View
0
Download
0
Category
Preview:
Citation preview
TA-4J S.A.49 4581/48 scale detail set for HASEGAWA kit • sada detailù pro model 1/48 HASEGAWA
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
1/7 49 458
REFERENCES:Aeroguide #14
FOR BOTH SEATS
E36( V28 ) E35
( V27 )E41
( V31 )
E41( V31 )
E34 V18
E33
V19
10
26
32
1718
6
34
11
2521
7
33
12
31
14 24
36 3598
2019
film
In detail & scale #32 FOR BOTH SEATS
FOR BOTH SEATS
FE 458 + 49 458 TA-4J
2/7 49 458
pedals
pedals
V32V32
D15
43
43
42
42
80
37
E10( V38 )
27
D216
5
15
13
V35
16
3
4
13
V12
78
90
V13
109
V2995
V29( V26 )
86
86
D15( V32 )
D15
1
2
V29
V32
V26
1 2
3/7 49 458
B11 B10
47 46
46 47
96 94
9694
93 92
9392
C1 C2
66 65
V33
film
29V33
70
44
23 22
23 22
84
V1, V5, V8
V4, V6, V7
wire
38
87 88
0,8mm
44
4/7 49 458
B554
54
74
A2
A1
F5
85
69
E43
V10
91
40
82
E29
E30
5253
67 68
E2 E3
79
45
B2 B1
51 50
50 51
49 48
83
C5
E30
111 68
5/7 49 458
A13 E24
W9
41
110
C3 C4
106105
108 103
107 104
115 116
76 77
B2
A9
A10
112 113
56 57
101 102
99 100
W9
55
97 98
7171
75
72 73
B2 B1
© EDUARD M.A. 2010 Made in Czech Republicwww.eduard.com
6/7 49 458
F1
E9F16
F11
F11
F15
62
63
64
117
89
V36
V37
V9
39
V17
28
V17
28
V1728
28 V17
58 59
60 61 81
114
W1
E23
V22
30
fill fill
F1117
F1117
For futher detail sets look for 48 631 TA-4J Airbrakes and 48 644 A-4 ladder
(not included in this set)
eduard
30
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
7/7 49 458
Recommended