Embed Size (px)
Citation preview
A C
36.5 b
A A
AB
αα
A
B
C
A
B
A
B
A
Alátétfa
270
60 -
90
9
-
-
0181
1 225
3
270
270
60 -
90
9
-
-
081
1230
62
330
60 -
75
330
90-1
35
330
270
330
330
330
330
135
330
30-7
5
270
30 -
45
270
60-9
0
270
135
270
270
270
270 270
60-9
0
270
135
330
30 -
45
330
60-7
5
330
90-1
35 270
ill. 3
3033
0 330
330
135
A
B
B
A
B
D
C
B
A
F
E
The Formwork Experts.
Framed formwork Framax Xlife plusLightning-fast assembly thanks to new-generation form-ties
9994
4230
2 - 0
5/20
20 e
n-GB
Panel sizes1
Examples of stacking variants
Closure
Plumbing accessories Guardrail system
2
5
8 9
Inter-panel connections4 Tying6
Stop-end formwork7
Corner solutions and wall steps3
Tying across the top of the panel Repositioning
Additional note on tying
Practical tips User Information
i
i
i
i
Framax head anchorFramax-Kopfanker
Galvanised, powder-coated
kg Art. n°
15 - 40 cm 4.2 58896900015 - 100 cm 6.1 588970000
Framax Xlife plus panelsFramax Xlife plus-Elemente
Galvanised
2.70x3.30m 521.5 5892900002.70x2.70m 435.5 589260000
Panel sizes1
1.35x3.30m 273.0 589291000C 0.90x3.30m 196.6 589292500C 0.75x3.30m 174.7 589293500C 0.60x3.30m 137.7 589294500C 0.55x3.30m 128.3 589330500C 0.50x3.30m 121.2 589331500C 0.45x3.30m 114.5 589295500C 0.30x3.30m 89.3 589296500
1.35x2.70m 222.5 5892610000.90x2.70m 151.0 5892620000.75x2.70m 135.5 5892630000.60x2.70m 107.0 5892640000.55x2.70m 96.0 5893320000.50x2.70m 93.6 5893330000.45x2.70m 87.0 5892650000.30x2.70m 67.5 589266000
Galvanised, powder-coated
1.35x1.35m 114.0 5892670000.90x1.35m 78.3 5892680000.75x1.35m 71.0 5892690000.60x1.35m 57.5 5892700000.55x1.35m 53.0 5893340000.50x1.35m 49.8 5893350000.45x1.35m 46.0 5892710000.30x1.35m 35.5 589272000
0.90x0.60m 42.8 5893130000.75x0.60m 38.8 5893140000.60x0.60m 33.0 5893150000.55x0.60m 27.5 5893360000.50x0.60m 27.4 5893370000.45x0.60m 24.5 5893160000.30x0.60m 18.4 589317000
Galvanised, powder-coated
kg Art. n°
kg Art. n°kg Art. n°
Corner solutions3
Framax Xlife plus outs. corner 10/10cmFramax Xlife plus-Außenecken 10/30
Galvanised, powder-coated
3.30m 87.4 589310000 2.70m 72.5 589311000 1.35m 39.5 589312000 0.60m 19.8 589320000
3.30m 209.9 5886760002.70m 171.0 5886750001.35m 90.0 588614000
Framax stripping corner IFramax-Ausschalecke I
Galvanised, powder-coated
Framax stripping spindle IFramax-Ausschalspindel I
Galvanised, height: 25 cm
Framax stripping spindle I with ratchetFramax-Ausschalspindel I mit Ratsche
Galvanised, height: 24.8 cm 5.5 588653000
Framax triangular ledge 2.70mFramax-Dreikantleiste 2,70m
Framax frontal triangular ledgeFramax-Stirndreikantleiste
Grey
Framax Xlife universal panelsFramax Xlife-Uni-Elemente
Galvanised, powder-coated, corners marked in blue
0.90 x 3.30m 182.6 5882285000.90 x 2.70m 148.0 5881225000.90 x 1.35m 79.3 5881245000.90 x 0.90m 63.0 588120500
Framax outside cornersFramax-Außenecken
Galvanised
3.30m 58.0 5882270002.70m 47.0 5881260001.35m 23.5 5881280000.60m 11.1 589319000
3.2 588618000
2.70m 1.70 588129000 3.30m 2.00 588949000
0.38 588170000
