WB-35/SOX/DT WB-35/SP - Emil Otto

Flux- und Oberflächentechnik GmbH

Eltviller Landstr. 22, 65346 Eltville, GermanyTel.: +49 (0)6123-7046-0 Fax: +49 (0)6123-7046-15

www.emilotto.de

Aqueous, low solids flux for wave soldering with halogen free activators and resin free (WEEE/RoHS conformant)DIN EN 61190-1-1: (IEC OR/LO) or type 2.1.3.A under ISO 9454

WB-35/SOX/DT Cat. no.2125

WB-35/SOX/DT has a high activity and is characterized by outstanding wetting properties. The flux is particularly suited to treating circuit boards of variable quality in terms of solderability. Application is by using a spray fluxer.

Solids content:Appearance:

Technical data:

Density at 20 °C: Acid number:

Solvent:Flashpoint:

Activators:

3.5 wt%clear, colourless liquid

1.020 (±0.02) g/ml28.0 - 32.0 mg KOH/g

waternot applicable

(di)carboxylic acids

Packing units:Cans containing 5 or 20 liters each. Liters

Picture may differ from original product.

Aqueous, low solids flux for wave soldering (low VOC) with halo-gen free activators and resin free. (WEEE/RoHS conformant) DIN EN 61190-1-1: (IEC OR/LO) or type 2.1.3.A under ISO 9454

WB-35/SP Cat. no.2136

WB-35/SP exhibits high activity and delivers outstanding wetting properties which are achieved due to our specially developed special combination of carrier substances. This flux is also well suited to treat circuit boards of variable soldering quality. Application is by using a spray fluxer.


Technical data:


Solvent:Flashpoint:

Activators:


0.98 - 1.00 g/ml28.0 - 32.0 mg KOH/g

water basednot applicable




Our customers have repeatedly expressed the need for ecological and sustainable products, normally during the course of customer specific flux development. As a Company orientated and totally committed to sustain-ability and customer requirements, we have expanded our research and development work and focused on the formulation and production of organic fluxes.Our aim was not just to develop an ecological range of products, but also an environmentally compatible pro-duction combined with simplified cost effective transport and storage. Our Green Line products are water based and thus completely biodegradable. Furthermore, they do not fall into the hazardous goods class and thus can be transported and stored in the conventional manner. This simple conventional transportation and storage represents a considerable added value advantage for our customers.Products within the Green Line range, contain fluxes for both selective and wave soldering, and all our fluxes can be used on commercially available production sys-tems. Your soldering results will correspond to those currently achieved with alcohol based fluxes, and a switch to an ecological water based flux is possible for you with some ease.We‘ll gladly support you during this changeover and help you to find the right product for your sustainable, cost saving, environmentally friendly production

Ecological Flux for Electronics Production

WB-30/EK-1401 was developed primarily for use on wave soldering machines and has a relatively high activity level. Practice has shown that with correct application, the washing / cleaning of circuit boards soldered with this flux can be largely dispensed with due to the very low solids content giving the assembled board a very good cosmetic appearance after soldering. This low resin content also ensures a pro-tective covering for the flux residues thereby positively enhancing the surface resistance results. Application is by using a spray fluxer.

Aqueous, low solids flux for wave soldering with halogen free ac-tivators and low synthetic resin content (WEEE/RoHS conformant)DIN EN 61190-1-1: (IEC OR/LO) or type 2.2.3.A under ISO 9454

WB-30/EK-1401


Cat. no. 2107

WB-30/EK-1405 was developed for use on wave soldering machines and has a relatively high activity level. The low resin content ensures a protective covering for the flux residues thereby positively enhancing the surface resistance results. Application is by using a spray fluxer.

Aqueous, low solids flux for wave soldering with halogen free activators and low resin content. (WEEE/RoHS conformant)DIN EN 61190-1-1: (IEC OR/LO) or type 2.2.3.A under ISO 9454

WB-30/EK-1405


Cat. no. 2106

Picture may differ from original product. Picture may differ from original product.

Aqueous, low solids flux for wave soldering with halogen-free activators and resin free. (WEEE/RoHS conformant)DIN EN 61190-1-1: (IEC OR/LO) or type 2.1.3.A under ISO 9454

WB-35/SOX Cat. no. 2118

WB-35/SOX has a high activity level and this flux is well suited to treat circuit boards of variable soldering quality. Live production has shown that with the correct application, washing / cleaning of circuit boards soldered with this flux can be largely dispensed with due to the very low solids content and cosmetic appearance of the assembled board. Application is by using a spray fluxer.




Technical data:


Solvent:Flashpoint:

Activators:

3.0 wt%clear, pellucid liquid

1.000 - 1.02 g/ml24.0 - 27.0 mg KOH/g

waternot applicable



Technical data:


Solvent:Flashpoint:

Activators:

3.0 wt%clear, pellucid liquid

1.000 (±0.005) g/ml21.0 - 25.0 mg KOH/g

waternot applicable



Technical data:


Solvent:Flashpoint:

Activators:


1.020 (±0.02) g/ml28.0 - 32.0 mg KOH/g

waternot applicable


Documents

WB-35/SOX/DT WB-35/SP - Emil Otto