#iPASO400_softkey

8/10/2019 #iPASO400_softkey

1/5

Source Doc. No: IMPORTANT NOTICE, READ BEFORE USE Rev. No. & Date 400-iPASO116-01 / Mar 2011 Software key

As this document contains information necessary for NEC's internal document management such as revision numbers,revision history etc., it is strictly prohibited to provide this document in full, in printed or electronic form to the customers.However, necessary information without the internal references can be extracted and included in documents presented tothe customer.CONFIDENTIAL

SOFTWARE KEY iPASO-400

GeneralSoftware key is a powerful, yet easy-to-use multi-dimensional equipment management toolthat could facilitate the customers requirement for capacity and configuration expansion orupgrades. The iPASOLINK hardware support all capacities and configurations. Initiallycustomer can acquire the capacity and redundancy configuration required for the currenttraffic requirements to keep the cost down. When the traffic requirement expand or grows,additional capacities can be enabled by acquiring a software key.

To facilitate the customer requirements of larger traffic needs, software key is a powerful, yeteasy-to-use multi-dimensional equipment management tool to upgrade iPASOLINK 400.

1. KEY FEATURES AND BENEFITS

1.1 Upgradable by Software KeyUpgrading the equipment can be done easily by installing the software key.1.2 Product Cost DownThe software key function is a very cost effective feature that allows the customer to upgradethe system configuration.1.3 Upgrading Whenever NeededWhen traffic volume increases, you may need to increase the capacity. iPASOLINK 400 can

be upgraded by software key(s) whenever needed.1.4 Flexible Software Key SelectionSelect the software key depending on what needs to be upgraded/changed in your equipment.

2. SOFTWARE KEY TYPES

Software key is classified into two types:

Initial KeyInitial Key is installed into the equipment at the NEC factory before shipment.

Upgrade KeyUpgrade key is installed into iPASOLINK 400 equipment.Upgrade key is defined and made effective by a combination of two paramThe Parameter After Change is regarded as Parameter Before Change eters:Upgrade Key Item Name: Parameter Before Change to Parameter After change

Example:


2/5



Radio capacity-1: 10MB to 100MBin the next upgrade process.

Please refer to the following tables for initial/upgrade key variations.

System & Radio Key

No. Key Item Initial Key Key Configuration Upgrade Key-1 Upgrade Key-21 Radio Redundancy 1+0 Default 1+0 to 1+1 (1 pair) 1+0 to 1+1 (2 pair)

1+1 (1 pair) 1+1 (1 pair) to1+1 (2 pair)

1+1 (2 pair)2 ETH Traffic

Aggregation@N+0 Radio

OFF Default OFF to ON

ON

3 Radio BITRATE FIXED Default FIXED to FREE FIXED to AMRFREE FREE to AMRAMR

4 XPIC Function OFF Default OFF to XPIC 1P OFF to XPIC 2PXPIC 1P XPIC 1P to

XPIC 2PXPIC 2P

5 NEO ODUCompatibility

OFF Default OFF to ONON

Summary of the required soft-keys for radio system configurationConfiguration

N+0 N-way 1+1 2x(1+1) 1+0 XPIC 2x(1+0 XPIC)

1+1 XPIC

Radio Redundancy 1+0 1+0 1+1 1P 1+1 2P 1+0 1+0 1+1 1PRadio Capacity N key N key 1 key 2 key 2 key 4 key 2 keyXPIC Function OFF OFF OFF OFF XPIC 2P XPIC 2P XPIC 1P


3/5



Radio Capacity Key

Key Item InitialKey

KeyConfig

UpgradeKey-1

UpgradeKey-2

UpgradeKey-3

UpgradeKey-4

UpgradeKey-5

UpgradeKey-6

UpgradeKey-7

RadioCapacity

10MB Default 10MB to20MB

10MB to50MB

10MB to100MB

10MB to150MB

10MB to200MB

10MB to300MB

10MB to400MB

20MB 20MB to50MB

20MB to100MB

20MB to150MB

20MB to200MB

20MB to300MB

20MB to400MB

50MB 50MB to100MB

50MB to150MB

50MB to200MB

50MB to300MB

50MB to400MB

100MB 100MB to150MB

100MB to200MB

100MB to300MB

100MB to400MB

150MB 150MB to200MB

150MB to300MB

150MB to400MB

200MB 200MB to300MB

200MB to400MB

300MB 300MB to400MB400MB

The relation among Channel Spacing , Modulation Rate and Traffic rate are described as bellow.


4/5



ETH & TDM Key

No. Key Item InitialKey

Key Configuration Upgrade Key-1 Required OptionModule

1 RJ45 Port Usage inMain Board(2xFE or 2xGbE)

2xFE Default 2xFE to 2xGE

2xGbE

2 SFP Port Usage inMain Board

OFF Default OFF to 2xGbE2xGbE

3 SFP Port Usage peroptional GbE card

OFF GbE ModuleON

4 Additional VLANTable

OFF Default 256 to 4094 TableON

5 LAG/LACP forEthernet Line *1

OFF Default OFF to ONON

6 Ethernet OAM(CC/LT/LB) OFF Default OFF to ONON7 Ethernet OAM

(LM/DM)OFF Default OFF to ONON

8 QoS Classify 4 Lv Default 4 Lv to 8 Lv8 Lv

9 E1 SNCP OFF Default OFF to ON Clock ModuleON

10 STM-1 APSProtection *2

OFF Default OFF to ON STM1 ModuleON

11 STM-1MUX/DEMUX *2

OFF Default OFF to ON Clock ModuleSTM1 ModuleON

Note:*1


5/5


As this document contains information necessary for NEC's internal document management such as revision numbers,revision history etc., it is strictly prohibited to provide this document in full, in printed or electronic form to the customers.

documents presented toHowever, necessary information without the internal references can be extracted and included inthe customer.CONFIDENTIAL*2

Extension Function Key

No. Key Item InitialKey

Upgrade N/C Key(N/C: No Change)

Upgrade Key-1 Required OptionModule

1 Sync. ETH Clock OFF N/C OFF to ON CLK2M-CON

2 IEEE 1588v2 PTPClock

OFF N/C OFF to ON CLK2M-CON

Documents

#iPASO400_softkey