uSer manual - Climatronics · User manual Air humidifier and cleaner AIR-C60 — version 2015

Excellent Business Conditions.

merlin-technology.com

MERLIN® Technology GmbH

Hannesgrub Süd 10 4911 Tumeltsham / Ried i.I.

AUSTRIA

Tel +43 (0) 7752 71966Fax +43 (0) 7752 71988

[email protected]

Weitere Normen:

ÖNORM H 6020-1:2007 „Lüftungstechnische Anlagen in

Krankenanstalten – Projektierung, Errichtung und Kontrolle“

ISO 13485:2012 „Medizinprodukte – Qualitätsmanagement-

systeme – Anforderungen für Regulative Zwecke“

Superior Service & Qualität

uSer manual

Version 12/2015

aIr HumIDIFIer anD CleaneraIr-C60

2 User manual Air humidifier and cleaner AIR-C60 — version 2015 ©

™

Triple Action HumidifierModel: AW600

•Read and follow all safety rules and instructions before operating this equipment.•Please keep this manual for future reference.

Thank you for purchasing this WINIX product

3Excellent Business Conditions.User manual Air humidifier and cleaner AIR-C60 — version 2015 ©


1

Winix HumidiPür™ Triple Action Humidifier simultaneously humidifies and cleans the air. Featuring a 12 liter per day humidification capacity and 3-Stage air purification with PlasmaWave® Technology.

HumidiPür™ Model: AW600

Triple Action Humidifier with

PlasmaWave® technology removes air pollutants resulting in cleaner fresher air.

Auto ModeWINIX’s sensor detecs room humidity level to control fan speed and optimize the humidity level.

TimerThe automatic Timer indicator is used to maintain efficiency throughout the lifetime of the product.

Sleep ModeLight sensor detects when the room is dark and adjusts the unit to Sleep Mode to reduce power consumption.

® Mist HumidifierHumidiPür™ generates very fine and light mist to enhance consistent humidity level.

CleanCel® Anti-Bacterial CoatingHumidiPür™ has been treated with CleanCel® antibacterial coating to prevent growth of bacteria in the water tank and cleaning discs.

Auto Shut-OffAutomatically shuts off when the water bucket is Low.


2

Table of ContentsSafety Instructions

Product Information

Installation

Operation

Troubleshooting

Warning

Unit DiagramControl Panel/Display

Selecting a LocationSet-Up Instructions

Modes of OperationsCare and Maintenance

FAQ/SolutionsProduct Specifications

3

1112

1314

15

19

2527


3

Safety Instructions

Warning

Warning

Notice

PROHIBITED

DO NOT DISASSEMBLE

MUST FOLLOW

Ground connection protectingfrom electrical shock

Failure to follow the safety instructions can lead to personal injury or property damage.

Follow these instructions to avoid anyrisk of personal injury, property damage, electrical shocks or fire hazard.

DON’T unplug the unit by pulling on it’s power cord.

DON’T touch the plug with wet hands.

DON’T bend or place heavy object on the power cord.

DON’T replace or modify power cord.If the power cord/plug is damaged, it must be replaced by the manufacturer or a qualified technician.


4

Warning

DON’T plug multiple power plugs into an outlet. Plug directly into the wall.

DO connect the power cord to only proper power outlet with a ground connection.

DO unplug the HumidiPür™ when not in use to save on energy consumption.

DON’T plug power cord into loose or damaged electrical outlet. (This can lead to overheating or electrical shock)

DON’T attempt to repair, alter or dissasemble the unit.

DON’T operate the unit if standing water is present.


Safety Instructions

Note

5

DON’T operate HumidiPür™on an uneven surface.

DON’T place the HumidiPür™ nearflammable material (such as gas,aerosols, or benzene).

Attempt to change the bucket andrefill with clean water every day.

DON’T spray liquids directly intoair washer.

DON’T place the unit on anunstable place such as a tableor a sink.

DON’T pour water into the top of the air unit, place in water tank as directed.

Note


6

Note

DO unplug the unit and contactyour service dealer if the unitcomes in contact with water.

DON’T insert ANYTHING into theair inlet or outlet.