Framax quick acting clamp RUFramax-Schnellspanner RU
Galvanised, length: 20 cm
Galvanised, length: 21 cm
3.3 588153400
Framax multi function clampFramax Uni-Spanner
Galvanised, length: 40 cm 5.8 588169000
Framax adjustable clamp*Framax-Ausgleichsspanner
Galvanised, length: 48 cm 5.3 588168000
Inter-panel connections
Painted blue, leg-length: 60 cm
Framax universal walingFramax-Klemmschiene
0.60m 6.6 5886890000.90m 10.6 5881500001.50m 16.8 588148000
Painted blue
4
Framax wedge clampFramax-Spannklemme
Super plate 15.0Superplatte 15,0
Galvanised, height: 6 cmDiameter: 12 cm, width across flats: 27 mm
Star grip nut 15.0 GSternmutter 15,0 GGalvanised, width: 10 cmHeight: 5 cm, width across flats: 26 mm
Framax universal corner walingFramax-Eckklemmschiene
Framax universal fixing bolt Framax-Universalverbinder
Galvanised Universal fixing bolt 10 - 16cm 0.60 588158000Length: 26 cmUniversal fixing bolt 10 - 25cm 0.69 583002000 Length: 36 cm
1.5 588152000
1.1 581966000
0.43 587544000
12.8 588151000
Framax moulded timberFramax-Profilholz
Framax alu closuresFramax-Alu-Ausgleiche
Varnished yellowPowder-coated Varnished yellow
Framax formwork fitting timber Framax-Ausschalholz
Framax fitting-timbersFramax-Passhölzer
2x12cm 2.70m 3.1 1760200003x12cm 2.70m 4.7 1760220005x12cm 2.70m 7.8 17602400010x12cm 2.70m 15.5 1760260002x12cm 3.30m 3.8 1760210003x12cm 3.30m 5.7 1760230005x12cm 3.30m 9.5 17602500010x12cm 3.30m 19.0 176027000
Varnished yellow
Closure
10x12cm 2.85m 16.4 17600800010x12cm 3.45m 19.9 176014000
27mm 2.70m 7.6 17601200021mm 2.70m 8.0 17601000018mm 2.70m 8.4 17611900027mm 3.30m 9.3 17601300021mm 3.30m 9.8 17601100018mm 3.30m 10.2 176120000
5cm 0.60m 1.9 58924200010cm 0.60m 2.6 5892430005cm 1.35m 4.4 58922400010cm 1.35m 5.7 5892250005cm 2.70m 8.5 58922600010cm 2.70m 11.0 5892270005cm 3.30m 10.5 58922800010cm 3.30m 12.9 589229000
5
Framax Xlife plus form tie 20.0 Framax Xlife plus-Anker 20,0
15 - 30 cm 5.0 589277000Length: 70 cm25 - 40 cm 5.4 589278000Length: 80 cm45 - 60 cm 6.2 589298000Length: 100 cm
Tying6
Framax Xlife plus form-tie nut 20.0Framax Xlife plus Ankermutter 20,0
Length: 16 cm 2.3 589279000
Length: 12 cm
Framax Xlife plus form-tie nut I 20.0Framax Xlife plus Ankermutter I 20,0
1.2 589216500
Galvanised, length: 20 cm
Framax Xlife plus parking boltFramax Xlife plus-Parkbolzen
0.42 589327000
Framax Xlife plus distance protectorFramax Xlife plus- Distanzsicherung
Galvanised, height: 23 cm,Spanner size (width across flats): 24 mm
1.3 589217000
Framax Xlife plus ratchet 1/2" SW24 LFramax Xlife plus-Knarre 1/2“ SW24 L
Length: 30 cm 0.92 589221000
Framax Xlife plus ratchet 3/4" SW24Framax Xlife plus-Knarre 3/4" SW24
4.4 589220000
0.09 589282000
Framax Xlife plus fair-faced concr. cone 87mmFramax Xlife plus-Sichtbetonkonus 87mm
Blue
PE, grey
PE, colourless
PE, grey
Grey
0.28 589284000GalvanisedLength: 5.5 cm
Framax Xlife plus cone spannerFramax Xlife plus-Konusschlüssel
0.19 589283000
Framax Xlife plus fair-faced concr. plug 87mmFramax Xlife plus-Sichtbetonstopfen 87mm
Framax Xlife plus plug 24mmFramax Xlife plus-Verschlussstopfen 24mm
