Portfolio Enertex KNX - Enertex Bayern GmbH€¦ · · 2018-04-23Portfolio Enertex KNX ... 0 Fax: +49 9191 73395 -29 St.-Nr. 216/125/50473 USt-ID DE 216 837 306 ... Enertex® KNX

Dokumentennummer: 50384

Bearbeiter: S. Meier

Enertex® Bayern GmbH

Innovative Systemlösungen der Energie- und Elektrotechnik

Portfolio Enertex KNXInhaltsverzeichnis

1 Control / visualization.......................................................................................................................2

1.1 Enertex® EibPC.........................................................................................................................2

1.1.1 Tender text..........................................................................................................................2

1.1.2 Image..................................................................................................................................3

1.2 Enertex® ENA – electronic net defense....................................................................................3

1.2.1 Tender text .........................................................................................................................3

1.2.2 Image..................................................................................................................................4

2 system actuators.................................................................................................................................4

2.1 Enertex® KNXnet/IP Router.....................................................................................................4

2.1.1 Tender text..........................................................................................................................4

2.1.2 Image..................................................................................................................................4

2.2 Enertex® KNXnet/IP Interface..................................................................................................5

2.2.1 Tender text..........................................................................................................................5

2.2.2 Image..................................................................................................................................6

2.3 Enertex® KNX 4Kanal LED Dimmsequencer 5A...................................................................6

2.3.1 Tender text .........................................................................................................................6

2.3.2 Image..................................................................................................................................7

2.4 Enertex® PowerSupply 960......................................................................................................8

2.4.1 Tender text .........................................................................................................................8

2.4.2 Image..................................................................................................................................9

3 measuring instruments.......................................................................................................................9

3.1 Enertex® SmartMeter................................................................................................................9

3.1.1 Tender text - Enertex® KNX Smartmeter 85A..................................................................9

3.1.2 Tender text - Enertex® KNX Smartmeter 85A RT..........................................................10

Enertex® Bayern GmbH Ebermannstädter Str. 8 91301 Forchheim www.enertex.de

ISO 9001:2008 zertifiziert [email protected] Tel: +49 9191 73395 - 0Fax: +49 9191 73395 -29

St.-Nr. 216/125/50473USt-ID DE 216 837 306GF: Dr.-Ing. Michael Schuster Registergericht Bamberg HRB 4569

Volksbank Forchheim eGDE91 7639 1000 0007 2004 80Sparkasse ForchheimDE15 7635 1040 0020 0973 17

mailto:[email protected]


Seite 2 von 22

3.2 Tender text - Enertex® KNX Smartmeter 630A (with RT)...................................................11

4 Taster..............................................................................................................................................12

4.1 Enertex® ProxyTouch KNX..................................................................................................12

4.1.1 Tender text .....................................................................................................................12

4.1.2 Image..............................................................................................................................13

5 Room controller.............................................................................................................................13

5.1 Enertex® SynOhr MultiSense KNX......................................................................................13

5.1.1 Tender Text ....................................................................................................................13

5.1.2 Image..............................................................................................................................15

5.2 Meta Raumcontroller KNX....................................................................................................16

5.2.1 Tender Text.....................................................................................................................16

5.2.2 Image..............................................................................................................................17

6 frame..............................................................................................................................................18

6.1 Enertex® AluRa.....................................................................................................................18

6.1.1 Tender Text.....................................................................................................................18

6.1.2 Image..............................................................................................................................19

7 Price list.........................................................................................................................................21

1 Control / visualization

1.1 Enertex® EibPC

1.1.1 Tender text

The EibPC is a programmable controller for the EIB/KNX system. It is characterized by ease of

use, flexible customisation, DIN rail mounting (6 units) and very low power consumption (1.2 W).

In addition, this device can be integrated into an individual LAN-based automation environment.

Its web server provides a simple, user-definable visualisation.

Commisioning is accomplished over LAN by means of the included software Enertex® EibStudio,

running on a Microsoft® Windows® or a Linux® PC. Afterwards, the LAN connection is not re-

quired for operating the Enertex® EibPC with a major part of its functionality, as it is basically

an independent controller. Only web server, control of multimedia devices (UDP telegrams), time

synchronisation over the internet and e-mail notification need a LAN connection.

Via an FT1.2 RS232-EIB/KNX interface or EIBnet/IP Interface (both not included), the Enertex®

EibPC accesses the EIB/KNX system and records the telegrams.

