with council
and local authority by-laws. It is the responsibility of the
installer to ensure that the waste is made watertight by
means of silicone sealant or caulking compound.
·
·
·
·
·
·
·
PRODUCT REQUIREMENTSPRODUCT REQUIREMENTS
ROUGHING-IN
A. :A.Ordering Information:
B.Product Information:
B. :
2
Fixture*
Bathing well
Bathing well
To overflow
To overflow
* Approximate measurements
Basin area
450 1030mm
450 1178mm
653 1422mm
653 1570mm
Water depth
Water depth
306mm
306mm
Top area
Capacity
Capacity
171L
188L
Weight
24kg
27kg
1525
Duo
1675
Duo
*
450 1030mm
450 1178mm
653 1422mm
653 1570mm
*
306mm
306mm
171L
188L
24kg
24kg
1525
1675
``
UNIT: mmmm
Roughing-in: :
1670
430
4694
395
285
380
760
5250
1525
430
4694
400
285
381
76252
50
K-18775T K-18776T
1036301-T01-B
: 52
Diameter of overflow hole: 52
: 52
Diameter of overflow hole: 52
/
17295T-CP
Accessories/Hardware:
Drain 17295T-CP
: 50
Diameter of drain hole: 50
: 50
Diameter of drain hole: 50
Optional
A. Old Bath Removal
Disconnect the drain at the trap. Remove the old wallmaterial. Slip boards under the old bath feet to protectthe floor, and slide the old bath out of the recess asillustrated.
A.
Old Bath Floor Protection Board
SITE REQUIREMENTS
B.B. Subfloor Preparation
Check the flooring under the bath, and make repairs as
needed. Make sure the subfloor is level.
C.C. Bath Area Construction preparation
Possible framing arrangements are illustrated below.
Use the framing construction appropriate for your
particular bath model. Some modifications may be
needed for other types of construction, if preferred.
3
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
B. Materials RequiredA. Tools Required B.A.
·
·
·
·
·
·
·
·
Adjustable pipe
wrench
Rule
Level
Safety shoes
Safety glasses
Square
Pliers
Utility knife
·
·
·
·
·
·
·
Plumbers putty
Wall coverings, as necessary
Silicone sealant
Gypsum ciment (optional)
Construction adhesive
(optional)
Protective covering for
bathtub
Nails
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
( )
( )
( )
C. Clearance Requirements
Check the rough-in and room dimensions to provide
adequate available space for the bath unit.
C.
1036301-T01-B
2). Recess InstallationThe suggested framing construction is illustrated.
2).
Finished Wall
Wall
FramingConstruction 1/16" (2mm) Gap Between
Bath Rim and Framing
2
Bath Rim
Recommended For Drop-in Models
1). Corner InstallationThe suggested framing construction is illustrated.
1).
Finished Wall
Wall
1/16" (2mm) Gap BetweenBath Rim and Framing
2
Bath Rim
41036301-T01-B
FramingConstruction
3). Peninsular InstallationThe suggested framing construction is illustrated.
3).
Finished Wall
Wall
FramingConstruction
1/16" (2mm) Gap BetweenBath Rim and Framing
2
Bath Rim
BEFORE INSTALLING UNITBEFORE INSTALLING UNIT
D.D. Plumbing Preparation
Position the plumbing according to rough-in dimensions.
Cap the supplies and check for leaks.
4).
4). Sunken Installation
Refer to rough-in notes on page 1 for cut-out details.
Do not hang the bath by the rim.
1/16" (2mm) Gap BetweenBath Rim and Framing
2
Bath Rim
5
A. Your new whirlpool has been manufactured to thehighest possible standards. However please inspect forany possible damage that may have occurred in transit.
: Warranty does not cover damage to bathcaused in transit or installation.NOTE
A.
B. The protective film original covering your whirlpool
has been removed to fit it's equipment, therefore,
carefully protect its surface during installation.
Position a protective covering or similar material in the
bottom of the unit. Be careful not scratch the bath
surface.
B.
C.C. Partially Install Bath Drain
Install the drain on the bath according to the drain
manufacturer's instructions.
1036301-T01-B
6
INSTALL BATH
A. Locate the bath in the proposedposition.IMPORTANT:
NOTICE: Do not hang the bath by the rim.
The bath must be installed level on alltop edges. The rim and the base of the bath must befully supported. Floor should be flat, level and free ofany bumps or protrusions.Remove protective film around the waste and along thetiling bead prior to installation in order to make awatertight seal at these points possible.
Apply a generous amount of fine construction mortar, orsimilar material, to the support feet and any shims used.Set the bath into the installation. Make sure the unit islevel, and is resting on all support feet. Insert the draintailpiece into the trap.
A.
1/16" (2mm) Gap BetweenBath Rim and Framing
2
Bath Rim
B. Base SupportMethod 1Floor should be flat, level and free of any bumps andprotrusions. Ensure support feet are fully supported.Bricks can be placed under the support feet to allowaccess to waste fitting if necessary.
1
Method 2Install the bath in a bed of weak mortar slurry mix (6:1)ensuring the base is fully supported.If the installation is with above floor plumbing, ensurethat free access to pipes and waste fitting is provided.
2(6:1)
B.