Framax Xlife plus plug 24mm with holeFramax Xlife plus-Verschlussstopfen 24mm mit Loch
Framax Xlife plus plug 38mmFramax Xlife plus-Verschlussstopfen 38mm
0.005 589219000
0.004 589223000
0.006 589288000
Framax Xlife plus frame hole plug 32mm NGFramax Xlife plus-Ankerstopfen 32mm NG
0.005 589280500Black Diameter: 3.5 cm
Framax Xlife plus reducer I 20.0Framax Xlife plus-Reduzierstück I 20,0
0.60 589329000Galvanised Length: 12.5 cm
EPDM, PA, blackSpanner size (width across flats): 17 mm
0.10 589308000
Framax Xlife plus screw plug 25mmFramax Xlife plus-Schraubstopfen 25mm
Length: 100 cm
Stop-end formworkFramax stop-end tieFramax-Stirnanker
Galvanised, length: 29 cm 1.5 588143000
Framax stop-end waler tie 15-45cmFramax-Stirnabschalzwinge 15-45cm
Galvanised
Framax stop-end waler tie 15-75cmFramax-Stirnabschalzwinge 15-75cm
Galvanised
7
Plumbing accessories
Panel strutsElementstützen
Galvanised, delivery condition: folded
Galvanised, delivery condition: folded
Panel strut 340 IB
Panel strut 540 IB
24.3 580365000
41.4 580366000
8
Framax lifting hookFramax-Umsetzbügel
Galvanised, height: 22 cmFollow the directions in the Operating Instructions!
10.6 588149000
Framax Xlife plus stacking cone IFramax Xlife plus-Stapelkonus I
Framax Xlife plus stacking coneFramax Xlife plus-Stapelkonus
Black, diameter: 8 cm
Blue, diameter: 8 cm
0.03 589286000
0.03 589285000
15.0 588940000 20.6 588941000
kg Art. n°
kg
kg
Art. n°
Art. n°
kg Art. n°
kg Art. n°
kg Art. n°kg Art. n° kg Art. n°
kg Art. n°
kgkg
Art. n°Art. n°
kg Art. n°kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg
kg
kg
Art. n°
Art. n°
Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
Only tool
needed: ratchet
width across flats
24
All the User Information booklets for the systems shown have been posted at www.doka.com/framax-xlife-plus-info, along with useful construction and usage tips for more efficiency on site.
Should you have any questions, your Doka adviser will always be pleased to advise.
LegendFramax Xlife plus Form tie 20.0
Framax quick acting clamp RU
Framax multi function clamp
Framax universal waling
Framax wedge clamp
Mounting the Form-tie nut I 20.0 � Position the form-tie nut in the form-tie sleeve of the framed formwork panel (hook engages in recess)
� Push the centring disc in and at the same time turn it through 180°.
� As soon as the centring disc engages, the form-tie nut is fixed in place.
Other functionsInter-panel connection without infill
Inter-panel connection for stacking
Squared timber conn. up to 20 cm
Corner connection for foundations
Height: 3.00 m to 3.15 m
Height: 3.60 m to 3.75 m
Height: 3.30 m to 3.60 m
Height: 3.90 m to 4.05 m Height: 4.20 m to 4.65 m Height: 6.00 m or 6.60 m
Height: 6.00 m to 6.30 m
Height: 7.95 m
Height: 6.75 m
Park the Framax Xlife plus form tie in the distance protector in preparation for repositioning of the gang-form. In the parking position, the form tie automatically stays vertical and cannot drop out when the panel is turned on to its side.