"Made in Germany"



St.-Nr. 216/125/50473Ust-IdNr. DE216837306GF: Dr.-Ing. Michael Schuster Registergericht Bamberg HRB 4569




Seite 3 von 22

1.1.2 Image

Figure 1: Enertex® EibPC

1.2 Enertex® ENA – electronic net defense

1.2.1 Tender text

The Enertex ENA allows a secure access to your home network from the internet. Therefore it pro-

vides following functions:

With dynamic DNS (DDNS) the home network can be accessed without the IP address must be

known. Instead the access is made by a host name, e.g. „fifth-avenue-12.no-ip.com“. Four DDNS

host names can be managed.

By means of four so-called HTTPS reverse proxies, secure connections from the internet to web

servers on the home network can be established. In this case, the reverse proxy encrypts the

connection to the respective server (e.g. the web interface of a camera) and at the same time it pro-

vides a password protection.

Via the provided OpenVPN, a secure connection can be established to all devices on your home

network. To authenticate the user a password encrypted PKCS#12 file is used. The required

OpenVPN client is available for all major operating systems. Via KNX group addresses the

connection state of individual users can be announced and / or the OpenVPN server can be com-

pletely activated / deactivated. For devices with Apple iOS the OpenVPN client automatically can







Seite 4 von 22

be started ("on demand"), if you want to access the home network.

1.2.2 Image

Figure 2: Enertex® ENA – electronic net defense

2 system actuators

2.1 Enertex® KNXnet/IP Router

2.1.1 Tender text

The KNXnet/IP Router (3U) supports up to five KNXnet/IP tunnels and can be used as line or area

coupler.

It's integrated display shows the most important configuration parameters at any time: IP address,

KNX address and number of opened tunnels.

This allows putting the device into operation very fast and trouble free.

The IP address of the fast ethernet connection can be set manually by ETS or automatically by

DHCP or Zeroconf. Furthermore the KNXnet/IP Router has a battery buffered real time clock and

offers a SNTP server.

Statistics can be viewed and settings can be changed by the integrated Telnet server.

The KNXnet/IP Router is fed by Power over Ethernet or an external 16-24V AC or 20-30V DC

power supply.

2.1.2 Image







Seite 5 von 22

Figure 3: Enertex® KNXnet/IP Router

2.2 Enertex® KNXnet/IP Interface

2.2.1 Tender text

The KNXnet/IP Interface (3U) supports up to four KNXnet/IP tunnels.

The IP address of the fast ethernet connection can be set manually by ETS or automatically by

DHCP or Zeroconf.

The KNXnet/IP Router is fed by Power over Ethernet or an external 16-24V AC or 20-30V DC

power supply. Statistics can be viewed by the integrated Telnet server.







Seite 6 von 22

2.2.2 Image

Figure 4: Enertex® KNXnet/IP Interface

2.3 Enertex® KNX 4Kanal LED Dimmsequencer 5A

2.3.1 Tender text

The Enertex® KNX 4 channel LED dim sequencer 5A is a pulse wide modeling dimmer for 12..24

V LED modules. There is the option for ceiling mounting (DK) with furniture marking or as REG

device (REG 4TE). The dimmer can dim 5A LED power per channel, that is, a maximum in the

sum of 480W of power. The independent channels can be configured in the application in any com-

bination of cold white / warm white independent channels, color channels.

Five sequences, i.e. processes of color controls in the range of seconds to hours with gentle color

changes, can be either defined by the user or be covered with 16 predefined color sequences.

The control of the colors may optionally be carried out via the primary colors red, green and blue -

in RGB (W) color mode - or via hue, saturation and brightness (HSV color mode).

Light scenes are provided for 8 and 1-bit group addresses.

The device has a power relay with which a suitable LED voltage supply can be connected on the







Seite 7 von 22

network side. Thus, the LED power supply, if necessary, is switched on or off by the actuator, so as

to minimize the standby losses of the power supply. The switching off can be time-locked by a pa-

rametrization of two timers.

Via communication objects under voltage, over current and over temperature can be detected. In

these cases the protection function trips the connected LED modules automatically until the fault

condition is removed. Thereafter, the dimmer restarts. In addition, the Enertex® KNX 4 channel

LED dim sequencer 5A has an integrated reverse polarity protection, so that during commissioning

possible damages by reverse polarity of the input are excluded.