DON’T remove the water tank ifa child is nearby.

DON’T install the unit in the place fullof high humidity or dust.

DO unplug the unit and contact yourservice dealer if it is sunken underwater.

DON’T place anything around the unitto allow children to play or sit on.


Safety Instructions

7

DON’T disconnect thepower cord duringoperation.

DO unplug the applianceduring filling and cleaning.

DO use the HumidiPür™after assembling theAntimicrobial Disk.

DON’T insert anything intothe air inlet or outlet.

DON’T place hands or any body parts near the air outlet during operation.

DON’T place the unitnear curtains or other materials that can block the vents of the unit.

DO unplug the unit andcontact your servicedealer if any irregularnoise or smoke occurs.

DON’T place the unitnear a heat source.

DON’T strike or dropthe unit.

7

Note


8

Note

DON’T allow children toplay on or near the unit.

DON’T use hot water inthe water tank.

DON’T spray flammable liquids or gases into the unit.

DON’T lift the unit by the top.

DON’T install the unit under direct light.

DON’T place clothes and towels on top of air washer while operating.

DO clean Antibacterial disk regularly with warm tap water and allow to air dry.

DON’T use flammablematerial (such as benzeneor alcohol) to clean theunit.

DON’T spray liquids directlyinto HumidiPür™ during cleaning.


9

Safety Instructions

DON’T install the unitnear the wall or window.

DON’T put the unit nearburning cigarette orincense.

DON’T operate the unitwhile insecticide is used.

DON’T allow water tostay in the water tank fora long time while not inuse.

DON’T install the unitwhose airflow outlet is facing the wall.

DON’T drink the waterleft in the water tank orgive it to plants or animals.

After cleaning, allowAntibacterial Discs,water tank, and pre-filterto air dry completely.

DON’T operate theunit while water tankis damaged.

DON’T put the unit neara microwave oven orTV.

Note


10

DON’T overfill the watertank.

DON’T put the unit near ceilings, walls, furniture, or electronic appliances.

DO dispose of the waterto prevent it from freezingin cold weather.

DON’T lift the unit with water still in the water tank.

DO unplug the unit andmove its water tank when water is removed.

DO clean the air washerregulary, with a microfibertowel or any other cleanwiping material.

DON’T plug in if thepower plug is touchedwith water.

DON’T put magnet ormetal material on thetop of the unit.

DO use clean tap waterwithout detergent, soap,chemical compounds orhot water (over 104ºF).

Note


11

Product Diagram

Front Panel

Anti-bacterial Disc (CleanCel®)

Anti-bacterial Disc HandleWater Level IndicatorAnti-bacterial Water Tank (CleanCel®)

Water Tank Release Lever

Control Panel Display

Air Outlet CoverAir Outlet

Fan (inside)Air Outlet Release Button

HEPA + Carbon Comination Filter

Air Intake

Power Plug


12

Control Panel

Function Button1. Continuous Mode Unit operates continuously on the fan speed selected by user (Low/Mid/High) regardless of ambient humidity.2. Sleep Mode Dims control panel lights and sets the unit to operate at lowest fan speed.3. Auto-Mode Unit runs until ideal humidity level is reached and shuts off intermittently to save energy (Green “Comfort Zone”).

Power

TimerIndicator

TimerSetting Button

Low Water Indicator

ModeIndicator

PlasmaWave®

(ON/OFF Indicator)

Control Panel Lock IndicatorHigh

Humidity Indicator

LowHumidity Indicator

Fan Speed Indicator

Fan Speed Button(Low, Medium, High)

PlasmaWave®

(ON/OFF Indicator)PlasmaWave®

(ON/OFF Button)

Humidity Level IndicatorDisplays humidity level, when desirable level of humidity levels are reached they will be displayed in the green “Comfort Zone”

Orange -> Low Humidity (Below 30% RH)Blue -> High Humidity (61-70% RH)Green -> Ideal Humidity (40-60% RH)


13

4 inches

15 inches

Installation

Selecting a Location

15 inches

4 inches

Do not install the unit under direct sunlight.- Long Exposure to direct sunlight can cause defects.

HumidiPür™ must be installed and operated on an even surface.- Vibrations and noise can occur on soft or non-flat surfaces.