Framax Xlife plus panelsSystem logic
The system logic of Framax Xlife plus optimises material utilisation and logistics for a better overview on site. The basic panel is square, there are only a few standard-panels formats and they all stack longside horizontally – so there is no need for small panels of many different sizes to make up gangforms.
Form shafts even faster and with fewer form ties
Wall stepT-junction
90 degree corners with the Framax Xlife plus inside corner 30/30cm
Variant with Framax Xlife plus outside corner 10/10cm
with panels fixed by form ties in the middle, in conjunction with the Framax stripping corner I
For more information on configurations for corners see the User Information booklet for Framax Xlife plus.
Closures 0 - 15 cm
with Framax alu closure / Framax fitting timber
and Framax multi function clamp
Closures 0 - 20 cm
with Framax alu closure / Framax fitting timber
and Framax adjustable clamp
Basic rule:
� One-sided operation requires only one person � For wall thicknesses from 15 cm to 60 cm � Permitted capacity: 150 kN � No installation of jacket tubes and cones � Fit one form tie in each form-tie sleeve
Tie rod system Framax Xlife plus
Please note: The Framax Xlife plus panels can be combined in many different ways, resulting in countless possible variations when they need to be vertically stacked. Given below are various examples of stacking configurations using the Framax quick acting clamp RU and Framax multi function clamp. Further examples can be found in the User Information booklet for Framax Xlife plus.
Framax Xlife plus panels 2.70m
Framax Xlife plus panels 3.30m
Simple inter-panel connectionwith Framax quick acting clamp RU
Self-aligning inter-panel connection with filler option using Framax multi function clamp
Other functionsVertical stacking with moulded timber
Filler connection up to 15 cm
� Connector for infills up to 15 cm � Perfectly matched to the panel size-grid � Self-aligning, crane-handling-safe connections between the panels
Joining the panels using the Framax multi function clamp provides additional bracing of the gang-form (as the clamp bears directly onto the profile).
Particularly when panels are stacked in the vertical, the fact that the clamp bears directly on the profiles means that there is often no need for any extra bracing of the panels with universal walings.
With its 15 cm clamping range, the Framax multi-function clamp exactly matches the panel size-grid. For more information, see the User Information booklet.
The number of panel connectors in the corner area and with stop end formwork in accordance with the User Information.
Panel height Number of clamps0.60 m 1
1.35 m 2
2.70 m 2
3.30 m 3
Panel height Number of clamps0.30 m 1
0.45 m 1
0.60 m 2
0.75 m 2
0.90 m 2
1.35 m 2
Panels standing upright
Number of panel connectors vertical joint
Panels longside horizontal:
High stability and easy alignment thanks to the robust panel struts.
Panel strut 340
Eurex 60 550
Panel strut 540
Close-up: showing how the panel strut is fastened to the integrated waling system
Number of struts per 2.70 m width of gang-form:Anchoring the panel struts with the express anchorThe Doka express anchor can be re-used many times over.
*) Up to a height of 3.30 m, the pitch between the rakers can be increased to 4.05 m.
Values applicable to wind pressure we = 0.65 kN/m2. For more information, see the Calculation Guide 'Wind loads to the Eurocode'.
Please note: Every gang-form must be supported by at least 2 panel struts.
Example: Where the formwork height is 7.20 m, the following are needed for every 5.40 m wide gang-form: 2 panel struts 340 4 panel struts 540
Doka express anchor 16x125mm
Doka coil 16mm
Hole diameter 16 mmHole depth 140 mm
Formwork height [m] Panel strut 340 540
Eurex 60 Plumbing strut
4.05 1 *)
5.40 1
6.00 1 1
7.20 1 2
8.10 1 1
Max. anchoring load: FK = 13.5 kN (Rd = 20.3 kN)
A pre-assembled, foldable, ready-to-use platform with a width of 1.25 m for convenient, safe working.