2.3.2 Image

Figure 5: Enertex® KNX 4Kanal LED Dimmsequenzer 5A – DK-Version







Seite 8 von 22

Figure 6: Enertex® KNX 4Kanal LED Dimmsequenzer 5A – REG-Version

2.4 Enertex® PowerSupply 960

2.4.1 Tender text

The central KNX power supply unit KNXPowerSupply960 (6MW) with integrated choke supplies

the EIB/KNX bus with a stabilized DC voltage of 30 V DC, providing a current

of 960 mA. The voltage input 85-265 VAC (50/60 Hz) allows operation, independent of

the local mains voltage.

In addition, the integrated display shows actual and maximum values for voltage, current and

power. These measurements can be sent to the EIB/KNX bus via group objects.

The product comes with an USB Safe, which represents a repository for customer-specific project

data on an including USB Stick.







Seite 9 von 22

2.4.2 Image

Figure 7: Enertex® PowerSupply 960

3 measuring instruments

3.1 Enertex® SmartMeter

3.1.1 Tender text - Enertex® KNX Smartmeter 85A

The KNX Smartmeter (4U) is a 4 quadrant meter for balancing measurement of active and reactive

energy or power, respectively. Further it features an analysis of net quality and supervision of tran-

sients. Measurements can be performed in a 3-phase system or in three independent 1-phase sys-

tems with the accuracy class 1 (1%).

All measured values (current, voltage, active power, reactive power, active energy, reactive energy,

power factor, THD, harmonics, unbalanced load, zero system current) are indicated at the KNX-

Bus.

Measurement of current is performed losslessly via current transformers. Three current transfor-







Seite 10 von 22

mers, which are calibrated and delivered with the smartmeter, are qualified for direct installation at

the power supply feed-in. Currents can be measured from 2mA to 85A per phase, voltages from 0

to 265VAC. Measurement range for active power is from 0.5W to 19550W or 58650W for 3-phase

systems, respectively. Energy values are stored on a SD-card for power consumption analysis.

ETS application features beside special functions for load dependent load control, optimizing the

self energy consumption with solar collectors, calculation of electricity costs with tariff changeo-

ver, prevention of overloads several functions for supervision. These functions trigger events like a

lack of phase voltage, high net distortion, high consumption of reactive energy, high unbalanced

load or high zero system current at the bus, when given limits are exceeded. For investigation of

net quality the spectrum is analyzed up to the 50th harmonic for current and voltage. Severals su-

pervision functions provide an analysis of power supply loss, failures and damages of electrical

consumers caused by the power supply with a precise point of time.

The smartmeter is supplied only by KNX-Bus.

3.1.2 Tender text - Enertex® KNX Smartmeter 85A RT

The KNX Smartmeter (4 units at din rail) is a bidirectional meter for measuring the active and re-

active power or energy, as well for power quality analysis. The measurement will be done in three-

phase system or in three separate single-phase systems with the accuracy of class 1 (1%).

In the accuracy class 1 according to EN 62053-11 only accuracy requirements for the measuring

range between 2% and 100% of rated current are determined. For smaller currents no requirements

are defined, as these can not be accurately detected with conventional current transformers. In con-

trast, the Enertex KNX Smartmeter uses special high precision current sensors (Rogowski coils),

which are calibrated to the device in factory. Thus, very small currents to 0.002% (= 2mA) of rated

current are accurately measurable. In addition, the current is measured with very little loss (< 2mW

loss). The provided current sensors are suitable for through-hole mounting and may be installed di-

rectly at the main supply point of the grid.

The Smartmeter is powered exclusively via the bus. Therefore, the device can even be operated if

there is no voltage at the voltage inputs or the voltage has been separated.

The measuring range of the active power extends from 0.5W to 19.550W or 58.650W (three-pha-

se). Energy values or measuring values for monitoring the power quality can be recorded for analy-

sis on a SD card.


power factor, THD-U, THD-I, power harmonics, unbalanced load, zero current, power frequency)

are shown on the KNX bus.

Besides specialized functions for performance-based load control, optimization of the own energy







Seite 11 von 22

demand with photovoltaic facilities, calculating the usage or feeding charge with tariff switching

the ETS application also provides various monitoring functions. In case of exceed of limits these

functions report events as power outages, high voltage spikes, high power distortion, high reactive

energy, highly non-uniform loading of the three phases (unbalanced load) or high neutral loading

on the bus. To assess the power quality harmonics up to the 50th harmonic of current and voltage

are measured. The numerous monitoring features enable fast accurate analysis of network-related

failures, malfunctions and damages of electrical equipment.