Rim MUST Be Supported Brick Support Wall
Suport Feet MUST Be Supported Bricks allow accessto waste fitting
Slurry Base
Rim MUST Be SupportedBrick Support Wall
1036301-T01-B
71036301-T01-B
C. Bath Rim Support
Drop-In Models:Risk of product damage. Do not support the
weight of the bath by the rim.After the bath is securely positioned and bath rim wellsupported, please complete step 7). Install theplumbing and thoroughly check the unit for leaks. Whenyou are satisfied with the result, proceed with step (1)and step (2) below.
(1). Install the ceramic or marble tiles. Seal the jointsbetween the bath rim and the finished tiled wall usingsilicone sealant. RTV (Room Temperature Vulcanizing)sealant is recommended.(2). For sunken type installation, construct the ceramicor marble tiles. Seal the joints between the bath rimand the tiled wall with silicone sealant.
CAUTION:
A.
B.
C.
D.
CAUTION:
NOTE: An access panel will simplify future
maintenance.
Risk of damage to bath bottom and subfloor,
Ensure a watertight seal on the bath drain connections.
A. When the bath is securely positioned, connect the
drain to the trap.
B. Install the faucet valving and spout tee. When drilling
bathtub for faucet, ensure sufficient clearance to avoid
brick support wall. Open the hot and cold water valves
and check the supply connections for leaks.
C. Run water into the bath and check the drain
connections for leaks.
D. Fill the bathtub up to the overflow level and check
overflow unit for leaks.
Paste Mortar
Tile
Ng SiliconeSealant
Tiling Bead
Brick
Rebated Into Wall
Ng SiliconeSealant
50 25mmTimberBatten
Paste Mortar
Tile
Packed Out From Wall
Paste Mortar
Tile
Brick
Under Flange Tiling
Ng SiliconeSealant
Tile
Paste Mortar
Brick
Hob Mount Tiling Flush Front Tiling
Brick
Paste Mortar
Tile
C.
7). :
(1) (2)
(1). ( )
(2).
INSTALL PLUMBING
DIRLLING AND CUTTING ACRYLIC
DRILLING:
NOTE:
CUTTING:
Small holes can be drilled with a twist drill,
but the cutting edge MUST be backed off with an oil
stone (the sharp edge dulled). Large holes must be
drilled with a hole saw. Maximum drill size-12mm. Drill
speeds-6mm x 1800 RPM-12 mm x 900 RPM.
Always drill from acrylic surface.
If for any reason the acrylic requires cutting,
use a fine tooth hacksaw and proceed with caution.
Edges can be smoothed with a second-cut file and
medium-fine sandpaper. If the surface of the acrylic
should happen to be damaged, it can be restored by
polishing with an abrasive cleaner . Deep scratches
can be removed by rubbing with 600 grade wet & dry
sandpaper then polishing.
12mm 6mmx180 / 12mmx900
600
/
CLEAN-UP AFTER INSTALLATION
When cleaning up after installation, do not use abrasive
cleansers as they may scratch and dull the surface.
Use warm water and liquid, non-abrasive detergent to
clean the surface.
Stubborn stains, paint, or tar can be removed with
mineral spirits. Do not use cleaners containing solvent.
Plaster can be removed by scraping with wood edge.
Do not use metal scrapers, wire brushes, or other metal
tools. One of the powder type detergents may be used
on a damp cloth to provide mild abrasive action to the
residual plaster.
8
IMPORTANT CONSUMER INFORMATION
A.
2
Mequiars 28 ( )
( )
A. Consumer Responsibilities
Cleaning Acrylic Surfaces: Do not use abrasive
cleansers on any acrylic surfaces, as they will scratch
and dull the surface. Wipe out the bath after each use
to prevent a build-up of soap and scum.
If the acrylic surface becomes dull, an automotive type
rubbing compound may be used on the unit, followed
by an application of paste wax.
We recommended:
Rubbing compound mequiars mirror glaze 28 metal
polish (import product) or "green oil".
1036301-T01-B
LIMITED ONE-YEAR WARRANTYLIMITED ONE-YEAR WARRANTY
()
( )
13819
200021
Plumbing Fixtures and Fittings LimitedOne-year Warranty
Kohler plumbing fixtures and fittings are warranted tobe free of manufacturing defects.
This product is warranted for one year from date ofpurchase. Kohler China will be responsible for anyproblems caused by manufacturing defects providedwith the invoice. Kohler China will, at its election, repair,replace or make appropriate adjustment where KohlerChina inspection discloses any such defects occurringin normal usage within one year after purchase.
Implied warranties including that of merchantability andfitness for a particular purpose are expressly limited induration to the duration of this warranty, Kohler Chinadisclaims any liability for special, incidental orconsequential damages. Damages to the productcaused by misuse, abuse and installation that is not inaccordance with the owner's manual are not coveredby this warranty.
To obtain quick warranty service, please contact yourdealer, or write to Kohler China. (Original sales receiptmust be provided as the proof of purchase.)
Kohler China Investment Company Ltd.Central Customer Service Center19/F, Shanghai Square, 138 Huai HaiRoad, Luwan District, Shanghai, PRCZip Code: 200021
This is our exclusive written warranty.
1036301-T01-B9