For assembling pouring platforms with a 90 cm width. Easily mounted by hand.
Framax pouring platform U
The Platform system Xsafe plus offers maximum safety for Doka wall formwork systems.
� pre-assemled, fold-away working platforms � integrated side railings � self-closing manhole lids � ready for immediate use � quick, safe working, even at significant formwork heights
� in combination with the Xsafe plus lifting adapter Framax, quickly usable as suspended pouring platform
Observe counter railing requirements as per legal regulations!
By combining the Framax alu closures (5 and 10 cm) and the Framax fitting timbers (2, 3, 5 and 10 cm) in various ways, closures can be made in 1 cm increments.
Xsafe plus platform
Xsafe plus lifting adapter Framax (2 per platform)
Platform system Xsafe plus Framax bracket 90 EP
The large, conical form-tie sleeves allow the panels to be inclined on one or both sides, and be offset vertically and laterally.
*) with form tie 45 - 60 cm larger wall thicknesses also possible
Please note: Secure inclined panels against uplift, for example with Doka express anchors and floor fixing plates. See the User Information booklet for details of accessories.
Please note: Spraying the conical part of the form tie with release agent makes it easier to detach the form tie from the concrete.
The Framax head anchor transmits tensile and compressive forces and replaces: � Tie rod � Super plates � Framax tie-holder bracket � Wooden spacer
Please note: Panel bracing and guardrail system not shown in this illustration. Observe Chapters 8 and 9 of the poster and the User Information booklet.
Height offset / side offset
max. 1.0 cm per 15 cm of wall thickness
Conical on one side
max. 4°
Conical on both sides
max. 2 x 4°
Framax lifting hookUse as foundation formwork
Use as wall formwork
Positioning of the Framax lifting hook
Framax assembling tool
For operating the lifting hook from ground level up to a formwork height of 3.30 m (with telescopic assembling tool upt to 5.40 m)
Observe the annual check of the lifting hooks!
up to 60 cm over 60 cm
Always place the Framax lifting hook over one of the welded-on metal plates, to prevent it from sliding from side to side.
Transporting the panels
The Framax transport bolts (A), in combination with the Doka 4-part chain 3.20m (B), are for moving panels either individually or in stacks.
Stacking the panels
Please note: Form-tie nut I 20.0 does not have to be removed for stacking the panels. Use Stacking cone I for this purpose.
Offloading and lifting
The Dokamatic lifting strap 13.00m is a practical tool for offloading or loading trucks, and for hoisting stacks of panels.
Framax stripping tool – Easy and fast formwork stripping
Framed formwork is very easy to detach from the concrete with the Framax stripping tool.
Variant with Framax Xlife universal panels
Wall step 30 cmWall thickness up to 30 cm Wall step 35 – 90 cm
Stop-end formwork with Framax universal waling and Framax universal fixing bolt
Stop end with Framax stop-end waler tie
Stop end with Framax universal panel and Framax universal fixing bolt
Parking position for form tie
Ingeniously co-ordinated panel formats help you make optimum use of formwork commissioning quantities.
All dimensions in m
Tie rod system with Form-tie nut I 20.0
Please note: No need for removal when panels are stacked for storage
Standard position of the stop cylinder for wall thicknesses from 15 cm to 40.0 cm *)
Stop cylinder, turned 180° for wall thicknesses from 15,5 cm to 40.5 cm *)
Wall thicknesses in 0.5 cm increments
Holding formwork Opposing formwork
Example: Wall thickness = 36.5 cm
Adapting to the wall thicknessInclination of panels with offset between panels
Tying the panels Removing the form ties
Control marking on the tie rod
Marking groove on the stop cylinder
"+0,5" for 0.5 cm increments
Mounting the Form-tie nut 20.0 � Position the form-tie nut into the anchoring sleeve of the framed formwork panel and screw it on.
� Set up the opposing formwork. � Mount the distance protector at the form-tie point (do not tighten the screw yet), and tilt it to the left.