The KNX Smartmeter 85A RT can also be operated without KNX bus. Therefore a 24VDC

power supply must be connected to the KNX terminal. In this mode all measurement data without

the harmonics are recorded every minute on the SD card. Recording moment for each measure-

ment is then selected due to an internal battery-buffered clock that (UTC/GMT+ 1 hour) is set to

the local time of Berlin at the factory and deviates one minute at maximum per year from the time

of day. If required the clock can be adjusted using the SD card.

3.2 Tender text - Enertex® KNX Smartmeter 630A (with RT)

The KNX Smartmeter (4U) is a bidirectional meter for measurement of active and reactive energy

or power, respectively. Further it features an analysis of power supply quality. Measurements can

be performed in a 3-phase system or in three independent 1-phase systems with the accuracy class

1 (1%).


power factor, THD-U, THD-I harmonics, unbalanced load, zero system current) are indicated at the

KNX-Bus.

Measurement of current is performed losslessly via extern current sensors, which can be opened

for simply installing. Three current sensors, which are calibrated and delivered with the smartme-

ter, are qualified for direct installation at the power supply feed-in. Currents can be measured from

10mA to 630A per phase, voltages from 0 to 460VAC. Measurement range for 3-phase active

power is from 7.5W to 293kW. All energy and measurement values are further stored as text data

on a SD-card for further data analysis.

ETS application features beside special functions for load dependent load control, optimizing the

self energy consumption with solar collectors, calculation of electricity costs with tariff changeo-

ver, prevention of overloads several functions for supervision. These functions trigger events like a

lack of phase voltage, high harmonic distortion, high consumption of reactive energy, high unba-

lanced load or high zero system current at the bus, when given limits are exceeded. For investigati-

on of power supply quality the spectrum is analyzed up to the 50th harmonic for current and volta -

ge. Severals supervision functions provide an analysis of power supply loss, failures and damages







Seite 12 von 22

of electrical consumers caused by the power supply with a precise point of time.

The smartmeter is supplied only by KNX-Bus.

The KNX Smartmeter 630A can also be operated without KNX busImage

Figure 8: Enertex® SmartMeter

4 Taster

4.1 Enertex® ProxyTouch KNX

4.1.1 Tender text

The ProxyTouch KNX is a capacitive touch sensor, which can be plugged behind surfaces as cera-

mics, wood and glass. It has three sensor panels in a plastic housing with a size of 210x140x12mm

and is impermeable to splash-water. The sensors can be addressed together, individually or by wi-

ping gesture. All sensor panels can also be addressed by double-click. If you touch a tile e.g., with

a plugged device at the back, on the wished sensor panel (A, B or C) a message is written to the

bus. Optionally by touching the sensor an acoustic feedback can be output which has a different

tone pitch according to the used sensor panel (A=high, B=medium, C=deep). If the device is in

programming mode a red LED is visible and a dialing tone is audible. In the cleaning process a







Seite 13 von 22

tone can be activated optionally, which notify the lock function of the button.

The reach of operation through the surface material, behind which the device is plugged is farest

25mm by using ceramics or glass and 20mm by using wood. The sensors are robust against splash-

water on the surface material.

The ProxyTouch KNX is Bus-powered only.

4.1.2 Image

Figure 9: Enertex® ProxyTouch KNX

5 Room controller

5.1 Enertex® SynOhr MultiSense KNX

5.1.1 Tender Text

"SynOhr ® multi-sense" is the world's first room controller with built in voice recognition. The

room controller measures the temperature, humidity and color intensity. A dot-matrix can show

KNX-compliant 14-byte strings. An integrated speaker outputs audio signals stored on the inclu-

ded SD card.

The vocabulary speech recognition is approximately 250 words, need not to be taught separately

and can be parameterized via the ETS, so that commands as "COMPUTER, LIGHT 30 PER-

CENT" are possible.

SynOhr ® multi-sense is fed directly from KNX bus.