Product must be Installed approximately 10cm/ 4 inches away from the walland 30-40cm/ 15 inches from other electronic appliances.

Before operating the HumidiPür™, remove any plastic bags and polyfoams fromoutside and inside the unit.


14

Operation

Set-Up Instructions

1. Slide water tank out, by using the release lever located below the water tank on the front of the unit.

2. Fill the water tank with cool tap water up to the indicator line on the inside of water tank.

3. Replace the water tank by sliding it back into the unit until you hear it click into place.

4. Gently slide down the front panel and make sure that it is seated properly and lines up correctly.

Make sure to unplug the power cord before filling the unit with water.

We recommend using filtered water to prolong the life of the product.

Use cautions when moving the unit filled with water.


15

Operation

Before Turning On

1

2

3

Plug the power cord into a power outlet.

Push the POWER button.

The unit will start on AUTOMODE and the PlasmaWave® function will be ON.

A soft buzzing or clicking sound may occur during operation;if this is uncomfortable, you can turn off the PlasmaWave®

feature by using the PlasmaWave® ON/OFF button.


16

Auto Mode

Continuous Mode

1

1

Push FUNCTION button to selectAuto Mode

AIR FLOW:When ambient humidity is sensed at lessthat 60%, the unit will operate at “High”fan speed. When the ambient humidityis sensed at greater than 60% the unitwill operate at “Low” fan speed.

CLEANING DISCS:When ambient humidity is sensed atgreater than 75% humidity the cleaningdiscs will stop spinning. When ambienthumidity is sensed less than 60%, the disc,resumes to circulate.

Push the FUNCTION button to select Continuous Mode. - Continuous Mode Indicator will illuminate. - The FUNCTION button will cycle the unit between the following: Auto -> Continuous -> Sleep


Operation

17

Sleep Mode

Adjust Fan Speed

1

2

Push the FUNCTION button to select Sleep Mode.

The MODE button will cycle the unitbetween the following:

Auto -> Continuous -> Sleep

During Sleep Mode the unit will set fanspeed to lowest setting and the displaywill turn off, except for the low fan speedindicator.

Push the FAN SPEED button to change the Fan Speed.

The FAN SPEED button will cycle the unitbetween the following:

Low -> Med -> High


During Humidification process

During PlasmaWave® operation only

18

Adjust Timer

PlasmaWave® Technology

Lock Button

Push TIMER button to set a timer.

Push PLASMAWAVE/LOCK button for more than 3 seconds to activate Lock.

During Humidification process

The TIMER button will cycle through the unit timer settings:

2 hours -> 4 hours -> 8 hours

Push PLASMAWAVE/LOCK button to operate PlasmaWave®.

During PlasmaWave® operation only

Use this button to turn PlasmaWave®

function ON/OFF

Push PLASMAWAVE/LOCK button to operate PlasmaWave® while the unit OFF.

Use this button to turn PlasmaWave®

function ON/OFF without using thehumidification function of the unit.


19

Care & Maintenance

1 2

3

4 5

Emptying the Water Tank

Use the tab on the bottom of thewater tank and gently slide it outto open.

Lift disc assembly by the antibacterial handle and carefully remove it.

Remove the used water left in the water tank and dispose of it in anappropriate manner. Refill water tank with clean water.

Replace the water tank with asnap.

Gently slide down the frontpanel to close.

Be sure to change water frequently to ensure optimalfunctioning of the unit. Be sure to replace the water tank correctly in order toensure that the unit functions properly.


20

Cleaning Surface

Cleaning Rear Air Intake Grille

Unplug the HumidiPür™ before performing any type of maintenance such as cleaning or disassembling.

Do NOT clean the top portion of the unit with water.

Empty and unplug if not operating for more than 2 days.

Clean the outside of the unit with a softcloth and mild detergent. Wipe clean witha dry cloth.

Use the tab on the back cover grilleand pull up on the Combo Filter.

To clean the back cover grille rinselightly under warm water and air dry.

After cleaning, and letting air dry, slide the HEPA + Carbon Filter back intoit’s original location and replace the back cover grille.