� Loosen the screw (a/f 24) and pivot the distance protector away.
� Use the ratchet to unscrew the form tie.
� Screw in the form tie with the ratchet until it is fully engaged and tighten it firmly. Tightening torque: approx. 100 Nm
� Pivot the distance protector over the form tie and tighten the screw (a/f 24). Tightening torque: max. 80 Nm
Framax Xlife plus stack-ing cone
Strapping tape
b ... wall thickness + 10 cm
Park the Framax Xlife plus form tie in the distance protector in preparation for repositioning of the gang-form.
In the parking position, the form tie automatically stays vertical and cannot drop out when the panel is turned on to its side.
Parking position Form tie
Height: 4.05 m Height: 5.40 m
α ... max 4°
Framax head anchor
Framax head anchor
Joint-sealing tape
Panel 2.70x3.30mtwo formwork heights in one panel with surface area of 8.9 m²
The Framax head anchor re-places the topmost form ties for: � panel height 3.30 m � stacking elements up to 0.90 m
Insert the parking bolt into the hole in the cross profile.
Push the form-tie nut on to the parking bolt from below and secure it with a spring cotter.
Parking position Form-tie nut I
Framax Xlife plus inside corner 30/30cm
Framax Xlife plus outs. corner 10/10cm
3.30
m
0.90
m2.
70 m
Eurex 60 550Eurex 60 550
Delivery condition: individual parts
Depending on the length required, consisting of:
Plumbing strut Eurex 60 550 42.5 582658000
blue powder-coated, alu, length: 343 - 553 cm
Extension Eurex 60 2.00m 21.3 582651000
blue powder-coated, alu, length: 250 cm
Coupler Eurex 60 8.6 582652000
Aluminium, length: 100 cm, diameter: 12.8 cm
Connector Eurex 60 IB 4.2 582657500
Galvanised, length: 15 cm, width: 15 cm, height: 30 cm
Plumbing strut shoe Eurex 60 EB 8.0 582660500
Galvanised, length: 31 cm, width: 12 cm, height: 33 cm
Adjusting strut 540 Eurex 60 IB 27.8 582659500
Galvanised, length: 303.5 - 542.2 cm
A
B
C
D
E
F
kg Art. n°
kg Art. n°
kg
kg
Art. n°
Art. n°
Doka express anchor 16x125mmDoka-Expressanker 16x125mm
Prop head EBStützenkopf EB
GalvanisedLength: 18 cmFollow Fitting Instructions!
Galvanised, length: 40.8 cmWidth: 11.8 cm, height: 17.6 cm
0.31 588631000
3.1 588244500
Doka coil 16mmDoka-Coil 16mm
Galvanised, diameter: 1.6 cm
0.009 588633000
The articles shown here represent a selection from the full range. More articles can be found in the User Information booklets of the relevant systems.