Seite 14 von 22

SynOhr® MultiSense KNX is available in the following variants:

Starter Standard Premium

Room controller Heating and Cooling yes yes yes

Measurement of temperature and humidity yes yes yes

Measurement of the light color and the light incidence yes yes yes

Two touch buttons and a push button yes yes yes

14-byte KNX text message (dot matrix) yes yes yes

Speech recognition with 40 commands 6 12 40

Freely definable colors of the lightened Ring - yes yes

Play WAV files from SD card - yes yes

Monitoring of noise levels, for example, for use as a "baby monitor" - - yes

Display of 28 characters with auto-scrolling on the dot matrix - - yes

Use of the dot matrix on the display of icons (in Q3/2014) - - yes

Speech recognition wildcard commands:

A command "DIMMER _percent" can fully control a KNX dimmer

Play WAV files from SD card

- - yes

Freely definable colors of the lightened Ring - - yes

Master / slave mode, if multiple switching points in larger rooms available

(Enertex® EibPC required)- - yes

The variants are software options that are enabled on the serial number of the device and must be

licensed for the device.







Seite 15 von 22

5.1.2 Image

Figure 10: Enertex® SynOhr MultiSense KNX - silver anodized version

Figure 11: Enertex® SynOhr MultiSense KNX - black anodized version







Seite 16 von 22

Figure 12: Enertex® SynOhr MultiSense KNX - white (RAL9010) powder-coated version

5.2 Meta Raumcontroller KNX

5.2.1 Tender Text

META room controller KNX is a touch sensor with mechanical switches. The labels display the

action to be performed. Each rocker switch has two mechanical switches for actuation, (left, for

example, ON / OFF right VALUE DEFAULT). It can be configured for individual keys or as an

operating rocker of a functional group (for example, dimming) at the two corners. Each rocker can

be four times in different menus/levels. The labeling can be differently parametrized in each level.

The labels can be dynamically changed for each level. This can be achieved by group addresses via

the KNX bus, for example, to switch the display language.

When used as a single rocker feedback on group address is displayed. On the left and right of the

screen there is a status display for 1-bit objects. The display brightness can be controlled through

the built-RGBW light sensor.

The device is supplied via the bus coupler, there is no additional supply needed. There is needed

an empty socket for mounting required (all variants). An external switch allows the coupling of a

conventional switch to the KNX bus.

META room controller KNX is available in three versions

Starter Standard Premium

Roomcontroller Heating and Coolung - yes yes

Measurement Temperature and humidity - yes yes







Seite 17 von 22

Measurement of light intensity and light color yes yes yes

Rocker/Switch, one Menuswitch 2/4 2/4 4/8

Number of rockers/switches 8/16 8/16 16/32

Display-Label for each rocker yes yes yes

LCD Display with symbols and dotmatrix for roomcontroller etc. - - yes

Auto scroll with max. 28 character at dotmatrix - - yes

Dotmatrix with graphical support - - yes

External switch yes yes yes

Bus powered yes yes yes

Length/Width (mm) 90/90 90/90 180/90

Height (mm) 8,6 8,6 8,6

Enertex® MeTa® KNX is supplied in three color options - brushed aluminum, black anodized

aluminum and glossy white powder-coated (RAL9010).

5.2.2 Image

Figure 13: Enertex® MeTa® KNX PREMIUM (starting from left):

Brushed aluminum, black anodized aluminum and glossy white powder-coated (RAL9010).







Seite 18 von 22

Abbildung 14: Enertex® MeTa® KNX STANDARD/STARTER (v.l.):

Brushed aluminum, black anodized aluminum and glossy white powder-coated (RAL9010).

6 frame

6.1 Enertex® AluRa

6.1.1 Tender Text

The high quality, completely milled from one body, frame Enertex® Alura fits 55er inserts of Jung

(AS 500) and 55mm inserts from Gira (System 55).

It also fits excellently to both the room controller Meta® and SynOhr® Multisense KNX.

The Enertex® Alura is supplied in three color options - brushed aluminum, black anodized

aluminum and glossy white powder-coated (RAL9010).

In addition, these variants are available in sizes Enertex® Alura 1-times, 2-times Enertex® Alura,

Enertex® Alura available 3-times

• Fits 55er inserts from Jung Serie AS

• Fits 55er inserts from Gira Standard 55

• Fits 55er inserts from Hager Zentraleinsätze WY







Seite 19 von 22

6.1.2 Image

Figure 15: Enertex® AluRa 1-times, black anodized aluminum (right) with white insert JUNG (AS 500)

Figure 16: Enertex® AluRa 1-times,brushed aluminum with black insert JUNG (AS 500)







Seite 20 von 22

Figure 17: Enertex® AluRa 1-times,brushed aluminum, black anodized and glossy white powder-coated (RAL9010)