2

1

CleanCel® Anti-bacterial Cleaning Discs are dish washer safe and can be washed in temperatures no greater than 176OF

Care & Maintenance

Cleaning Anti-bacterial Discs

Be sure to clean the Anti-bacterial Discs once a week

Clean Anti-bacterial Discs with warmtap water and a light detergent.

Fill warm tap water with detergentin the water tank.

Clean inside of the cycledAnti-bacterial Discs thoroughly.

21


2

1

3

4

22

Turn Gear of the Antibacterial Disccounterclockwise, and pull the frontof the Disc out, and separate axis fromthe rear Gear Disc, by turning it counterclockwise.

Rinse Antibacterial Disc with warmtap water and a mild detergent.

Clean the inside of water tank witha soft cloth and mild detergent.

After cleaning, assemble the parts(Gear Disc, Discs, and Saw Tooth GearDisc) in the opposite order.

Gear DiscDisc Plate

Saw ToothGear DiscDisc PlateAxis

(inside)Disc


23

Care & Maintenance

Cleaning Water Tank

Clean the inside of the water tankwith a soft cloth and mild detergent.

1

2

3

4

Place CleanCel® Anti-bacterial Discsback into the water tank aligningwith grooces and with handle laid flat.

Replace the Water Tank with a snap.

Gently slide down the front panel toclose the unit. Make sure that it is seated properly and lines up correctly.


24

Cleaning Inner Parts and Fan

1

2

3

4

5

Turn groove to open with a coin or flattip screw driver, at the rear of the unit,and remove top cover.

Holding fan, turn fan cap clockwise.

Rinse fan and fan cap with warm tapwater with detergent.

Remove dust near airflow inlet of theunit by using vacuum cleaner or softbrush.

After cleaning, replace fan and fan cap.


25

Care & Maintenance

Symptom

HumidiPür™ doesnot turn on

Auto Mode is not working

Vibrates or makes noise

Power cord is hot

Power cord is plugged in.

Low Water Indicator light is on.

Water is filled inside water tank.


Auto Mode Indicator is on.

The unit is located on an uneven surface.


Plug the power cord in.

Fill the water tank

Make sure the watertank is in place andfilled correctly.

Unplug power cordand plug it back in.

Push FUNCTIONbutton to selectAuto Mode.

Move to an evensurface.

Unplug the powercord and contactcustomer support.

Check If: Solution:


26

¢ ¢¢ ¢

Symptom

HumidiPür™ doesnot turn on

Function buttonis not working

Unpleasant odorsare present

Water level indicatoris on despite water level

Water is ground water.

Water is too cold or icy.

Fan speed is on low level.

Child-Lock mode is on.

HumidiPür™ is beingused where strong odors and/or dust ispresent

Water is left inside thewater tank.

Change to tap water.

Use 68˚F to 77˚Ftemperature water.

Change to high fanspeed.

Push Plasma/Child Lockbutton for 3 seconds toturn OFF Child-Lockmode.

Replace the water inthe water tank and change water morefrequently.

Clean water tank andCleanCel®

Anti-bacterial Discs.

Refill the water tank.

Check If: Solution:


27

Specifications

Model No.

Power Supply

PowerConsumption

Humdiifying Capacity

Tank (Max/Full)

Weight

Dimensions (D x H x W)

AW600

220V/ 50Hz

16W

12 Liter per day

5 Liter / 7 Liter

8.5 kg

345 x 450 x 345


Notes

merlin-technology.com

MERLIN® Technology GmbH

Hannesgrub Süd 10 4911 Tumeltsham / Ried i.I.

AUSTRIA

Tel +43 (0) 7752 71966Fax +43 (0) 7752 71988

[email protected]

Weitere Normen:

ÖNORM H 6020-1:2007 „Lüftungstechnische Anlagen in

Krankenanstalten – Projektierung, Errichtung und Kontrolle“

ISO 13485:2012 „Medizinprodukte – Qualitätsmanagement-

systeme – Anforderungen für Regulative Zwecke“

Superior Service & Qualität

Seit 1995

Documents

uSer manual - Climatronics · User manual Air humidifier and cleaner AIR-C60 — version 2015