Lifting, transporting, stacking and storingi
Practical tips
kg Art. n°
kg
kg
Art. n°
Art. n°
kg Art. n°
Galvanised, length: 193 cm
AluLength: 227 - 398 cm
Framax assembling toolFramax-Montagestange
Framax telescopic assembling toolFramax-Teleskop-Montagestange
4.2 588678000
4.5 588651000
Galvanised
Galvanised, length: 110 cm
Double scraper Xlife 100/150mm 1.40mDoppelschaber Xlife 100/150mm 1,40m
Framax stripping toolFramax-Ausschalwerkzeug
2.8 588674000
5.5 589235000
i
Guardrail systemsXsafe plus platform Xsafe plus-Bühne
Steel parts galvanised, timber parts varnished yellow, height: 136 cm, Delivery condition: folded
Protective grating XPSchutzgitter XP
Xsafe plus side railingXsafe plus-Seitengeländer
Xsafe plus lifting adapter FramaxXsafe plus-Umsetzadapter Framax
Handrail clamp SSchutzgeländerzwinge S
Galvanised Height: 123 - 171 cm
GalvanisedHeight: 134 cm
Handrail post 1.10mSchutzgeländer 1,10m
GalvanisedLength: 115 - 175 cmHeight: 112 cm
Galvanised, height: 56 cm
Galvanised
Galvanised
Side handrail clamping unit TSeitenschutzgeländer T
Framax adapter XP Framax-Adapter XP
Handrail post XP 1.20mGeländersteher XP 1,20m
Protective grating XP 2.70x1.20m 22.2 586450000Protective grating XP 2.50x1.20m 20.5 586451000Protective grating XP 2.00x1.20m 17.4 586452000Protective grating XP 1.20x1.20m 12.0 586453000
Xsafe plus counter railingXsafe plus-Gegengeländer
Handrail post 1.00mGeländer 1,00m
Xsafe plus platform 1.35m Xsafe plus platform 2.40mXsafe plus platform 2.70m
Galvanised Width: 88 cm, Height: 110 cm
Galvanised, Height: 51.4 cm
Galvanised, height: 200 cmDelivery condition: folded
Xsafe plus counter railing 1.35mXsafe plus counter railing 2.40mXsafe plus counter railing 2.70m
kg Art. n°
kg Art. n°
kg Art. n°
kg Art. n°
95.3 586408000 142.7 586406000 151.7 586404000
20.5 586410000
6.6 586436000
17.0 586429000 22.0 586427000 23.5 586425000 kg Art. n°
kg Art. n°
kg Art. n° kg Art. n°
kg Art. n°
kg Art. n°
11.5 580470000
5.5 584384000
Galvanised
29.1 580488000
8.0 586475000
4.1 586460000
kg Art. n°
3.8 584335000
9
Framax bracket 90 EPFramax-Konsole 90 EP
Bracket adapter XP FRR 50/30cmKonsolenadapter XP FRR 50/30cm
Galvanised, length: 102.8 cm Width: 13 cm, height: 83.2 cm
kg Art. n°
8.7 588979000
kg Art. n°
2.4 586486000
Art. n°
117.0 588360000 127.5 588377000
Framax pouring platformFramax-Betonierbühne
Timber parts varnished yellow, steel parts galvanised, Delivery condition: folded
Framax pouring platform O 1.25/2.70mU 1.25/2.70m
kg
Galvanised
This poster is not a substitute for the applicable system User Information booklet!
Up to a height of 3.15 m, no form ties are needed in the stacked panelUniversal waling only needed if pouring platforms are to be used.
Up to a height of 3.75 m, no form ties are needed in the stacked panelUniversal waling only needed if pouring platforms are to be used.
Universal waling only needed if pouring platforms are to be used.
Universal waling only needed if pouring platforms are to be used.
Universal waling only needed if pouring platforms are to be used.
The third universal waling at the first panel joint is only needed if intermediate platforms are to be used.
Sleepers
3.30
2.70
3.30 2.70 1.35 0.60 3.30 2.70 1.35 0.60
3.30
2.70 3.
302.
701.
35
2.70 1.35 0.90 0.75 0.60 0.55 0.50 0.45 0.30
0.60
Panel widths, panel heights
2.70 1.35 0.90 0.75 0.60 0.450.55 0.50 0.30
3.30
3.30
1.35
0.60
2.70
2.70
3.30
2.70
3.30 3.302.70 2.701.35 1.350.60 0.60
2.7
0
m
1.3
5
0.6
0
0.3
0
0.4
5
0.5
0
0.5
5
0.7
5
0.9
0
3.30
1.35
0.60
0.30
0.45
0.50
0.55
0.75
0.90
2.70
![0.55 W[Standard] VF3000 - content2.smcetech.comcontent2.smcetech.com/pdf/VF1000-3000-5000_DE.pdf · Siehe unten stehende Grafik zur Leistungsaufnahme. Dichtungsmaterial: HNBR Ozonbeständige](https://img.pdfslide.org/doc/110x75/6081cc069e564f6672456da2/055-wstandard-vf3000-siehe-unten-stehende-grafik-zur-leistungsaufnahme-dichtungsmaterial.jpg)