Seite 21 von 22

7 Price list

Valid from October 2017

Category Product Artikle No. Price

Control / vi-

sualization

Enertex® EibPC ohne Option NP 1137-02 418,49 €

Enertex® EibPC inkl. Option NP 1137-01 586,55 €

Enertex® EibPC Option NP 1137-03 223,53 €

Enertex® ENA 1156 544,54 €

system actua-

tors

Enertex® KNXnet/IP Router 1147 307,56 €

Enertex® KNXnet/IP Interface 1150 166,39 €

Enertex® KNX 4Kanal LED Dimmsequenzer 5A REG 1160-REG 179,83 €

Enertex® KNX 4Kanal LED Dimmsequenzer 5A DK 1160-DK 184,03 €

Enertex® KNX PowerSupply 960² 1152 247,06 €

measuring in-

struments

Enertex® KNX SmartMeter 85A 1149-85 342,86 €

Enertex® KNX SmartMeter 85A RT 1149-85-RT 368,07 €

Enertex® KNX SmartMeter 630A (RT) 1149-630 536,13 €

Taster

Enertex® ProxyTouch KNX 1155 238,66 €

Room control-

ler

SynOhr Enertex® Synohr MultiSense KNX Starter, Alu gebürstet 1144-03 -al 418,49 €

Aufpreis: schwarz eloxiert 1144-03 -sw 50,00 €

Aufpreis: weiß (RAL9010) pulverbeschichtet 1144-03 -ws 50,00 €

Enertex® Synohr MultiSense KNX Standard, Alu gebürstet 1144-02 -al 544,54 €

Aufpreis: schwarz eloxiert 1144-02 -sw 50,00 €

Aufpreis: weiß (RAL9010) pulverbeschichtet 1144-02 -ws 50,00 €

Enertex® Synohr MultiSense KNX Premium, Alu gebürstet 1144-01 -al 611,76 €

schwarz eloxiert 1144-01 -sw

weiß (RAL9010) pulverbeschichtet 1144-01 -ws

Enertex® Synohr MultiSense KNX – Update Starter-Stan-

dard

-

Enertex® Synohr MultiSense KNX – Update Starter-Premi-

um

- 208,40 €

Enertex® Synohr MultiSense KNX – Update Standard –

Premium

- 107,56 €







Seite 22 von 22

Category Product Artikle No. Price

MeTa KNX MeTa® KNX Premium, Alu gebürstet 1157-01-al 477,31 €

MeTa® KNX Premium, schwarz eloxiert 1157-01-sw 477,31 €

MeTa® KNX Premium, weiß (RAL9010) pulverbeschichtet 1157-01-ws 477,31 €

MeTa® KNX Standard, Alu gebürstet 1157-02-al 309,24 €

MeTa® KNX Standard, schwarz eloxiert 1157-02-sw 309,24 €

MeTa® KNX Standard, weiß (RAL9010) pulverbeschichtet 1157-02-ws 309,24 €

MeTa® KNX Starter, Alu gebürstet 1157-03-al 275,63 €

MeTa® KNX Starter, schwarz eloxiert 1157-03-sw 275,63 €

MeTa® KNX Starter, weiß (RAL9010) pulverbeschichtet 1157-03-ws 275,63 €

frames f. 55

Enertex® AluRa – einfach, Alu gebürstet 1162-1-al 29,41 €

Enertex® AluRa – einfach, schwarz eloxiert 1162-1-sw 31,09 €

Enertex® AluRa – einfach, weiß (RAL9010) pulverbeschich-

tet

1162-1-ws 32,77 €

Enertex® AluRa – zweifach, Alu gebürstet 1162-2-al 36,13 €

Enertex® AluRa – zweifach, schwarz eloxiert 1162-2-sw 37,82 €

Enertex® AluRa – zweifach, weiß (RAL9010) pulverbe-

schichtet

1162-2-ws 40,34 €

Enertex® AluRa – dreifach, Alu gebürstet 1162-3-al 52,10 €

Enertex® AluRa – dreifach, schwarz eloxiert 1162-3-sw 54,62 €

Enertex® AluRa – dreifach, weiß (RAL9010) pulverbeschich-

tet

1162-3-ws 57,14 €

All prices without VAT without shipping







Documents

Portfolio Enertex KNX - Enertex Bayern GmbH€¦ · · 2018-04-23Portfolio Enertex KNX ... 0 Fax: +49 9191 73395 -29 St.-Nr. 216/125/50473 USt-ID DE 216 837 306 ... Enertex® KNX